Slic3r 1.2.9 configuration for FoldaRap

FoldaRap - 1.2.9.ini

# generated by Slic3r 1.2.9 on Mon Feb 15 00:27:19 2016
avoid_crossing_perimeters = 0
bed_shape = 0x0,140x0,140x140,0x140
bed_temperature = 0
before_layer_gcode = 
bottom_solid_layers = 2
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 40
brim_width = 0
complete_objects = 0
cooling = 1
default_acceleration = 0
disable_fan_first_layers = 1
dont_support_bridges = 1
duplicate_distance = 6
end_gcode = M200 D0 T0 ; turn off volumetric E;\nM104 S0 ; turn off temperature\nM140 S0 ; turn off temperature\nG1 X140 Y140 F3600 ; show print\nM84     ; disable motors\n
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 40
external_perimeters_first = 1
extra_perimeters = 0
extruder_clearance_height = 150
extruder_clearance_radius = 16
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0.55
fan_always_on = 0
fan_below_layer_time = 30
filament_colour = #000000
filament_diameter = 1.75
fill_angle = 45
fill_density = 25%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_bed_temperature = 0
first_layer_extrusion_width = 0
first_layer_height = 0.25
first_layer_speed = 60%
first_layer_temperature = 0
gap_fill_speed = 20
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 10%
infill_speed = 60
interface_shells = 0
layer_gcode = 
layer_height = 0.25
max_fan_speed = 50
max_print_speed = 80
max_volumetric_speed = 10.8
min_fan_speed = 35
min_print_speed = 20
min_skirt_length = 20
notes = 
nozzle_diameter = 0.5
octoprint_apikey = 
octoprint_host = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 50
perimeters = 2
post_process = 
pressure_advance = 0
raft_layers = 0
resolution = 0
retract_before_travel = 2
retract_layer_change = 1
retract_length = 3
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 45
seam_position = nearest
skirt_distance = 3
skirt_height = 1
skirts = 1
slowdown_below_layer_time = 15
small_perimeter_speed = 30
solid_infill_below_area = 15
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 50
spiral_vase = 0
standby_temperature_delta = -5
start_gcode = M200 D[filament_diameter_0] T0 ; volumetric E\nG28 ; home all axes\n
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.1
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 40
support_material_pattern = honeycomb
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 45
temperature = 0
thin_walls = 1
threads = 2
toolchange_gcode = 
top_infill_extrusion_width = 0
top_solid_infill_speed = 40
top_solid_layers = 2
travel_speed = 250
use_firmware_retraction = 1
use_relative_e_distances = 0
use_volumetric_e = 1
vibration_limit = 0
wipe = 0
xy_size_compensation = 0
z_offset = 0