Modix BIG-60 v4 Corrected Configuration

config.g

; Modix Big-60, Generation 4, Single Printhead
; Configuration file for Duet WiFi (firmware version 3.4.5)
; Generated by Modix - Version 3.4.5 Config B 
global config_version = "Version 3.4.5 Config B"
global generation = 4   ; Generation 4 printer
global printhead = 1  ; Griffin printhead
global printheads = 1 ; single printhead
global idex = 0     ; no IDEX
global expansion = 1  ; Griffin expansion board is installed

; General preferences_________________________________________________________
G90                             ; send absolute coordinates...
M83                             ; ...but relative extruder moves
M555 P2                           ; Set output to look like Marlin
M575 P1 B57600 S1                     ; Set auxiliary serial port baud rate and require checksum (for PanelDue)

; Network_____________________________________________________________________
M550 P"Big 60 V4"                     ; set printer name
;M551 P"MODIX3D"                      ; Set password (optional)
M98 P"config_networking.g"                  ; enable network
G4 P300                           ; wait 300ms
;M552 P0.0.0.0                        ; Uncomment this command for using Duet Ethernet board

; Drives_________________________________________________________________________
;Main board______________________________________________________________________
M569 P0 S1                          ; Physical drive 0. X-B-M
M569 P1 S0                          ; Physical drive 1. X-F-M
M569 P2 R-1                         ; Physical drive 2. disabled
M569 P3 S0                          ; Physical drive 3 goes backwards. E0-Extruder.
M569 P4 R-1                         ; Physical drive 4. disabled
;Duex5 board_____________________________________________________________________
M569 P5 S0                          ; Physical drive 5. Y
M569 P6 S1                          ; Physical drive 6. Z-B-L (0,600)
M569 P7 S1                          ; Physical drive 7. Z-F-L (0,0) 
M569 P8 S1                          ; Physical drive 8. Z-F-R (600,0) 
M569 P9 S1                          ; Physical drive 9. Z-B-R (600,600)

;Settings_________________________________________________________
M584 X0:1 Y5 Z6:7:8:9 E3 P3                 ; Driver mapping
M671 X-185:-185:668:668 Y668:-46:-46:668 S30          ; Leadscrew mapping 

;___________________________________________________________________
M350 X16 Y16 Z16 E16 I1                   	; Configure microstepping with interpolation
M92 X80 Y80 Z2000 E415                    	; Set steps per mm
M566 X360 Y360 Z30 E3000 P1                 ; Set maximum instantaneous speed changes (mm/min)
M203 X12000 Y12000 Z400 E6000               ; Set maximum speeds (mm/min)
M201 X2000 Y2000 Z200 E3000                 ; Set accelerations (mm/s^2)
M204 P1000 T1500                      		; Set print and travel accelerations  (mm/s^2)
M906 X1800 Y1800 E1800 Z1800 I50           	; Set motor currents (mA) and motor idle factor in per cent

M84 S100                          ; Set idle timeout - 100 seconds

; Axis Limits
M208 X0 Y0 Z-2 S1                                     ; set axis minima
M208 X600 Y600 Z660 S0                                ; set axis maxima

; Endstops
M574 X1 S1 P"duex.e5stop + duex.e6stop"           ; configure switch-type (e.g. microswitch) endstop for low end on X via pin xstop
M574 Y2 S1 P"duex.e4stop"                 ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin ystop

; Z-Probe
M558 P9 C"zprobe.in" H4 F180 T8000 A1 R0.5          ; BLTouch probing settings
M950 S0 C"duex.pwm5"                    ; sets the BLTouch probe
M376 H100                                 ; Height (mm) over which to taper off the bed compensation
G31 P500 X-25.5 Y26.9                   ; BLTouch X and Y offset
M557 X{move.axes[0].min + sensors.probes[0].offsets[0] + 1, move.axes[0].max + sensors.probes[0].offsets[0] - 2} Y{move.axes[1].min + sensors.probes[0].offsets[1] + 1, move.axes[1].max + sensors.probes[0].offsets[1] - 1} P10:10
; The M557 is used to define the mesh grid area. It uses the P parameter to set the amount of probing points. P10:10 would be a 10x10 grid. Supports up to a 21x21 grid. 
M98 P"config_probe.g"                   ; Load the Z-offset from the config_probe.g file
; The Z_offset value is now set in config_probe.g, not in config.g
; Adjust the values there, do not adjust anything here.

; Automatic Z Offset Calibration____________________________________
M574 Z1 S1 P"!ystop"                    ; configure switch-type for Automatic z-offset

; Heaters___________________________________________________________
M140 H-1                                              ; disable heated bed (overrides default heater mapping)

;E0_________________________________________________________________
;M308 S0 P"e0temp" Y"thermistor" T100000 B4725 C7.06e-8         ; configure sensor 0 as thermistor on pin e0temp
;M308 S0 P"spi.cs1" Y"rtd-max31865"             ; Configure sensor 0 as PT100 via the daughterboard
M308 S0 P"e0temp" Y"pt1000"                 ; Configure sensor 0 as PT1000 on pin e0temp
M950 H0 C"e0heat" T0                                  ; create nozzle heater output on e0heat and map it to sensor 0
M98 P"PID_tune_E0.g" R1                   ; PID calibration
; M307 is not used in this config. The M307 files are stored and executed from the PID_tune_E0.g file. You can verify the values there.
M143 H0 S285                                          ; set temperature limit for heater 0 to 285C

; Fans______________________________________________________________
M950 F0 C"fan0" Q500                                  ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 C"Primary blower fan"            ; set fan 0 value. Thermostatic control is turned on
M950 F2 C"duex.fan7" Q500                               ; create LED on pin fan2 and set its frequency
M106 P2 S0 H-1 C"LED"                                   ; Disable fan channel for LED
M106 P2 S255                        ; LED on by default
M950 F3 C"duex.fan5" Q500                             ; create fan 3 on pin fan1 and set its frequency
M106 P3 S255 H0 T45                                   ; set fan 3 value. Thermostatic control is turned on

; Tools______________________________________________________________
;T0_________________________________________________________________
M563 P0 S"E0 Primary" D0 H0 F0                        ; define tool 0
G10 P0 X0 Y0 Z0                                       ; set tool 0 axis offsets
G10 P0 R0 S210                                        ; set initial tool 0 active and standby temperatures to 0C

; Automatic power saving____________________________________________
M911 S22.5 R29.0 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000"      ; Set voltage thresholds and actions to run on power loss. Power Failure Pause

; Filament sensor settings__________________________________________________
; Primary hotend Clog detector__________________________________________________
M591 D0 P7 C"e0stop" S1 L3.2 E10 R10:300          ; Clog Detector E0 [Add-On]

; Crash detector__________________________________________________
M950 J2 C"zstop"                      ; create Input Pin 2 on pin E4 to for M581 Command.
;M581 P2 T0 S0 R0                     ; Crash Detector   [Add-On]

; Emergency stop button__________________________________________________
M950 J3 C"duex.e2stop"                    ; create Input Pin 2 on pin E4 to for M581 Command.
M581 P3 T0 S1 R0                      ; Emergency stop [Add-On]
;M581 P3 T1 S1 R1                     ; Emergency stop, pause the print [Add-On]
;M581 P3 T1 S1 R0                       ; Emergency stop, pause always [Add-On]