Created
January 6, 2020 02:29
-
-
Save xeecos/f8d1b99a0602ee5c04893d1d1878b93a to your computer and use it in GitHub Desktop.
streamduino 3d printer settings for cura
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
[profile] | |
layer_height = 0.2 | |
wall_thickness = 0.8 | |
retraction_enable = True | |
solid_layer_thickness = 0.6 | |
fill_density = 40 | |
print_speed = 45 | |
print_temperature = 218 | |
print_temperature2 = 0 | |
print_temperature3 = 0 | |
print_temperature4 = 0 | |
print_temperature5 = 0 | |
print_bed_temperature = 50 | |
support = None | |
platform_adhesion = None | |
support_dual_extrusion = Both | |
wipe_tower = False | |
wipe_tower_volume = 15 | |
ooze_shield = False | |
filament_diameter = 1.75 | |
filament_diameter2 = 0 | |
filament_diameter3 = 0 | |
filament_diameter4 = 0 | |
filament_diameter5 = 0 | |
filament_flow = 100.0 | |
nozzle_size = 0.4 | |
retraction_speed = 60 | |
retraction_amount = 5 | |
retraction_dual_amount = 16.5 | |
retraction_min_travel = 1.5 | |
retraction_combing = All | |
retraction_minimal_extrusion = 0.02 | |
retraction_hop = 0.0 | |
bottom_thickness = 0.2 | |
layer0_width_factor = 100 | |
object_sink = 0.0 | |
overlap_dual = 0.15 | |
travel_speed = 80 | |
bottom_layer_speed = 18 | |
infill_speed = 45 | |
solidarea_speed = 40 | |
inset0_speed = 40 | |
insetx_speed = 45 | |
cool_min_layer_time = 5 | |
fan_enabled = True | |
skirt_line_count = 0 | |
skirt_gap = 3.0 | |
skirt_minimal_length = 150.0 | |
fan_full_height = 0.5 | |
fan_speed = 90 | |
fan_speed_max = 100 | |
cool_min_feedrate = 10 | |
cool_head_lift = False | |
solid_top = True | |
solid_bottom = True | |
fill_overlap = 15 | |
perimeter_before_infill = False | |
support_type = Lines | |
support_angle = 45 | |
support_fill_rate = 15 | |
support_xy_distance = 0.7 | |
support_z_distance = 0.15 | |
spiralize = False | |
simple_mode = False | |
brim_line_count = 10 | |
raft_margin = 5.0 | |
raft_line_spacing = 3.0 | |
raft_base_thickness = 0.3 | |
raft_base_linewidth = 1.0 | |
raft_interface_thickness = 0.27 | |
raft_interface_linewidth = 0.4 | |
raft_airgap_all = 0.0 | |
raft_airgap = 0.22 | |
raft_surface_layers = 2 | |
raft_surface_thickness = 0.27 | |
raft_surface_linewidth = 0.4 | |
fix_horrible_union_all_type_a = True | |
fix_horrible_union_all_type_b = False | |
fix_horrible_use_open_bits = False | |
fix_horrible_extensive_stitching = False | |
plugin_config = | |
object_center_x = -1 | |
object_center_y = -1 | |
[alterations] | |
start.gcode = ;Sliced at: {day} {date} {time} | |
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} | |
;Print time: {print_time} | |
;Filament used: {filament_amount}m {filament_weight}g | |
;Filament cost: {filament_cost} | |
;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line | |
;M109 S{print_temperature} ;Uncomment to add your own temperature line | |
G21 ;metric values | |
G90 ;absolute positioning | |
M82 ;set extruder to absolute mode | |
M107 ;start with the fan off | |
M300 | |
G28 ; home all axes | |
G1 X20 Y1 F3000 ; bring extruder to the front | |
G92 E0 ; zero the extruded length | |
G1 Z0.3 ; lower | |
G1 X35 E25 F225 ; purge nozzle with 30mm of filament | |
G1 X45 Y5 F2500 | |
G92 E0 ; zero the extruded length again | |
G1 F{travel_speed} | |
;Put printing message on LCD screen | |
M117 Printing... | |
end.gcode = ;End GCode | |
M104 S0 ;extruder heater off | |
M140 S0 ;heated bed heater off (if you have it) | |
G91 ;relative positioning | |
G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure | |
G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more | |
G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way | |
M84 ;steppers off | |
G90 ;absolute positioning | |
M300;{profile_string} | |
start2.gcode = ;Sliced at: {day} {date} {time} | |
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} | |
;Print time: {print_time} | |
;Filament used: {filament_amount}m {filament_weight}g | |
;Filament cost: {filament_cost} | |
;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line | |
;M104 S{print_temperature} ;Uncomment to add your own temperature line | |
;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line | |
;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line | |
G21 ;metric values | |
G90 ;absolute positioning | |
M107 ;start with the fan off | |
G28 X0 Y0 ;move X/Y to min endstops | |
G28 Z0 ;move Z to min endstops | |
G1 Z15.0 F{travel_speed} ;move the platform down 15mm | |
T1 ;Switch to the 2nd extruder | |
G92 E0 ;zero the extruded length | |
G1 F200 E10 ;extrude 10mm of feed stock | |
G92 E0 ;zero the extruded length again | |
G1 F200 E-{retraction_dual_amount} | |
T0 ;Switch to the first extruder | |
G92 E0 ;zero the extruded length | |
G1 F200 E10 ;extrude 10mm of feed stock | |
G92 E0 ;zero the extruded length again | |
G1 F{travel_speed} | |
;Put printing message on LCD screen | |
M117 Printing... | |
end2.gcode = ;End GCode | |
M104 T0 S0 ;extruder heater off | |
M104 T1 S0 ;extruder heater off | |
M140 S0 ;heated bed heater off (if you have it) | |
G91 ;relative positioning | |
G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure | |
G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more | |
G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way | |
M84 ;steppers off | |
G90 ;absolute positioning | |
;{profile_string} | |
start3.gcode = ;Sliced at: {day} {date} {time} | |
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} | |
;Print time: {print_time} | |
;Filament used: {filament_amount}m {filament_weight}g | |
;Filament cost: {filament_cost} | |
;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line | |
;M104 S{print_temperature} ;Uncomment to add your own temperature line | |
;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line | |
;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line | |
G21 ;metric values | |
G90 ;absolute positioning | |
M107 ;start with the fan off | |
G28 X0 Y0 ;move X/Y to min endstops | |
G28 Z0 ;move Z to min endstops | |
G1 Z15.0 F{travel_speed} ;move the platform down 15mm | |
T2 ;Switch to the 3rd extruder | |
G92 E0 ;zero the extruded length | |
G1 F200 E10 ;extrude 10mm of feed stock | |
G92 E0 ;zero the extruded length again | |
G1 F200 E-{retraction_dual_amount} | |
T1 ;Switch to the 2nd extruder | |
G92 E0 ;zero the extruded length | |
G1 F200 E10 ;extrude 10mm of feed stock | |
G92 E0 ;zero the extruded length again | |
G1 F200 E-{retraction_dual_amount} | |
T0 ;Switch to the first extruder | |
G92 E0 ;zero the extruded length | |
G1 F200 E10 ;extrude 10mm of feed stock | |
G92 E0 ;zero the extruded length again | |
G1 F{travel_speed} | |
;Put printing message on LCD screen | |
M117 Printing... | |
end3.gcode = ;End GCode | |
M104 T0 S0 ;extruder heater off | |
M104 T1 S0 ;extruder heater off | |
M104 T2 S0 ;extruder heater off | |
M140 S0 ;heated bed heater off (if you have it) | |
G91 ;relative positioning | |
G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure | |
G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more | |
G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way | |
M84 ;steppers off | |
G90 ;absolute positioning | |
;{profile_string} | |
start4.gcode = ;Sliced at: {day} {date} {time} | |
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} | |
;Print time: {print_time} | |
;Filament used: {filament_amount}m {filament_weight}g | |
;Filament cost: {filament_cost} | |
;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line | |
;M104 S{print_temperature} ;Uncomment to add your own temperature line | |
;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line | |
;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line | |
;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line | |
G21 ;metric values | |
G90 ;absolute positioning | |
M107 ;start with the fan off | |
G28 X0 Y0 ;move X/Y to min endstops | |
G28 Z0 ;move Z to min endstops | |
G1 Z15.0 F{travel_speed} ;move the platform down 15mm | |
T3 ;Switch to the 4th extruder | |
G92 E0 ;zero the extruded length | |
G1 F200 E10 ;extrude 10mm of feed stock | |
G92 E0 ;zero the extruded length again | |
G1 F200 E-{retraction_dual_amount} | |
T2 ;Switch to the 3rd extruder | |
G92 E0 ;zero the extruded length | |
G1 F200 E10 ;extrude 10mm of feed stock | |
G92 E0 ;zero the extruded length again | |
G1 F200 E-{retraction_dual_amount} | |
T1 ;Switch to the 2nd extruder | |
G92 E0 ;zero the extruded length | |
G1 F200 E10 ;extrude 10mm of feed stock | |
G92 E0 ;zero the extruded length again | |
G1 F200 E-{retraction_dual_amount} | |
T0 ;Switch to the first extruder | |
G92 E0 ;zero the extruded length | |
G1 F200 E10 ;extrude 10mm of feed stock | |
G92 E0 ;zero the extruded length again | |
G1 F{travel_speed} | |
;Put printing message on LCD screen | |
M117 Printing... | |
end4.gcode = ;End GCode | |
M104 T0 S0 ;extruder heater off | |
M104 T1 S0 ;extruder heater off | |
M104 T2 S0 ;extruder heater off | |
M104 T3 S0 ;extruder heater off | |
M140 S0 ;heated bed heater off (if you have it) | |
G91 ;relative positioning | |
G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure | |
G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more | |
G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way | |
M84 ;steppers off | |
G90 ;absolute positioning | |
;{profile_string} | |
support_start.gcode = | |
support_end.gcode = | |
cool_start.gcode = | |
cool_end.gcode = | |
replace.csv = | |
preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders. | |
;This code is added before the T(n) | |
postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders. | |
;This code is added after the T(n) | |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment