new_modelwarper.xml

<?xml version="1.0" encoding="utf-8" ?>
<OpenSimDocument Version="40000">
	<ModelWarperConfiguration>

		<!-- `OffsetFrameWarpingStrategy`s used to warp specific frames in the model. A `StrategyTarget`
		     of `*` can be used as a lowest-priority wildcard to specify which strategy the warping engine
		     should use when it cannot find a more specific one for a given `OpenSim::PhysicalOffsetFrame`
		     in the model -->
		<OffsetFrameWarpingStrategies>

			<!-- The `ThinPlateSplineOnlyTranslationOffsetFrameWarpingStrategy` uses the thin-plate
			     spline algorithm to only warp the the `translation` part of the `OpenSim::OffsetFrame`,
			     leaving the `orientation` un-warped -->
			<ThinPlateSplineOnlyTranslationOffsetFrameWarpingStrategy>
				<StrategyTargets>
					<StrategyTarget>some_offset_frame</StrategyTarget>
					<StrategyTarget>some_other_offset_frame</StrategyTarget>
					<StrategyTarget>/bodyset/specific_path_to/another_offset_frame</StrategyTarget>
				</StrategyTargets>

				<!-- If `MeshSources` isn't specified then the warping engine will try its best to figure out
				     if there exists a common set of meshes that all of the `StrategyTarget`s are attached to,
				     followed by using that set as a warp source -->
				<PointSources>
					<LandmarkedMeshPointSource>pelvis.vtp</LandmarkedMeshPointSource>
				</PointSources>
			</ThinPlateSplineOnlyTranslationOffsetFrameWarpingStrategy>

			<!-- The `ProduceErrorOffsetFrameWarpingStrategy` will make the engine produce an error
			     if executed (i.e. if any frame has this strategy applied to it) -->
			<ProduceErrorOffsetFrameWarpingStrategy>
				<StrategyTargets>
					<StrategyTarget>*</StrategyTarget> <!-- catch-all -->
				</StrategyTargets>
			</ProduceErrorOffsetFrameWarpingStrategy>

			<!-- The `LeastSquaresOffsetFrameWarpingStrategy` is used to approximate the `translation`
			     and `orientation` properties of the target `OpenSim::OffsetFrame`by least-squares
			     fitting `OpenSim::Point`s in the model -->
			<LeastSquaresOffsetFrameWarpingStrategy>
				<StrategyTargets>
					<StrategyTarget>some_annoying_offset_frame</StrategyTarget>
				</StrategyTargets>
				<PointsToFit>
					<PointToFit>p1</PointToFit>
					<PointToFit>p2</PointToFit>
					<PointToFit>p3</PointToFit>
				</PointsToFit>
			</LeastSquaresOffsetFrameWarpingStrategy>

		</OffsetFrameWarpingStrategies>

		<!-- Lists all strategies used to warp stations (incl. muscle points) in the model -->
		<StationWarpingStrategies>

			<ThinPlateSplineStationWarpingStrategy>
				<StrategyTargets>
					<StrategyTarget>p4</StrategyTarget>
					<StrategyTarget>p5</StrategyTarget>
				</StrategyTargets>
				<!-- If this isn't specified then the engine will try to figure it out -->
				<MeshSources>
					<MeshSource>pelvis.vtp</MeshSource>
				</MeshSources>
			</ThinPlateSplineStationWarpingStrategy>

			<!-- This is what the warping engine installs, if not specified -->
			<ThinPlateSplineStationWarpingStrategy>
				<StrategyTargets>
					<StrategyTarget>*</StrategyTarget>
				</StrategyTargets>
			</ThinPlateSplineStationWarpingStrategy>

		</StationWarpingStrategies>

		<!-- Lists all strategies used to warp muscle parameters in the model -->
		<MuscleParameterWarpingStrategies>
			<ModeneseMuscleParameterWarpingStrategy>
				<StrategyTargets>
					<StrategyTarget>some_muscle</StrategyTarget>
				</StrategyTargets>
				<some_scaling_param>50</some_scaling_param>
			</ModeneseMuscleParameterWarpingStrategy>

			<!-- This is what the warping engine installs, if not specified in the configuration file -->
			<IdentityMuscleParameterWarpingStrategy>
				<StrategyTargets>
					<StrategyTarget>*</StrategyTarget>
				</StrategyTargets>
			</IdentityMuscleParameterWarpingStrategy>
		</MuscleParameterWarpingStrategies>
		
		<MeshWarpingStrategies>
			<ThinPlateSplineMeshWarpingStrategy>
				<StrategyTargets>
					<StrategyTarget priority="1">*</StrategyTarget>
				</StrategyTargets>
			</ThinPlateSplineMeshWarpingStrategy>
		</MeshWarpingStrategies>
	</ModelWarperConfiguration>
</OpenSimDocument>