Created
June 21, 2018 00:47
-
-
Save xypron/34b6485deabfc8172f978b5a99705466 to your computer and use it in GitHub Desktop.
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
DDR Version 1.08 20170320 | |
In | |
Channel 0: DDR3, 800MHz | |
Bus Width=32 Col=10 Bank=8 Row=15/15 CS=2 Die Bus-Width=16 Size=2048MB | |
Channel 1: DDR3, 800MHz | |
Bus Width=32 Col=10 Bank=8 Row=15/15 CS=2 Die Bus-Width=16 Size=2048MB | |
256B stride | |
ch 0 ddrconfig = 0x101, ddrsize = 0x2020 | |
ch 1 ddrconfig = 0x101, ddrsize = 0x2020 | |
pmugrf_os_reg[2] = 0x3AA17AA1, stride = 0xD | |
OUT | |
Boot1: 2017-04-07, version: 1.06 | |
CPUId = 0x0 | |
ChipType = 0x10, 1824 | |
mmc: ERROR: SDHCI ERR:cmd:0x102,stat:0x18000 | |
mmc: ERROR: Card did not respond to voltage select! | |
emmc reinit | |
mmc: ERROR: SDHCI ERR:cmd:0x102,stat:0x18000 | |
mmc: ERROR: Card did not respond to voltage select! | |
emmc reinit | |
mmc: ERROR: SDHCI ERR:cmd:0x102,stat:0x18000 | |
mmc: ERROR: Card did not respond to voltage select! | |
SdmmcInit=2 1 | |
SdmmcInit=0 0 | |
BootCapSize=0 | |
UserCapSize=30147MB | |
FwPartOffset=2000 , 0 | |
StorageInit ok = 57813 | |
LoadTrustBL | |
No find bl30.bin | |
No find bl32.bin | |
RunBL31 0x10000 | |
NOTICE: BL31: v1.3(debug):55aa0b4 | |
NOTICE: BL31: Built : 16:55:03, Mar 31 2017 | |
INFO: GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3 | |
INFO: boot cpu mask: 0 | |
INFO: plat_rockchip_pmu_init(1089): pd status 3e | |
INFO: BL31: Initializing runtime services | |
INFO: BL31: Preparing for EL3 exit to normal world | |
INFO: Entry point address = 0x200000 | |
INFO: SPSR = 0x3c9 | |
U-Boot 2018.05 (Jun 21 2018 - 02:33:12 +0200) | |
Model: Firefly-RK3399 Board | |
DRAM: 3.9 GiB | |
MMC: dwmmc@fe320000: 1, sdhci@fe330000: 0 | |
Loading Environment from MMC... *** Warning - bad CRC, using default environment | |
Failed (-5) | |
In: serial@ff1a0000 | |
Out: serial@ff1a0000 | |
Err: serial@ff1a0000 | |
Model: Firefly-RK3399 Board | |
Net: | |
Error: ethernet@fe300000 address not set. | |
No ethernet found. | |
Hit any key to stop autoboot: 0 | |
=> | |
=> | |
=> | |
=> load mmc 1:1 ${fdt_addr_r} 2018-06-20/rk3399-firefly.dtb | |
53263 bytes read in 8 ms (6.3 MiB/s) | |
=> load mmc 1:1 ${kernel_addr_r} 2018-06-20/Image | |
18426368 bytes read in 1157 ms (15.2 MiB/s) | |
=> booti ${kernel_addr_r} - ${fdt_addr_r} | |
## Flattened Device Tree blob at 01f00000 | |
Booting using the fdt blob at 0x1f00000 | |
Loading Device Tree to 00000000f5f09000, end 00000000f5f1900e ... OK | |
Starting kernel ... | |
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] | |
[ 0.000000] Linux version 4.18.0-rc1-next-20180620 (buildslave@Ubuntu-1604-xenial-64-minimal) (8 | |
[ 0.000000] Machine model: Firefly-RK3399 Board | |
[ 0.000000] efi: Getting EFI parameters from FDT: | |
[ 0.000000] efi: UEFI not found. | |
[ 0.000000] cma: Reserved 32 MiB at 0x00000000f6000000 | |
[ 0.000000] NUMA: No NUMA configuration found | |
[ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x00000000f7ffffff] | |
[ 0.000000] NUMA: NODE_DATA [mem 0xf5fa8640-0xf5fa9dff] | |
[ 0.000000] Zone ranges: | |
[ 0.000000] DMA32 [mem 0x0000000000200000-0x00000000f7ffffff] | |
[ 0.000000] Normal empty | |
[ 0.000000] Movable zone start for each node | |
[ 0.000000] Early memory node ranges | |
[ 0.000000] node 0: [mem 0x0000000000200000-0x00000000f7ffffff] | |
[ 0.000000] Initmem setup node 0 [mem 0x0000000000200000-0x00000000f7ffffff] | |
[ 0.000000] psci: probing for conduit method from DT. | |
[ 0.000000] psci: PSCIv1.0 detected in firmware. | |
[ 0.000000] psci: Using standard PSCI v0.2 function IDs | |
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported. | |
[ 0.000000] psci: SMC Calling Convention v1.0 | |
[ 0.000000] random: get_random_bytes called from start_kernel+0xac/0x414 with crng_init=0 | |
[ 0.000000] percpu: Embedded 23 pages/cpu @(____ptrval____) s56000 r8192 d30016 u94208 | |
[ 0.000000] Detected VIPT I-cache on CPU0 | |
[ 0.000000] CPU features: detected: Kernel page table isolation (KPTI) | |
[ 0.000000] CPU features: enabling workaround for ARM erratum 845719 | |
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 999432 | |
[ 0.000000] Policy zone: DMA32 | |
[ 0.000000] Kernel command line: | |
[ 0.000000] Memory: 3943500K/4061184K available (10364K kernel code, 1354K rwdata, 4952K rodata) | |
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1 | |
[ 0.000000] rcu: Preemptible hierarchical RCU implementation. | |
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=6. | |
[ 0.000000] Tasks RCU enabled. | |
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=6 | |
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 | |
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode | |
[ 0.000000] GICv3: Distributor has no Range Selector support | |
[ 0.000000] GICv3: no VLPI support, no direct LPI support | |
[ 0.000000] ITS [mem 0xfee20000-0xfee3ffff] | |
[ 0.000000] ITS@0x00000000fee20000: allocated 65536 Devices @f1880000 (flat, esz 8, psz 64K, sh) | |
[ 0.000000] ITS: using cache flushing for cmd queue | |
[ 0.000000] GIC: using LPI property table @0x00000000f1840000 | |
[ 0.000000] ITS: Allocated 1792 chunks for LPIs | |
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000fef00000 | |
[ 0.000000] CPU0: using LPI pending table @0x00000000f1850000 | |
[ 0.000000] GIC: using cache flushing for LPI property table | |
[ 0.000000] GICv3: GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0[0] /cpus/cpu@1[1] } | |
[ 0.000000] GICv3: GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@100[4] /cpus/cpu@101} | |
[ 0.000000] rockchip_mmc_get_phase: invalid clk rate | |
[ 0.000000] rockchip_mmc_get_phase: invalid clk rate | |
[ 0.000000] rockchip_mmc_get_phase: invalid clk rate | |
[ 0.000000] rockchip_mmc_get_phase: invalid clk rate | |
[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). | |
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_s | |
[ 0.000009] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns | |
[ 0.002548] Console: colour dummy device 80x25 | |
[ 0.003825] console [tty0] enabled | |
[ 0.003941] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 Bo) | |
[ 0.003998] pid_max: default: 32768 minimum: 301 | |
[ 0.004178] Security Framework initialized | |
[ 0.007239] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) | |
[ 0.008794] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) | |
[ 0.008932] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) | |
[ 0.009015] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes) | |
[ 0.031813] ASID allocator initialised with 32768 entries | |
[ 0.035819] rcu: Hierarchical SRCU implementation. | |
[ 0.039962] Platform MSI: interrupt-controller@fee20000 domain created | |
[ 0.040498] PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created | |
[ 0.047359] EFI services will not be available. | |
[ 0.048507] smp: Bringing up secondary CPUs ... | |
[ 0.068718] Detected VIPT I-cache on CPU1 | |
[ 0.068769] GICv3: CPU1: found redistributor 1 region 0:0x00000000fef20000 | |
[ 0.068827] CPU1: using LPI pending table @0x00000000f0c50000 | |
[ 0.068885] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] | |
[ 0.088801] Detected VIPT I-cache on CPU2 | |
[ 0.088841] GICv3: CPU2: found redistributor 2 region 0:0x00000000fef40000 | |
[ 0.088898] CPU2: using LPI pending table @0x00000000f0c80000 | |
[ 0.088941] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] | |
[ 0.108904] Detected VIPT I-cache on CPU3 | |
[ 0.108945] GICv3: CPU3: found redistributor 3 region 0:0x00000000fef60000 | |
[ 0.109000] CPU3: using LPI pending table @0x00000000f0ca0000 | |
[ 0.109042] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] | |
[ 0.131693] CPU features: enabling workaround for EL2 vector hardening | |
[ 0.132060] Detected PIPT I-cache on CPU4 | |
[ 0.133294] GICv3: CPU4: found redistributor 100 region 0:0x00000000fef80000 | |
[ 0.135799] CPU4: using LPI pending table @0x00000000f0cd0000 | |
[ 0.137093] CPU4: Booted secondary processor 0x0000000100 [0x410fd082] | |
[ 0.163208] Detected PIPT I-cache on CPU5 | |
[ 0.164417] GICv3: CPU5: found redistributor 101 region 0:0x00000000fefa0000 | |
[ 0.166915] CPU5: using LPI pending table @0x00000000f0d00000 | |
[ 0.168062] CPU5: Booted secondary processor 0x0000000101 [0x410fd082] | |
[ 0.173093] smp: Brought up 1 node, 6 CPUs | |
[ 0.173765] SMP: Total of 6 processors activated. | |
[ 0.173813] CPU features: detected: GIC system register CPU interface | |
[ 0.173849] CPU features: detected: 32-bit EL0 Support | |
[ 0.258075] CPU: All CPU(s) started at EL2 | |
[ 0.258643] alternatives: patching kernel code | |
[ 0.265161] devtmpfs: initialized | |
[ 0.288387] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041s | |
[ 0.288746] futex hash table entries: 2048 (order: 5, 131072 bytes) | |
[ 0.291888] pinctrl core: initialized pinctrl subsystem | |
[ 0.297569] DMI not present or invalid. | |
[ 0.299593] NET: Registered protocol family 16 | |
[ 0.302300] audit: initializing netlink subsys (disabled) | |
[ 0.304506] audit: type=2000 audit(0.296:1): state=initialized audit_enabled=0 res=1 | |
[ 0.309040] cpuidle: using governor menu | |
[ 0.310022] vdso: 2 pages (1 code @ (____ptrval____), 1 data @ (____ptrval____)) | |
[ 0.310259] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. | |
[ 0.323143] DMA: preallocated 256 KiB pool for atomic allocations | |
[ 0.328210] Serial: AMBA PL011 UART driver | |
[ 0.443780] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages | |
[ 0.446688] cryptd: max_cpu_qlen set to 1000 | |
[ 0.451087] ACPI: Interpreter disabled. | |
[ 0.456793] vcc3v3_pcie: supplied by dc_12v | |
[ 0.459246] vcc_sys: supplied by dc_12v | |
[ 0.465191] vgaarb: loaded | |
[ 0.466218] SCSI subsystem initialized | |
[ 0.468444] usbcore: registered new interface driver usbfs | |
[ 0.468612] usbcore: registered new interface driver hub | |
[ 0.468937] usbcore: registered new device driver usb | |
[ 0.472590] pps_core: LinuxPPS API ver. 1 registered | |
[ 0.472811] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linu> | |
[ 0.472989] PTP clock support registered | |
[ 0.473504] EDAC MC: Ver: 3.0.0 | |
[ 0.480397] Advanced Linux Sound Architecture Driver Initialized. | |
[ 0.484540] clocksource: Switched to clocksource arch_sys_counter | |
[ 0.485428] VFS: Disk quotas dquot_6.6.0 | |
[ 0.485591] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) | |
[ 0.485925] pnp: PnP ACPI: disabled | |
[ 0.507753] NET: Registered protocol family 2 | |
[ 0.510036] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes) | |
[ 0.510382] TCP established hash table entries: 32768 (order: 6, 262144 bytes) | |
[ 0.511316] TCP bind hash table entries: 32768 (order: 7, 524288 bytes) | |
[ 0.513326] TCP: Hash tables configured (established 32768 bind 32768) | |
[ 0.514012] UDP hash table entries: 2048 (order: 4, 65536 bytes) | |
[ 0.514316] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) | |
[ 0.514870] NET: Registered protocol family 1 | |
[ 0.518905] RPC: Registered named UNIX socket transport module. | |
[ 0.518948] RPC: Registered udp transport module. | |
[ 0.518975] RPC: Registered tcp transport module. | |
[ 0.519000] RPC: Registered tcp NFSv4.1 backchannel transport module. | |
[ 0.527331] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available | |
[ 0.530179] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available | |
[ 0.531248] kvm [1]: 8-bit VMID | |
[ 0.533696] kvm [1]: vgic-v2@fff20000 | |
[ 0.534851] kvm [1]: GIC system register CPU interface enabled | |
[ 0.537636] kvm [1]: vgic interrupt IRQ10 | |
[ 0.539924] kvm [1]: Hyp mode initialized successfully | |
[ 0.552761] Initialise system trusted keyrings | |
[ 0.553534] workingset: timestamp_bits=45 max_order=20 bucket_order=0 | |
[ 0.573445] squashfs: version 4.0 (2009/01/31) Phillip Lougher | |
[ 0.575913] NFS: Registering the id_resolver key type | |
[ 0.576326] Key type id_resolver registered | |
[ 0.576361] Key type id_legacy registered | |
[ 0.576412] nfs4filelayout_init: NFSv4 File Layout Driver Registering... | |
[ 0.576911] 9p: Installing v9fs 9p2000 file system support | |
[ 0.577181] pstore: using deflate compression | |
[ 0.598433] Key type asymmetric registered | |
[ 0.598694] Asymmetric key parser 'x509' registered | |
[ 0.599615] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) | |
[ 0.599680] io scheduler noop registered | |
[ 0.599707] io scheduler deadline registered | |
[ 0.600720] io scheduler cfq registered (default) | |
[ 0.600763] io scheduler mq-deadline registered | |
[ 0.600792] io scheduler kyber registered | |
[ 0.613699] vcc5v0_host: supplied by vcc_sys | |
[ 0.650579] EINJ: ACPI disabled. | |
[ 0.675195] dma-pl330 ff6d0000.dma-controller: Loaded driver for PL330 DMAC-241330 | |
[ 0.675575] dma-pl330 ff6d0000.dma-controller: DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Nu2 | |
[ 0.683164] dma-pl330 ff6e0000.dma-controller: Loaded driver for PL330 DMAC-241330 | |
[ 0.683516] dma-pl330 ff6e0000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 N6 | |
[ 0.695429] pwm-regulator: supplied by regulator-dummy | |
[ 0.696727] vcc3v3_sys: supplied by vcc_sys | |
[ 0.709257] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled | |
[ 0.715510] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 37, base_baud = 1500000) is a 1655A | |
[ 0.718477] ff1a0000.serial: ttyS2 at MMIO 0xff1a0000 (irq = 38, base_baud = 1500000) is a 1655A | |
[ 0.809023] console [ttyS2] enabled | |
[ 0.813526] SuperH (H)SCI(F) driver initialized | |
[ 0.815572] msm_serial: driver initialized | |
[ 0.818906] cacheinfo: Unable to detect cache hierarchy for CPU 0 | |
[ 0.838655] loop: module loaded | |
[ 0.855150] libphy: Fixed MDIO Bus: probed | |
[ 0.857234] tun: Universal TUN/TAP device driver, 1.6 | |
[ 0.861909] thunder_xcv, ver 1.0 | |
[ 0.862650] thunder_bgx, ver 1.0 | |
[ 0.863117] nicpf, ver 1.0 | |
[ 0.865225] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k | |
[ 0.865801] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. | |
[ 0.866497] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k | |
[ 0.867142] igb: Copyright (c) 2007-2014 Intel Corporation. | |
[ 0.867799] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k | |
[ 0.868581] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. | |
[ 0.870329] sky2: driver version 1.30 | |
[ 0.873515] VFIO - User Level meta-driver version: 0.3 | |
[ 0.878864] dwc3 fe800000.dwc3: Failed to get clk 'ref': -2 | |
[ 0.891630] OF: graph: no port node found in /syscon@ff770000/usb2-phy@e450/otg-port | |
[ 0.898810] dwc3 fe900000.dwc3: Failed to get clk 'ref': -2 | |
[ 0.910411] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver | |
[ 0.911218] ehci-pci: EHCI PCI platform driver | |
[ 0.911768] ehci-platform: EHCI generic platform driver | |
[ 0.914980] ehci-platform fe380000.usb: EHCI Host Controller | |
[ 0.915560] ehci-platform fe380000.usb: new USB bus registered, assigned bus number 1 | |
[ 0.918806] ehci-platform fe380000.usb: irq 30, io mem 0xfe380000 | |
[ 0.932125] ehci-platform fe380000.usb: USB 2.0 started, EHCI 1.00 | |
[ 0.934376] hub 1-0:1.0: USB hub found | |
[ 0.934809] hub 1-0:1.0: 1 port detected | |
[ 0.939166] ehci-platform fe3c0000.usb: EHCI Host Controller | |
[ 0.939769] ehci-platform fe3c0000.usb: new USB bus registered, assigned bus number 2 | |
[ 0.943504] ehci-platform fe3c0000.usb: irq 32, io mem 0xfe3c0000 | |
[ 0.960144] ehci-platform fe3c0000.usb: USB 2.0 started, EHCI 1.00 | |
[ 0.962173] hub 2-0:1.0: USB hub found | |
[ 0.962580] hub 2-0:1.0: 1 port detected | |
[ 0.964467] ehci-orion: EHCI orion driver | |
[ 0.965360] ehci-exynos: EHCI EXYNOS driver | |
[ 0.966136] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver | |
[ 0.966762] ohci-pci: OHCI PCI platform driver | |
[ 0.967308] ohci-platform: OHCI generic platform driver | |
[ 0.968512] ohci-platform fe3a0000.usb: Generic Platform OHCI controller | |
[ 0.969176] ohci-platform fe3a0000.usb: new USB bus registered, assigned bus number 3 | |
[ 0.972156] ohci-platform fe3a0000.usb: irq 31, io mem 0xfe3a0000 | |
[ 1.037935] hub 3-0:1.0: USB hub found | |
[ 1.038369] hub 3-0:1.0: 1 port detected | |
[ 1.040952] ohci-platform fe3e0000.usb: Generic Platform OHCI controller | |
[ 1.041699] ohci-platform fe3e0000.usb: new USB bus registered, assigned bus number 4 | |
[ 1.043848] ohci-platform fe3e0000.usb: irq 33, io mem 0xfe3e0000 | |
[ 1.109533] hub 4-0:1.0: USB hub found | |
[ 1.109947] hub 4-0:1.0: 1 port detected | |
[ 1.111683] ohci-exynos: OHCI EXYNOS driver | |
[ 1.114036] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller | |
[ 1.114657] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 5 | |
[ 1.118440] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x000000000 | |
[ 1.119440] xhci-hcd xhci-hcd.0.auto: irq 218, io mem 0xfe800000 | |
[ 1.122266] hub 5-0:1.0: USB hub found | |
[ 1.122683] hub 5-0:1.0: 1 port detected | |
[ 1.123947] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller | |
[ 1.124631] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 6 | |
[ 1.125361] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed | |
[ 1.126096] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM. | |
[ 1.128341] hub 6-0:1.0: USB hub found | |
[ 1.128752] hub 6-0:1.0: 1 port detected | |
[ 1.130238] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller | |
[ 1.130797] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 7 | |
[ 1.138658] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x000000000 | |
[ 1.139742] xhci-hcd xhci-hcd.1.auto: irq 219, io mem 0xfe900000 | |
[ 1.142488] hub 7-0:1.0: USB hub found | |
[ 1.142943] hub 7-0:1.0: 1 port detected | |
[ 1.144270] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller | |
[ 1.144816] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 8 | |
[ 1.145546] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed | |
[ 1.146299] usb usb8: We don't know the algorithms for LPM for this host, disabling LPM. | |
[ 1.148471] hub 8-0:1.0: USB hub found | |
[ 1.148886] hub 8-0:1.0: 1 port detected | |
[ 1.151345] usbcore: registered new interface driver usb-storage | |
[ 1.163391] i2c /dev entries driver | |
[ 1.175877] rk808 0-001b: chip id: 0x0 | |
[ 1.183420] rk808-regulator rk808-regulator: there is no dvs0 gpio | |
[ 1.184448] rk808-regulator rk808-regulator: there is no dvs1 gpio | |
[ 1.185136] DCDC_REG1: supplied by vcc_sys | |
[ 1.186955] DCDC_REG2: supplied by vcc_sys | |
[ 1.188331] DCDC_REG3: supplied by vcc_sys | |
[ 1.189151] DCDC_REG4: supplied by vcc_sys | |
[ 1.190393] LDO_REG1: supplied by vcc_sys | |
[ 1.192447] LDO_REG2: supplied by vcc_sys | |
[ 1.193103] vcc2v8_dvp: Bringing 3000000uV into 2800000-2800000uV | |
[ 1.194860] LDO_REG3: supplied by vcc_sys | |
[ 1.196913] LDO_REG4: supplied by vcc_sys | |
[ 1.198729] LDO_REG5: supplied by vcc_sys | |
[ 1.200476] LDO_REG6: supplied by vcc_sys | |
[ 1.202344] LDO_REG7: supplied by vcc_sys | |
[ 1.204122] LDO_REG8: supplied by vcc_sys | |
[ 1.205917] SWITCH_REG1: supplied by vcc3v3_sys | |
[ 1.206965] SWITCH_REG2: supplied by vcc3v3_sys | |
[ 1.209844] fan53555-regulator 0-0040: FAN53555 Option[8] Rev[1] Detected! | |
[ 1.210624] fan53555-reg: supplied by vcc_sys | |
[ 1.212990] vcc1v8_s3: supplied by vcc_1v8 | |
[ 1.214536] fan53555-regulator 0-0041: FAN53555 Option[8] Rev[1] Detected! | |
[ 1.215213] fan53555-reg: supplied by vcc_sys | |
[ 1.237397] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 400000 KHz | |
[ 1.238608] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 408000 KHz | |
[ 1.241234] cpufreq: cpufreq_online: CPU4: Running at unlisted freq: 12000 KHz | |
[ 1.242436] random: fast init done | |
[ 1.243407] cpufreq: cpufreq_online: CPU4: Unlisted initial frequency changed to: 408000 KHz | |
[ 1.246350] sdhci: Secure Digital Host Controller Interface driver | |
[ 1.246903] sdhci: Copyright(c) Pierre Ossman | |
[ 1.247577] Synopsys Designware Multimedia Card Interface Driver | |
[ 1.249197] dwmmc_rockchip fe320000.dwmmc: IDMAC supports 32-bit address mode. | |
[ 1.250029] dwmmc_rockchip fe320000.dwmmc: Using internal DMA controller. | |
[ 1.250635] dwmmc_rockchip fe320000.dwmmc: Version ID is 270a | |
[ 1.251183] dwmmc_rockchip fe320000.dwmmc: DW MMC controller at irq 28,32 bit host data width,2o | |
[ 1.252136] dwmmc_rockchip fe320000.dwmmc: Got CD GPIO | |
[ 1.265434] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ di) | |
[ 1.279661] sdhci-pltfm: SDHCI platform and OF driver helper | |
[ 1.281169] mmc1: CQHCI version 5.10 | |
[ 1.296010] usb 2-1: new high-speed USB device number 2 using ehci-platform | |
[ 1.305689] mmc1: SDHCI controller on fe330000.sdhci [fe330000.sdhci] using ADMA | |
[ 1.307657] ledtrig-cpu: registered to indicate activity on CPUs | |
[ 1.309097] usbcore: registered new interface driver usbhid | |
[ 1.309599] usbhid: USB HID core driver | |
[ 1.312994] NET: Registered protocol family 17 | |
[ 1.313460] 9pnet: Installing 9P2000 support | |
[ 1.313888] Key type dns_resolver registered | |
[ 1.314609] registered taskstats version 1 | |
[ 1.314984] Loading compiled-in X.509 certificates | |
[ 1.315482] Unable to create integrity sysfs dir: -19 | |
[ 1.316125] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 5000000) | |
[ 1.317036] mmc0: new high speed SDHC card at address 59b4 | |
[ 1.318241] mmcblk0: mmc0:59b4 SD 29.4 GiB | |
[ 1.320071] mmcblk0: p1 p2 p3 p4 | |
[ 1.332415] hctosys: unable to open rtc device (rtc0) | |
[ 1.333733] ALSA device list: | |
[ 1.334006] No soundcards found. | |
[ 1.334538] ttyS2 - failed to request DMA | |
[ 1.335047] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6 | |
[ 1.335707] Please append a correct "root=" boot option; here are the available partitions: | |
[ 1.336468] b300 30870528 mmcblk0 | |
[ 1.336471] driver: mmcblk | |
[ 1.337078] b301 1048576 mmcblk0p1 4747d4a2-01 | |
[ 1.337079] | |
[ 1.337683] b302 1048576 mmcblk0p2 4747d4a2-02 | |
[ 1.337684] | |
[ 1.338288] b303 28756992 mmcblk0p3 4747d4a2-03 | |
[ 1.338289] | |
[ 1.338893] b304 15360 mmcblk0p4 4747d4a2-04 | |
[ 1.338895] | |
[ 1.339499] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) | |
[ 1.340229] CPU: 3 PID: 1 Comm: swapper/0 Not tainted 4.18.0-rc1-next-20180620 #1 | |
[ 1.340887] Hardware name: Firefly-RK3399 Board (DT) | |
[ 1.341326] Call trace: | |
[ 1.341552] dump_backtrace+0x0/0x150 | |
[ 1.341881] show_stack+0x14/0x20 | |
[ 1.342179] dump_stack+0x8c/0xb0 | |
[ 1.342478] panic+0x124/0x290 | |
[ 1.342754] mount_block_root+0x190/0x278 | |
[ 1.343111] mount_root+0x140/0x174 | |
[ 1.343421] prepare_namespace+0x13c/0x184 | |
[ 1.343786] kernel_init_freeable+0x21c/0x258 | |
[ 1.344175] kernel_init+0x10/0x108 | |
[ 1.344487] ret_from_fork+0x10/0x1c | |
[ 1.344809] SMP: stopping secondary CPUs | |
[ 1.345158] Kernel Offset: disabled | |
[ 1.345468] CPU features: 0x2180600c | |
[ 1.345785] Memory Limit: none | |
[ 1.346063] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(- |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment