wolfg1969/boot.log

## boot.log
U-Boot 1.1.4 (Feb 28 2012 - 11:58:24)

AP121 (ar9330) U-boot

DRAM:  32 MB
led turning on for 1s...
id read 0x100000ff
flash size 4194304, sector count = 64
Flash:  4 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag7240_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
: cfg1 0x5 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
ag7240_phy_setup
eth0 up
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
athrs26_reg_init_lan
ATHRS26: resetting s26
ATHRS26: s26 reset done
ag7240_phy_setup
eth1 up
eth0, eth1
Autobooting in 1 seconds
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 3.3.8 (guoyong@guoyong-laptop) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #7 Sat Sep 1 20:49:34 CST 2012
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR9330 rev 1
[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00002000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00002000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line:  board=TL-WR703N console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 29276k/32768k available (2082k kernel code, 3492k reserved, 396k data, 204k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.090000] gpiochip_add: registered GPIOs 0 to 29 on device: ath79
[    0.100000] MIPS: machine is TP-LINK TL-WR703N v1
[    0.340000] bio: create slab <bio-0> at 0
[    0.350000] Switching to clocksource MIPS
[    0.350000] NET: Registered protocol family 2
[    0.360000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.360000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    0.360000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.370000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.380000] TCP reno registered
[    0.380000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.390000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.390000] NET: Registered protocol family 1
[    0.420000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.420000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.430000] msgmni has been set to 57
[    0.430000] io scheduler noop registered
[    0.440000] io scheduler deadline registered (default)
[    0.440000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.450000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
[    0.450000] console [ttyATH0] enabled, bootconsole disabled
[    0.450000] console [ttyATH0] enabled, bootconsole disabled
[    0.470000] m25p80 spi0.0: found en25q32b, expected m25p80
[    0.470000] m25p80 spi0.0: en25q32b (4096 Kbytes)
[    0.480000] 5 tp-link partitions found on MTD device spi0.0
[    0.480000] Creating 5 MTD partitions on "spi0.0":
[    0.490000] 0x000000000000-0x000000020000 : "u-boot"
[    0.490000] 0x000000020000-0x0000000fd9b4 : "kernel"
[    0.500000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.510000] 0x0000000fd9b4-0x0000003f0000 : "rootfs"
[    0.510000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.530000] mtd: partition "rootfs" set to be root filesystem
[    0.530000] mtd: partition "rootfs_data" created automatically, ofs=380000, len=70000
[    0.540000] 0x000000380000-0x0000003f0000 : "rootfs_data"
[    0.550000] 0x0000003f0000-0x000000400000 : "art"
[    0.550000] 0x000000020000-0x0000003f0000 : "firmware"
[    0.580000] ag71xx_mdio: probed
[    0.580000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[    1.130000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[    1.140000] TCP cubic registered
[    1.140000] NET: Registered protocol family 17
[    1.150000] 8021q: 802.1Q VLAN Support v1.8
[    1.160000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    1.160000] Freeing unused kernel memory: 204k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[    6.650000] JFFS2 notice: (404) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 7 of xref (0 dead, 0 orphan) found.
switching to jffs2
- init -

Please press Enter to activate this console. [    7.680000] Compat-wireless backport release: compat-wireless-2012-07-13
[    7.680000] Backport based on wireless-testing.git master-2012-07-16
[    7.690000] compat.git: wireless-testing.git
[    7.840000] cfg80211: Calling CRDA to update world regulatory domain
[    7.850000] cfg80211: World regulatory domain updated:
[    7.850000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    7.860000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    7.870000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    7.870000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    7.880000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    7.890000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    8.120000] usbcore: registered new interface driver usbfs
[    8.120000] usbcore: registered new interface driver hub
[    8.130000] usbcore: registered new device driver usb
[    8.690000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
[    8.700000] cfg80211: Calling CRDA for country: US
[    8.700000] cfg80211: Regulatory domain changed to country: US
[    8.710000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    8.720000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[    8.730000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[    8.730000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    8.740000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    8.750000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    8.750000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[    8.820000] PPP generic driver version 2.4.2
[    9.460000] ip_tables: (C) 2000-2006 Netfilter Core Team
[    9.580000] NET: Registered protocol family 24
[    9.600000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    9.610000] ehci-platform ehci-platform: Generic Platform EHCI Controller
[    9.610000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    9.650000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    9.670000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    9.670000] hub 1-0:1.0: USB hub found
[    9.670000] hub 1-0:1.0: 1 port detected
[    9.700000] nf_conntrack version 0.5.0 (460 buckets, 1840 max)
[    9.960000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    9.980000] uhci_hcd: USB Universal Host Controller Interface driver
[   10.000000] usb 1-1: new full-speed USB device number 2 using ehci-platform
[   10.230000] usbcore: registered new interface driver snd-usb-audio
[   17.170000] wlan0: authenticate with 54:e6:fc:30:f0:3e
[   17.180000] wlan0: send auth to 54:e6:fc:30:f0:3e (try 1/3)
[   17.190000] wlan0: authenticated
[   17.220000] wlan0: associate with 54:e6:fc:30:f0:3e (try 1/3)
[   17.220000] wlan0: RX AssocResp from 54:e6:fc:30:f0:3e (capab=0x431 status=0 aid=6)
[   17.230000] wlan0: associated
[ 1240.800000] wlan0: authenticate with 54:e6:fc:30:f0:3e
[ 1240.810000] wlan0: send auth to 54:e6:fc:30:f0:3e (try 1/3)
[ 1240.820000] wlan0: authenticated
[ 1240.840000] wlan0: associate with 54:e6:fc:30:f0:3e (try 1/3)
[ 1240.850000] wlan0: RX AssocResp from 54:e6:fc:30:f0:3e (capab=0x431 status=0 aid=6)
[ 1240.860000] wlan0: associated
[ 1555.500000] eth0: link up (100Mbps/Full duplex)
[ 1635.500000] eth0: link down
[ 1636.500000] eth0: link up (100Mbps/Full duplex)
	U-Boot 1.1.4 (Feb 28 2012 - 11:58:24)

	AP121 (ar9330) U-boot

	DRAM: 32 MB
	led turning on for 1s...
	id read 0x100000ff
	flash size 4194304, sector count = 64
	Flash: 4 MB
	Using default environment

	In: serial
	Out: serial
	Err: serial
	Net: ag7240_enet_initialize...
	No valid address in Flash. Using fixed address
	No valid address in Flash. Using fixed address
	: cfg1 0x5 cfg2 0x7114
	eth0: 00:03:7f:09:0b:ad
	ag7240_phy_setup
	eth0 up
	: cfg1 0xf cfg2 0x7214
	eth1: 00:03:7f:09:0b:ad
	athrs26_reg_init_lan
	ATHRS26: resetting s26
	ATHRS26: s26 reset done
	ag7240_phy_setup
	eth1 up
	eth0, eth1
	Autobooting in 1 seconds
	## Booting image at 9f020000 ...
	Uncompressing Kernel Image ... OK

	Starting kernel ...

	[ 0.000000] Linux version 3.3.8 (guoyong@guoyong-laptop) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #7 Sat Sep 1 20:49:34 CST 2012
	[ 0.000000] bootconsole [early0] enabled
	[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
	[ 0.000000] SoC: Atheros AR9330 rev 1
	[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
	[ 0.000000] Determined physical RAM map:
	[ 0.000000] memory: 02000000 @ 00000000 (usable)
	[ 0.000000] Initrd not found or empty - disabling initrd
	[ 0.000000] Zone PFN ranges:
	[ 0.000000] Normal 0x00000000 -> 0x00002000
	[ 0.000000] Movable zone start PFN for each node
	[ 0.000000] Early memory PFN ranges
	[ 0.000000] 0: 0x00000000 -> 0x00002000
	[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
	[ 0.000000] Kernel command line: board=TL-WR703N console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
	[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
	[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
	[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
	[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
	[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
	[ 0.000000] Writing ErrCtl register=00000000
	[ 0.000000] Readback ErrCtl register=00000000
	[ 0.000000] Memory: 29276k/32768k available (2082k kernel code, 3492k reserved, 396k data, 204k init, 0k highmem)
	[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
	[ 0.000000] NR_IRQS:51
	[ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
	[ 0.080000] pid_max: default: 32768 minimum: 301
	[ 0.080000] Mount-cache hash table entries: 512
	[ 0.090000] NET: Registered protocol family 16
	[ 0.090000] gpiochip_add: registered GPIOs 0 to 29 on device: ath79
	[ 0.100000] MIPS: machine is TP-LINK TL-WR703N v1
	[ 0.340000] bio: create slab <bio-0> at 0
	[ 0.350000] Switching to clocksource MIPS
	[ 0.350000] NET: Registered protocol family 2
	[ 0.360000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
	[ 0.360000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
	[ 0.360000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
	[ 0.370000] TCP: Hash tables configured (established 1024 bind 1024)
	[ 0.380000] TCP reno registered
	[ 0.380000] UDP hash table entries: 256 (order: 0, 4096 bytes)
	[ 0.390000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
	[ 0.390000] NET: Registered protocol family 1
	[ 0.420000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
	[ 0.420000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
	[ 0.430000] msgmni has been set to 57
	[ 0.430000] io scheduler noop registered
	[ 0.440000] io scheduler deadline registered (default)
	[ 0.440000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
	[ 0.450000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
	[ 0.450000] console [ttyATH0] enabled, bootconsole disabled
	[ 0.450000] console [ttyATH0] enabled, bootconsole disabled
	[ 0.470000] m25p80 spi0.0: found en25q32b, expected m25p80
	[ 0.470000] m25p80 spi0.0: en25q32b (4096 Kbytes)
	[ 0.480000] 5 tp-link partitions found on MTD device spi0.0
	[ 0.480000] Creating 5 MTD partitions on "spi0.0":
	[ 0.490000] 0x000000000000-0x000000020000 : "u-boot"
	[ 0.490000] 0x000000020000-0x0000000fd9b4 : "kernel"
	[ 0.500000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
	[ 0.510000] 0x0000000fd9b4-0x0000003f0000 : "rootfs"
	[ 0.510000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
	[ 0.530000] mtd: partition "rootfs" set to be root filesystem
	[ 0.530000] mtd: partition "rootfs_data" created automatically, ofs=380000, len=70000
	[ 0.540000] 0x000000380000-0x0000003f0000 : "rootfs_data"
	[ 0.550000] 0x0000003f0000-0x000000400000 : "art"
	[ 0.550000] 0x000000020000-0x0000003f0000 : "firmware"
	[ 0.580000] ag71xx_mdio: probed
	[ 0.580000] eth0: Atheros AG71xx at 0xb9000000, irq 4
	[ 1.130000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
	[ 1.140000] TCP cubic registered
	[ 1.140000] NET: Registered protocol family 17
	[ 1.150000] 8021q: 802.1Q VLAN Support v1.8
	[ 1.160000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
	[ 1.160000] Freeing unused kernel memory: 204k freed
	- preinit -
	Press the [f] key and hit [enter] to enter failsafe mode
	- regular preinit -
	[ 6.650000] JFFS2 notice: (404) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 7 of xref (0 dead, 0 orphan) found.
	switching to jffs2
	- init -

	Please press Enter to activate this console. [ 7.680000] Compat-wireless backport release: compat-wireless-2012-07-13
	[ 7.680000] Backport based on wireless-testing.git master-2012-07-16
	[ 7.690000] compat.git: wireless-testing.git
	[ 7.840000] cfg80211: Calling CRDA to update world regulatory domain
	[ 7.850000] cfg80211: World regulatory domain updated:
	[ 7.850000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
	[ 7.860000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
	[ 7.870000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
	[ 7.870000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
	[ 7.880000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
	[ 7.890000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
	[ 8.120000] usbcore: registered new interface driver usbfs
	[ 8.120000] usbcore: registered new interface driver hub
	[ 8.130000] usbcore: registered new device driver usb
	[ 8.690000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
	[ 8.700000] cfg80211: Calling CRDA for country: US
	[ 8.700000] cfg80211: Regulatory domain changed to country: US
	[ 8.710000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
	[ 8.720000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
	[ 8.730000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
	[ 8.730000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
	[ 8.740000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
	[ 8.750000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
	[ 8.750000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
	[ 8.820000] PPP generic driver version 2.4.2
	[ 9.460000] ip_tables: (C) 2000-2006 Netfilter Core Team
	[ 9.580000] NET: Registered protocol family 24
	[ 9.600000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
	[ 9.610000] ehci-platform ehci-platform: Generic Platform EHCI Controller
	[ 9.610000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
	[ 9.650000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
	[ 9.670000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
	[ 9.670000] hub 1-0:1.0: USB hub found
	[ 9.670000] hub 1-0:1.0: 1 port detected
	[ 9.700000] nf_conntrack version 0.5.0 (460 buckets, 1840 max)
	[ 9.960000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
	[ 9.980000] uhci_hcd: USB Universal Host Controller Interface driver
	[ 10.000000] usb 1-1: new full-speed USB device number 2 using ehci-platform
	[ 10.230000] usbcore: registered new interface driver snd-usb-audio
	[ 17.170000] wlan0: authenticate with 54:e6:fc:30:f0:3e
	[ 17.180000] wlan0: send auth to 54:e6:fc:30:f0:3e (try 1/3)
	[ 17.190000] wlan0: authenticated
	[ 17.220000] wlan0: associate with 54:e6:fc:30:f0:3e (try 1/3)
	[ 17.220000] wlan0: RX AssocResp from 54:e6:fc:30:f0:3e (capab=0x431 status=0 aid=6)
	[ 17.230000] wlan0: associated
	[ 1240.800000] wlan0: authenticate with 54:e6:fc:30:f0:3e
	[ 1240.810000] wlan0: send auth to 54:e6:fc:30:f0:3e (try 1/3)
	[ 1240.820000] wlan0: authenticated
	[ 1240.840000] wlan0: associate with 54:e6:fc:30:f0:3e (try 1/3)
	[ 1240.850000] wlan0: RX AssocResp from 54:e6:fc:30:f0:3e (capab=0x431 status=0 aid=6)
	[ 1240.860000] wlan0: associated
	[ 1555.500000] eth0: link up (100Mbps/Full duplex)
	[ 1635.500000] eth0: link down
	[ 1636.500000] eth0: link up (100Mbps/Full duplex)