dataolle

#!/bin/bash
#set url and port to the xbmc box webservice
XBMC_HOST="http://127.0.0.1:8080"

if [ "$1" = "" ]; then
 echo -n "Insert URL: "
 read url
else
 url="$1"
fi

dankrause

#   Copyright 2014 Dan Krause
#
#   Licensed under the Apache License, Version 2.0 (the "License");
#   you may not use this file except in compliance with the License.
#   You may obtain a copy of the License at
#
#       http://www.apache.org/licenses/LICENSE-2.0
#
#   Unless required by applicable law or agreed to in writing, software
#   distributed under the License is distributed on an "AS IS" BASIS,

gbaman

Raspberry Pi Zero OTG Mode

Simple guide for setting up OTG modes on the Raspberry Pi Zero - By Andrew Mulholland (gbaman).

The Raspberry Pi Zero (and model A and A+) support USB On The Go, given the processor is connected directly to the USB port, unlike on the B, B+ or Pi 2 B, which goes via a USB hub.
Because of this, if setup to, the Pi can act as a USB slave instead, providing virtual serial (a terminal), virtual ethernet, virtual mass storage device (pendrive) or even other virtual devices like HID, MIDI, or act as a virtual webcam!
It is important to note that, although the model A and A+ can support being a USB slave, they are missing the ID pin (is tied to ground internally) so are unable to dynamically switch between USB master/slave mode. As such, they default to USB master mode. There is no easy way to change this right now.
It is also important to note, that a USB to UART serial adapter is not needed for any of these guides, as may be documented elsewhere across the int

gbaman

Setting up Pi Zero OTG - The quick way (No USB keyboard, mouse, HDMI monitor needed)

More details - http://blog.gbaman.info/?p=791

For this method, alongside your Pi Zero, MicroUSB cable and MicroSD card, only an additional computer is required, which can be running Windows (with Bonjour, iTunes or Quicktime installed), Mac OS or Linux (with Avahi Daemon installed, for example Ubuntu has it built in).
1. Flash Raspbian Jessie full or Raspbian Jessie Lite onto the SD card.
2. Once Raspbian is flashed, open up the boot partition (in Windows Explorer, Finder etc) and add to the bottom of the config.txt file dtoverlay=dwc2 on a new line, then save the file.
3. If using a recent release of Jessie (Dec 2016 onwards), then create a new file simply called ssh in the SD card as well. By default SSH i

braian87b

# ========================================================
# Setup a Dumb AP, Wired backbone for OpenWRT / LEDE
# ========================================================
# Set lan logical interface as bridge (to allow bridge multiple physical interfaces)
uci set network.lan.type='bridge'
# assign WAN physical interface to LAN (will be available as an additional LAN port now)
uci set network.lan.ifname="$(uci get network.lan.ifname) $(uci get network.wan.ifname)"
uci del network.wan.ifname
# Remove wan logical interface, since we will not need it.
uci del network.wan

mirhec

Setup Gitea on Raspberry Pi (3)

These instructions are based on this article: https://www.alexruf.net/2016/05/23/setup-gogs-git-service.html.

Setup Raspberry Pi with minimal Raspbian image. You need to connect to the HDMI port and set the following:

sudo raspi-config

There you need to enable the SSH server and you should change the hostname.

joeljacobs

Below are single-line commands to run in BASH on a Raspberry Pi to rewrite the toner chips to "full" for a Ricoh SP C250DN Printer.

You will need to have the 4 files below in the same directory: "black" "cyan" "magenta" and "yellow". 
The chip is near one edge of the cartridge. The pad closest to the edge is GND, followed by VCC, DATA, and Clock.
On the Pi, connect VCC and GND to +3.3V and GND. Connect Data to (physical numbering) 3 and 5. They are the I2C Data and Clock pins.

Be sure i2c is enabled and installed. 
modprobe -r i2c_bcm2708 ;modprobe i2c_bcm2708 baudrate=9600

Tustin

import discord
import asyncio
import requests
import json

client = discord.Client()

def check_psn(psn):
    response = requests.post('https://accounts.api.playstation.com/api/v1/accounts/onlineIds', json={"onlineId": psn, "reserveIfAvailable": False})
    return response.status_code != 401 and response.status_code != 400

moorer2k

#DietPi setup script for RTL-SDR/Multimon-ng/Pagermon for decoding pager messages(FLEX/POCSAG etc.)

cat <<EOF >no-rtl.conf
blacklist dvb_usb_rtl28xxu
blacklist rtl2832
blacklist rtl2830
EOF

mv no-rtl.conf /etc/modprobe.d/

pigeonhill

--Neutral Density Script (NDS) Release 0.9M

--[[
********************************************************************************************
This script creates a bracket set for post processing, allowing you to simulate an ND filter. 
Also you can use the script to create brackets to 'remove people' ;-)

Change the number of brackets or the time delay (s) between brackets using the MENU and PLAY keys (Green text)

Toggle between these changes with the UP key.