bmuessig/eng

## eng
&&
#5  -t1 -s1"?Min. log radius of 4-axis machining" -s2"mm" -m1  -min=3.000 -max=999.999
#6  -t2 -s1"Rotational ref. axis for A-axis" -m1 -min=0.000 -max=3.000 -i0"X-axis" -i1"Y-axis" -i2"Z-axis" -i3"No rotation"

#104 -t2 -s1"?A-axis optimal path when G0 run" -m1 -min=0.000 -max=1.000 -i0"No" -i1"Yes"

#34  -t1 -s1"X-axis pulses per mm" -s2"pulse/mm" -m2 -min=50.000 -max=99999.000
#35  -t1 -s1"Y-axis pulses per mm" -s2"pulse/mm" -m2 -min=50.000 -max=99999.000
#36  -t1 -s1"Z-axis pulses per mm" -s2"pulse/mm" -m2 -min=50.000 -max=99999.000
#37 -m0
#38  -t1 -s1"A-axis pulses per unit" -s2"" -m2 -min=50.000 -max=999999.000
#39  -t2 -s1"A-axis unit" -m2 -min=0.000 -max=1.000 -i0"pulse/deg" -i1"pulse/circle"
#40 -t2 -s1"A- or B-axis selection" -m2 -min=0.000 -max=1.000 -i0"A axis" -i1"B axis"

#390 -t2 -s1"X-axis direction electric level" -s3"0:Low,1:High" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#391 -t2 -s1"Y-axis direction electric level" -s3"0:Low,1:High" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#392 -t2 -s1"Z-axis direction electric level" -s3"0:Low,1:High" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#393 -t2 -s1"A-axis direction electric level" -s3"0:Low,1:High" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High"

#418 -t2 -s1"X-axis pulse signal electric level" -s3"0:Low,1:High" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#419 -t2 -s1"Y-axis pulse signal electric level" -s3"0:Low,1:High" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#420 -t2 -s1"Z-axis pulse signal electric level" -s3"0:Low,1:High" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#421 -t2 -s1"A-axis pulse signal electric level" -s3"0:Low,1:High" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High"

#416 -t0 -s1"Delay between direction and pulse" -s2"ns" -m2 -min=0.000 -max=9999.000

#33 -t1 -s1"Motor starting speed" -s2"mm/min" -m2 -min=0.000 -max=999.000

#100 -t1 -s1"X-axis speed in manual mode" -s2"mm/min" -m3 -min=99.000 -max=99999.000
#101 -t1 -s1"Y-axis speed in manual mode" -s2"mm/min" -m3 -min=99.000 -max=99999.000
#102 -t1 -s1"Z-axis speed in manual mode" -s2"mm/min" -m3 -min=99.000 -max=99999.000
#103 -t1 -s1"A-axis speed in manual mode" -s2"deg/min" -m3 -min=99.000 -max=99999.000

#41 -t1 -s1"X-axis max. speed in man. mode" -s2"mm/min" -m3 -min=99.000 -max=99999.000
#42 -t1 -s1"Y-axis max. speed in man. mode" -s2"mm/min" -m3 -min=99.000 -max=99999.000
#43 -t1 -s1"Z-axis max. speed in man. mode" -s2"mm/min" -m3 -min=99.000 -max=99999.000
#44 -t1 -s1"A-axis max. speed in man. mode" -s2"deg/min" -m3 -min=99.000 -max=99999.000

#45 -t1 -s1"X-axis start accel. in man. mode" -s2"mm/s2" -m3 -min=9.000 -max=9999.000
#46 -t1 -s1"Y-axis start accel. in man. mode" -s2"mm/s2" -m3 -min=9.000 -max=9999.000
#47 -t1 -s1"Z-axis start accel. in man. mode" -s2"mm/s2" -m3 -min=9.000 -max=9999.000
#48 -t1 -s1"A-axis start accel. in man. mode" -s2"deg/s2" -m3 -min=9.000 -max=9999.000

#263 -t1 -s1"X-axis stop accel. in man. mode" -s2"mm/s2" -m3 -min=9.000 -max=9999.000
#264 -t1 -s1"Y-axis stop accel. in man. mode" -s2"mm/s2" -m3 -min=9.000 -max=9999.000
#265 -t1 -s1"Z-axis stop accel. in man. mode" -s2"mm/s2" -m3 -min=9.000 -max=9999.000
#266 -t1 -s1"A-axis stop accel. in man. mode" -s2"deg/s2" -m3 -min=9.000 -max=9999.000

#15 -t2 -s1"Speed selection" -s3"0:Set by G-Code,1:Use default speed" -m4 -min=0.000 -max=1.000 -i0"G-Code" -i1"Default"
#76 -t1 -s1"Default operating speed" -s2"mm/min" -m4 -min=10.000 -max=99999.000

#99 -t1 -s1"Operating acceleration" -s2"mm/s2" -m4 -min=9.000 -max=9999.000
#80 -t1 -s1"G0 speed" -s2"mm/min" -m4 -min=99.000 -max=99999.000

#77 -t1 -s1"Maximum speed" -s2"mm/min" -m4 -min=99.000 -max=99999.000

#78 -t1 -s1"Z-axis lifting protection speed" -s2"mm/min" -m4 -min=99.000 -max=99999.000
#79 -t1 -s1"Z-axis dropping protection speed" -m4 -min=99.000 -max=99999.000
#435 -t1 -s1"X-axis safe speed" -s2"mm/min" -m4 -min=99.000 -max=99999.000
#436 -t1 -s1"Y-axis safe speed" -s2"mm/min" -m4 -min=99.000 -max=99999.000

#82 -t1 -s1"Z-axis safe height" -s2"mm" -m4 -min=0.000 -max=99.000
#89 -t1 -s1"Z-axis retraction dist. when paused" -s2"mm" -m4 -min=0.000 -max=99.000

#395=1 -t2 -s1"Allow G53 coordinate system" -s3"0:Allow,1:Forbid" -m0 -min=0.000 -max=1.000 -i0"Allow" -i1"Forbid"
#16 -t2 -s1"Current coordinate system" -s3"0:G53,1:G54,2:G55,3:G56,4:G57,5:G58,6:G59,7:MACH" -m5 -min=1.000 -max=7.000 -i0"G53" -i1"G54" -i2"G55" -i3"G56" -i4"G57" -i5"G58" -i6"G59" -i7"MACH"

#219 -t2 -s1"Stop spindle when program is paused" -s3 "0:No,1:Yes" -m6 -min=0.000 -max=1.000 -i0"No" -i1"Yes"

#220 -t2 -s1"Spindle speed selection source" -s3"0:G-Code,1:Default speed" -m6 -min=0.000 -max=1.000 -i0"G-Code" -i1"Default"
#221 -t1 -s1"Default spindle speed" -s2"rpm" -m6 -min=10.000 -max=99999.000

#98 -t1 -s1"Maximum spindle speed" -s2"rpm" -m6 -min=99.000 -max=99999.000

#227 -t2 -s1"Spindle electric level" -s3"0:Low,1:High" -m6 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#422 -t2 -s1"Spindle PWM electric level" -s3"0:Low,1:High" -m6 -min=0.000 -max=1.000 -i0"Low" -i1"High"

#222 -t2 -s1"Enable spindle on/off (M3/M5) cmds." -s3"0:No,1:Yes" -m6 -min=0.000 -max=1.000 -i0"No" -i1"Yes"

#224 -t1 -s1"Spindle M3/M4/M5 command duration" -s2"s" -m6 -min=0.000 -max=9.000

#433 -t0 -s1"?PWM rising rate from 0V to 10V" -m6 -min=0.000 -max=65535.000

#108 -t2 -s1 "Enable M-Bus I/O command" -s3"0:No,1:Yes" -m7 -min=0.000 -max=1.000 -i0"No" -i1"Yes"

#109 -t0 -s1 "M-Bus I/O default status" -m7 -min=0 -max=4294967295

#228 -t2 -s1"M8/M9 act. electric level" -s3"0:Low,1:High" -m7 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#229 -t2 -s1"M10/M11 act. electric level" -s3"0:Low,1:High" -m7 -min=0.000 -max=1.000 -i0"Low" -i1"High"

#223 -t2 -s1"Enable M8/M9, M10/M11 commands" -s3"0:No,1:Yes" -m7 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
#225 -t1 -s1"Duration of M8/M9 commands" -s2"s" -m7 -min=0.000 -max=9.000
#226 -t1 -s1"Duration of M10/M11 commands" -s2"s" -m7 -min=0.000 -max=9.000

#49 -t0 -s1"Homing cycle count" -m8 -min=1.000 -max=5.000
#50 -t2 -s1"?HOME signal Effective when HOME" -m8 -min=0.000 -max=1.000 -i0"Ignore HOME" -i1"Continue HOME"

#51 -t2 -s1"Use hard limits for homing" -s3"0:No,1:Yes" -m8 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
#52 -t2 -s1"Enable X-axis homing function" -s3"0:No,1:Yes" -m8 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
#53 -t2 -s1"Enable Y-axis homing function" -s3"0:No,1:Yes" -m8 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
#54 -t2 -s1"Enable Z-axis homing function" -s3"0:No,1:Yes" -m8 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
#55 -t2 -s1"Enable A-axis homing function" -s3"0:No,1:Yes" -m8 -min=0.000 -max=1.000 -i0"No" -i1"Yes"

#60 -t2 -s1"X-axis homing electric level" -m8 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#61 -t2 -s1"Y-axis homing electric level" -m8 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#62 -t2 -s1"Z-axis homing electric level" -m8 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#63 -t2 -s1"A-axis homing electric level" -m8 -min=0.000 -max=1.000 -i0"Low" -i1"High"

#64 -t2 -s1"X-axis homing direction" -m8 -min=0.000 -max=1.000 -i0"Negative" -i1"Positive"
#65 -t2 -s1"Y-axis homing direction" -m8 -min=0.000 -max=1.000 -i0"Negative" -i1"Positive"
#66 -t2 -s1"Z-axis homing direction" -m8 -min=0.000 -max=1.000 -i0"Negative" -i1"Positive"
#67 -t2 -s1"A-axis homing direction" -m8 -min=0.000 -max=1.000 -i0"Negative" -i1"Positive"

#56 -t1 -s1"X-axis homing speed" -s2"mm/min" -m8 -min=99.000 -max=99999.000
#57 -t1 -s1"Y-axis homing speed" -s2"mm/min" -m8 -min=99.000 -max=99999.000
#58 -t1 -s1"Z-axis homing speed" -s2"mm/min" -m8 -min=99.000 -max=99999.000
#59 -t1 -s1"A-axis homing speed" -s2"deg/min" -m8 -min=99.000 -max=99999.000

#83 -t1 -s1"X-axis back distance after homing" -s2"mm" -m8 -min=0.000 -max=99.000
#84 -t1 -s1"Y-axis back distance after homing" -s2"mm" -m8 -min=0.000 -max=99.000
#85 -t1 -s1"Z-axis back distance after homing" -s2"mm" -m8 -min=0.000 -max=99.000
#86 -t1 -s1"A-axis back distance after homing" -s2"deg" -m8 -min=0.000 -max=360.000

#68 -t2 -s1"Tool setting function mode" -m9 -min=0.000 -max=2.000 -i0"Disable" -i1"Mode 1" -i2"Mode 2"

#70 -t2 -s1"Probe signal electric level" -m9 -min=0.000 -max=1.000 -i0"Low" -i1"High"

#69 -t1 -s1"Thickness of tool sensor" -s2"mm" -m9 -min=-99.000 -max=99.000
#71 -t2 -s1"Initial tool position" -m9 -min=0.000 -max=1.000 -i0"Current" -i1"Fixed"

#72 -t1 -s1"Initial probe position on X-axis" -s2"mm" -m9 -min=-9999.000 -max=9999.000
#73 -t1 -s1"Initial probe position on Y-axis" -s2"mm" -m9 -min=-9999.000 -max=9999.000
#74 -t1 -s1"Initial probe position on Z-axis" -s2"mm" -m9 -min=-9999.000 -max=9999.000
#75 -t1 -s1"Retraction distance after probing" -s2"mm" -m9 -min=0.000 -max=99.000

#400 -t2 -s1"Enable neg. X-axis hard limit" -s3"0:No,1:Yes" -m10 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
#401 -t2 -s1"Enable neg. Y-axis hard limit" -s3"0:No,1:Yes" -m10 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
#402 -t2 -s1"Enable neg. Z-axis hard limit" -s3"0:No,1:Yes" -m10 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
#403 -t2 -s1"Enable neg. A-axis hard limit" -s3"0:No,1:Yes" -m10 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
#404 -t2 -s1"Enable pos. X-axis hard limit" -s3"0:No,1:Yes" -m10 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
#405 -t2 -s1"Enable pos. Y-axis hard limit" -s3"0:No,1:Yes" -m10 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
#406 -t2 -s1"Enable pos. Z-axis hard limit" -s3"0:No,1:Yes" -m10 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
#407 -t2 -s1"Enable pos. A-axis hard limit" -s3"0:No,1:Yes" -m10 -min=0.000 -max=1.000 -i0"No" -i1"Yes"

#408 -t2 -s1"El. level of X-axis neg. hard limit" -s3"0:Low,1:High" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#409 -t2 -s1"El. level of Y-axis neg. hard limit" -s3"0:Low,1:High" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#410 -t2 -s1"El. level of Z-axis neg. hard limit" -s3"0:Low,1:High" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#411 -t2 -s1"El. level of A-axis neg. hard limit" -s3"0:Low,1:High" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High"

#412 -t2 -s1"El. level of X-axis pos. hard limit" -s3"0:Low,1:High" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#413 -t2 -s1"El. level of Y-axis pos. hard limit" -s3"0:Low,1:High" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#414 -t2 -s1"El. level of Z-axis pos. hard limit" -s3"0:Low,1:High" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#415 -t2 -s1"El. level of A-axis pos. hard limit" -s3"0:Low,1:High" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High"

#374 -t2 -s1"Enable software limits" -s3"0:No,1:Yes" -m11 -min=0.000 -max=1.000 -i0"No" -i1"Yes"

#375 -t1 -s1"Negative X-axis software limit" -s2"mm" -m11 -min=-9999.000 -max=9999.000
#376 -t1 -s1"Negative Y-axis software limit" -s2"mm" -m11 -min=-9999.000 -max=9999.000
#377 -t1 -s1"Negative Z-axis software limit" -s2"mm" -m11 -min=-9999.000 -max=9999.000
#378 -t1 -s1"Negative A-axis software limit" -s2"deg" -m11 -min=-9999.000 -max=9999.000

#379 -t1 -s1"Positive X-axis software limit" -s2"mm" -m11 -min=-9999.000 -max=9999.000
#380 -t1 -s1"Positive Y-axis software limit" -s2"mm" -m11 -min=-9999.000 -max=9999.000
#381 -t1 -s1"Positive Z-axis software limit" -s2"mm" -m11 -min=-9999.000 -max=9999.000
#382 -t1 -s1"Positive A-axis software limit" -s2"deg" -m11 -min=-9999.000 -max=9999.000

#430 -t2 -s1"MPG interface type" -s3"0-Serial port MPG,1-Standard MPG" -m12 -min=0.000 -max=1.000 -i0"Serial" -i1"Standard"
#431 -t1 -s1"MPG precision" -m12 -min=0.001 -max=0.01

#432 -t2 -s1"Standard MPG electric signal level" -s3"0:Low,1:High" -m12 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#434 -t2 -s1"MPG A/B phase signal level" -s3"0:Low,1:High" -m12 -min=0.000 -max=1.000 -i0"Low" -i1"High"

#428 -t2 -s1"Enable ESTOP signal on MPG" -s3"0:No,1:Yes" -m12 -min=0.000 -max=1.000 -i0"No" -i1"Yes"

#429 -t2 -s1"El. signal level of ESTOP on MPG" -s3"0:Low,1:High" -m12 -min=0.000 -max=1.000 -i0"Low" -i1"High"

#423 -t2 -s1"Enable ext. ESTOP signal" -s3"0:No,1:Yes" -m13 -min=0.000 -max=1.000 -i0"No" -i1"Yes"

#424 -t2 -s1"Electric signal level of ext. ESTOP signal" -s3"0:Low,1:High" -m13 -min=0.000 -max=1.000 -i0"Low" -i1"High"

#425 -t2 -s1"Enable extended start and pause" -s3"0:No,1:Yes" -m13 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
#426 -t2 -s1"Electric signal level of ext. START" -s3"0:Low,1:High" -m0 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#427 -t2 -s1"Electric signal level of ext. PAUSE" -s3"0:Low,1:High" -m0 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#446 -t2 -s1"Function of ext. key 1" -s3"0:START,1:Find middle" -m13 -min=0.000 -max=1.000 -i0"START" -i1"F.middle"
#447 -t2 -s1"Function of ext. key 2" -s3"0:PAUSE,1:ZERO" -m13 -min=0.000 -max=1.000 -i0"PAUSE" -i1"ZERO"

#437 -t2 -s1"Enable X-axis backlash" -s3"0:No,1:Yes" -m14 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
#438 -t2 -s1"Enable Y-axis backlash" -s3"0:No,1:Yes" -m14 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
#439 -t2 -s1"Enable Z-axis backlash" -s3"0:No,1:Yes" -m14 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
#440 -t2 -s1"Enable A-axis backlash" -s3"0:No,1:Yes" -m14 -min=0.000 -max=1.000 -i0"No" -i1"Yes"

#441 -t1 -s1"X-axis backlash distance" -s2"mm" -m14 -min=0.000 -max=0.999
#442 -t1 -s1"Y-axis backlash distance" -s2"mm" -m14 -min=0.000 -max=0.999
#443 -t1 -s1"Z-axis backlash distance" -s2"mm" -m14 -min=0.000 -max=0.999
#444 -t1 -s1"A-axis backlash distance" -s2"deg" -m14 -min=0.000 -max=9.999

#445 -t1 -s1"Backlash speed" -s2"mm/min" -m14 -min=99.000 -max=99999.000

#267 -t1 -s1"H00 tool offset" -s2"mm" -m0 -min=-999.999 -max=999.999
#268 -t1 -s1"H01 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#269 -t1 -s1"H02 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#270 -t1 -s1"H03 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#271 -t1 -s1"H04 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#272 -t1 -s1"H05 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#273 -t1 -s1"H06 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#274 -t1 -s1"H07 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#275 -t1 -s1"H08 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#276 -t1 -s1"H09 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#277 -t1 -s1"H10 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#278 -t1 -s1"H11 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#279 -t1 -s1"H12 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#280 -t1 -s1"H13 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#281 -t1 -s1"H14 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#282 -t1 -s1"H15 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#283 -t1 -s1"D00 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#284 -t1 -s1"D01 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#285 -t1 -s1"D02 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#286 -t1 -s1"D03 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#287 -t1 -s1"D04 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#288 -t1 -s1"D05 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#289 -t1 -s1"D06 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#290 -t1 -s1"D07 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#291 -t1 -s1"D08 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#292 -t1 -s1"D09 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#293 -t1 -s1"D10 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#294 -t1 -s1"D11 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#295 -t1 -s1"D12 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#296 -t1 -s1"D13 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#297 -t1 -s1"D14 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#298 -t1 -s1"D15 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#299 -m0

#1 -t2 -s1"Language" -s3"0:English,1:Chinese" -m16 -min=0.000 -max=1.000 -i0"English" -i1"Chinese"

#2 -t1 -s1"Display response (upd rate?) during operation" -m16 -min=400 -max=10000

#3 -t2 -s1"Tool path button function" -s3"0:Tool path,1:Try cutting" -m0 -min=0.000 -max=1.000 -i0"Tool path" -i1"Try cutting"
#218 -t2 -s1"Cycle start button mode" -m16 -min=0.000 -max=1.000 -i0"Pause start" -i1"Restart"
#499 -t1=888888.000 -s1"User access key" -m16 -min=0.000 -max=999999.000
#396 -t0=1600 -s1"Max. lines" -m16 -min=100.000 -max=3600.000
#495 -t1 -s1"Interpolation period" -s2"s" -m16 -min=0.002 -max=0.010

#497 -t1=0.000
#498 -t0=4.000

#18 -t1=200.0
#19 -t1=200.0
#20 -t1=3.0
#192 -t1=100.0
#193 -t1=100.0
#194 -t1=3.0

#250 -t2 -s1"Enable real(time?) toolpath painting" -s3"0:No,1:Yes" -m16 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
#253 -t2 -s1"Toolpath painting mode" -s3"0:Statue mode,1:Line mode" -m16 -min=0.000 -max=1.000 -i0"Statue" -i1"Line"

#88 -t2 -s1"Enable buzzer feedback" -s3"0:No,1:Yes" -m16 -min=0.000 -max=1.000 -i0"No" -i1"Yes"

#449 -s1"ZERO"
#450 -s1"GOTOZ"
#451 -s1"HOME"
#452 -s1"PROBE"
#453 -s1"AUTO"
#454 -s1"SIMULATE"
#455 -s1"CONT"
#456 -s1"STEP"
#457 -s1"MPG"
#458 -s1"RESET"
#459 -s1"READY"
#460 -s1"BUSY"
#461 -s1"FRO:"
#462 -s1"SRO:"
#463 -s1"SJR"
#464 -s1"Start Line: "
#465 -s1"2ND"
#466 -s1"Checking line "
#467 -s1"Main Page"
#468 -s1"File Page"
#469 -s1"Parameter Page"
#470 -s1"Normal Mode"
#471 -s1"X-:Goto, Y-:Zero"
#472 -s1"Z-:Home, A-:Do probe"
#473 -s1"X-:All GtoZ, X+:Goto X"
#474 -s1"Y+:Goto Y, Z+:Goto Z"
#475 -s1"A-:Probe"
#476 -s1"X+,X-:Pos. Y+,Y-:Adj."
#477 -s1"Z-:Enter, Z+:Cancel"
#478 -s1"Y-:Zero all, X+:Set X"
#479 -s1"Y+:Set Y, Z+:Set Z"
#480 -s1"Z-:Home all, X+:Home X"
#481 -s1"Y+:Home Y, Z+:Home Z"
#482 -s1 "Soft limit: "
#483 -s1 "TRCUT"
#484 -s1 "EDIT"
#485 -s1 "SBK"

#8=1.000
#9=1.000
#12=1.000
#13=1.000
#14=1.000
#195=0
#196=0

&&

## org
&&
#5  -t1 -s1"minimum log radius of 4axis machining" -s2"mm" -m1  -min=3.000 -max=999.999
#6  -t2 -s1"A axis rotate reference axis" -m1 -min=0.000 -max=3.000 -i0"X axis" -i1"Y axis" -i2"Z axis" -i3"not rotate"

#104 -t2 -s1"A axis optimal path when G0 run" -m1 -min=0.000 -max=1.000 -i0"No" -i1"Yes"

#34  -t1 -s1"X axis pulse equivalency" -s2"pulse/mm" -m2 -min=50.000 -max=99999.000
#35  -t1 -s1"Y axis pulse equivalency" -s2"pulse/mm" -m2 -min=50.000 -max=99999.000
#36  -t1 -s1"Z axis pulse equivalency" -s2"pulse/mm" -m2 -min=50.000 -max=99999.000
#37 -m0
#38  -t1 -s1"A axis pulse equivalency" -s2"" -m2 -min=50.000 -max=999999.000
#39  -t2 -s1"A axis pulse unit" -m2 -min=0.000 -max=1.000 -i0"pulse/deg" -i1"pulse/circle"
#40 -t2 -s1"AB axis Selection" -m2 -min=0.000 -max=1.000 -i0"A axis" -i1"B axis"

#390 -t2 -s1"X axis DIR signal Electric Level" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#391 -t2 -s1"Y axis DIR signal Electric Level" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#392 -t2 -s1"Z axis DIR signal Electric Level" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#393 -t2 -s1"A axis DIR signal Electric Level" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High"

#418 -t2 -s1"X axis Pulse signal Electric Level" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#419 -t2 -s1"Y axis Pulse signal Electric Level" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#420 -t2 -s1"Z axis Pulse signal Electric Level" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#421 -t2 -s1"A axis Pulse signal Electric Level" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High"

#416 -t0 -s1"Time interval between DIR & pulse" -s2"ns" -m2 -min=0.000 -max=9999.000

#33 -t1 -s1"Motor start speed" -s2"mm/min" -m2 -min=0.000 -max=999.000

#100 -t1 -s1"X axis manual control speed" -s2"mm/min" -m3 -min=99.000 -max=99999.000
#101 -t1 -s1"Y axis manual control speed" -s2"mm/min" -m3 -min=99.000 -max=99999.000
#102 -t1 -s1"Z axis manual control speed" -s2"mm/min" -m3 -min=99.000 -max=99999.000
#103 -t1 -s1"A axis manual control speed" -s2"deg/min" -m3 -min=99.000 -max=99999.000

#41 -t1 -s1"X Axis max speed in M_Ctrl mode" -s2"mm/min" -m3 -min=99.000 -max=99999.000
#42 -t1 -s1"Y Axis max speed in M_Ctrl mode" -s2"mm/min" -m3 -min=99.000 -max=99999.000
#43 -t1 -s1"Z Axis max speed in M_Ctrl mode" -s2"mm/min" -m3 -min=99.000 -max=99999.000
#44 -t1 -s1"A Axis max speed in M_Ctrl mode" -s2"deg/min" -m3 -min=99.000 -max=99999.000

#45 -t1 -s1"X axis start Acc in M_Ctrl mode" -s2"mm/s2" -m3 -min=9.000 -max=9999.000
#46 -t1 -s1"Y axis start Acc in M_Ctrl mode" -s2"mm/s2" -m3 -min=9.000 -max=9999.000
#47 -t1 -s1"Z axis start Acc in M_Ctrl mode" -s2"mm/s2" -m3 -min=9.000 -max=9999.000
#48 -t1 -s1"A axis start Acc in M_Ctrl mode" -s2"deg/s2" -m3 -min=9.000 -max=9999.000

#263 -t1 -s1"X axis stop Acc in M_Ctrl mode" -s2"mm/s2" -m3 -min=9.000 -max=9999.000
#264 -t1 -s1"Y axis stop Acc in M_Ctrl mode" -s2"mm/s2" -m3 -min=9.000 -max=9999.000
#265 -t1 -s1"Z axis stop Acc in M_Ctrl mode" -s2"mm/s2" -m3 -min=9.000 -max=9999.000
#266 -t1 -s1"A axis stop Acc in M_Ctrl mode" -s2"deg/s2" -m3 -min=9.000 -max=9999.000

#15 -t2 -s1"Speed Selection" -s3"0:set by G code,1:use default speed" -m4 -min=0.000 -max=1.000 -i0"G code" -i1"default"
#76 -t1 -s1"default operation speed" -s2"mm/min" -m4 -min=10.000 -max=99999.000

#99 -t1 -s1"operation acceleration" -s2"mm/s2" -m4 -min=9.000 -max=9999.000
#80 -t1 -s1"G0 Speed" -s2"mm/min" -m4 -min=99.000 -max=99999.000

#77 -t1 -s1"maximum speed" -s2"mm/min" -m4 -min=99.000 -max=99999.000

#78 -t1 -s1"Z axis lifting protection speed" -s2"mm/min" -m4 -min=99.000 -max=99999.000
#79 -t1 -s1"Z axis dropping protection speed" -m4 -min=99.000 -max=99999.000
#435 -t1 -s1"X axis protection speed" -s2"mm/min" -m4 -min=99.000 -max=99999.000
#436 -t1 -s1"Y axis protection speed" -s2"mm/min" -m4 -min=99.000 -max=99999.000

#82 -t1 -s1"Z axis safe height" -s2"mm" -m4 -min=0.000 -max=99.000
#89 -t1 -s1"Z axis back distance when pause" -s2"mm" -m4 -min=0.000 -max=99.000

#395=1 -t2 -s1"support of G53 coordinate sys" -s3"0:support,1:not support" -m0 -min=0.000 -max=1.000 -i0"Yes" -i1"No"
#16 -t2 -s1"current coordinate system" -s3"0:G53,1:G54,2:G55,3:G56,4:G57,5:G58,6:G59,7:MACH" -m5 -min=1.000 -max=7.000 -i0"G53" -i1"G54" -i2"G55" -i3"G56" -i4"G57" -i5"G58" -i6"G59" -i7"MACH"

#219 -t2 -s1"If Stop Spindle when pause" -m6 -min=0.000 -max=1.000 -i0"No" -i1"Yes"

#220 -t2 -s1"Spindle speed selection" -s3"0:set by G code,1:default speed of spindle" -m6 -min=0.000 -max=1.000 -i0"G code" -i1"default"
#221 -t1 -s1"default spindle speed" -s2"rpm" -m6 -min=10.000 -max=99999.000

#98 -t1 -s1"maximum spindle speed" -s2"rpm" -m6 -min=99.000 -max=99999.000

#227 -t2 -s1"Spindle switch Active level" -m6 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#422 -t2 -s1"definition of PWM Electric level" -m6 -min=0.000 -max=1.000 -i0"Low" -i1"High"

#222 -t2 -s1"Spindle commands M3/M5 response" -s3"0:not response,1:response" -m6 -min=0.000 -max=1.000 -i0"No" -i1"Yes"

#224 -t1 -s1"Spindle M3/M4/M5 response Duration" -s2"s" -m6 -min=0.000 -max=9.000

#433 -t0 -s1"PWM rising rate from 0V to 10V" -m6 -min=0.000 -max=65535.000

#108 -t2 -s1 "M Bus IO command response" -s3"0:not response,1:response" -m7 -min=0.000 -max=1.000 -i0"No" -i1"Yes"

#109 -t0 -s1 "M Bus IO default status" -m7 -min=0 -max=4294967295

#228 -t2 -s1"M8/M9 active electric level" -m7 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#229 -t2 -s1"M10/M11 active electric level" -m7 -min=0.000 -max=1.000 -i0"Low" -i1"High"

#223 -t2 -s1"response of M code(M8/M9,M10/M11)" -s3"0:not response,1:response" -m7 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
#225 -t1 -s1"delay time of M8/M9" -s2"s" -m7 -min=0.000 -max=9.000
#226 -t1 -s1"delay time of M10/M11" -s2"s" -m7 -min=0.000 -max=9.000

#49 -t0 -s1"HOME times" -m8 -min=1.000 -max=5.000
#50 -t2 -s1"HOME signal Effective when HOME" -m8 -min=0.000 -max=1.000 -i0"Ignore HOME" -i1"Continue HOME"

#51 -t2 -s1"Enable limit signal when HOME" -s3"0:Disable,1:Enable" -m8 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
#52 -t2 -s1"Enable X Home Searching function" -s3"0:not enable,1:enable" -m8 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
#53 -t2 -s1"Enable Y Home Searching function" -s3"0:not enable,1:enable" -m8 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
#54 -t2 -s1"Enable Z Home Searching function" -s3"0:not enable,1:enable" -m8 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
#55 -t2 -s1"Enable A Home Searching function" -s3"0:not enable,1:enable" -m8 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"

#60 -t2 -s1"X axis Home signal Electric Level" -m8 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#61 -t2 -s1"Y axis Home signal Electric Level" -m8 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#62 -t2 -s1"Z axis Home signal Electric Level" -m8 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#63 -t2 -s1"A axis Home signal Electric Level" -m8 -min=0.000 -max=1.000 -i0"Low" -i1"High"

#64 -t2 -s1"X axis Home direction" -m8 -min=0.000 -max=1.000 -i0"Negative" -i1"Positive"
#65 -t2 -s1"Y axis Home direction" -m8 -min=0.000 -max=1.000 -i0"Negative" -i1"Positive"
#66 -t2 -s1"Z axis Home direction" -m8 -min=0.000 -max=1.000 -i0"Negative" -i1"Positive"
#67 -t2 -s1"A axis Home direction" -m8 -min=0.000 -max=1.000 -i0"Negative" -i1"Positive"

#56 -t1 -s1"X axis Home speed" -s2"mm/min" -m8 -min=99.000 -max=99999.000
#57 -t1 -s1"Y axis Home speed" -s2"mm/min" -m8 -min=99.000 -max=99999.000
#58 -t1 -s1"Z axis Home speed" -s2"mm/min" -m8 -min=99.000 -max=99999.000
#59 -t1 -s1"A axis Home speed" -s2"deg/min" -m8 -min=99.000 -max=99999.000

#83 -t1 -s1"X axis back distance after Home" -s2"mm" -m8 -min=0.000 -max=99.000
#84 -t1 -s1"Y axis back distance after Home" -s2"mm" -m8 -min=0.000 -max=99.000
#85 -t1 -s1"Z axis back distance after Home" -s2"mm" -m8 -min=0.000 -max=99.000
#86 -t1 -s1"A axis back distance after Home" -s2"deg" -m8 -min=0.000 -max=360.000

#68 -t2 -s1"Tool Setting function mode " -m9 -min=0.000 -max=2.000 -i0"Disable" -i1"mode 1" -i2"mode 2"

#70 -t2 -s1"Probe signal electric level" -m9 -min=0.000 -max=1.000 -i0"Low" -i1"High"

#69 -t1 -s1"Thickness of tool sensor" -s2"mm" -m9 -min=-99.000 -max=99.000
#71 -t2 -s1"Initial tool's position" -m9 -min=0.000 -max=1.000 -i0"current position" -i1"fixed position"

#72 -t1 -s1"Initial probe position on X axis" -s2"mm" -m9 -min=-9999.000 -max=9999.000
#73 -t1 -s1"Initial probe position on Y axis" -s2"mm" -m9 -min=-9999.000 -max=9999.000
#74 -t1 -s1"Initial probe position on Z axis" -s2"mm" -m9 -min=-9999.000 -max=9999.000
#75 -t1 -s1"back distance after probe" -s2"mm" -m9 -min=0.000 -max=99.000

#400 -t2 -s1"Limited siganl active of X--" -s3"0:not enable,1:enable" -m10 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
#401 -t2 -s1"Limited siganl active of Y--" -s3"0:not enable,1:enable" -m10 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
#402 -t2 -s1"Limited siganl active of Z--" -s3"0:not enable,1:enable" -m10 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
#403 -t2 -s1"Limited siganl active of A--" -s3"0:not enable,1:enable" -m10 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
#404 -t2 -s1"Limited siganl active of X++" -s3"0:not enable,1:enable" -m10 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
#405 -t2 -s1"Limited siganl active of Y++" -s3"0:not enable,1:enable" -m10 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
#406 -t2 -s1"Limited siganl active of Z++" -s3"0:not enable,1:enable" -m10 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
#407 -t2 -s1"Limited siganl active of A++" -s3"0:not enable,1:enable" -m10 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"

#408 -t2 -s1"Effective electric level of X--" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#409 -t2 -s1"Effective electric level of Y--" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#410 -t2 -s1"Effective electric level of Z--" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#411 -t2 -s1"Effective electric level of A--" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High"

#412 -t2 -s1"Effective electric level of X++" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#413 -t2 -s1"Effective electric level of Y++" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#414 -t2 -s1"Effective electric level of Z++" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#415 -t2 -s1"Effective electric level of A++" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High"

#374 -t2 -s1"Enable software limit" -s3"0:not enable,1:enable" -m11 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"

#375 -t1 -s1"Soft-limited postion value of X--" -s2"mm" -m11 -min=-9999.000 -max=9999.000
#376 -t1 -s1"Soft-limited postion value of Y--" -s2"mm" -m11 -min=-9999.000 -max=9999.000
#377 -t1 -s1"Soft-limited postion value of Z--" -s2"mm" -m11 -min=-9999.000 -max=9999.000
#378 -t1 -s1"Soft-limited postion value of A--" -s2"deg" -m11 -min=-9999.000 -max=9999.000

#379 -t1 -s1"Soft-limited postion value of X++" -s2"mm" -m11 -min=-9999.000 -max=9999.000
#380 -t1 -s1"Soft-limited postion value of Y++" -s2"mm" -m11 -min=-9999.000 -max=9999.000
#381 -t1 -s1"Soft-limited postion value of Z++" -s2"mm" -m11 -min=-9999.000 -max=9999.000
#382 -t1 -s1"Soft-limited postion value of A++" -s2"deg" -m11 -min=-9999.000 -max=9999.000

#430 -t2 -s1"MPG interface type" -s3"0-serial port MPG\A3\AC1-standard MPG" -m12 -min=0.000 -max=1.000 -i0"Serial" -i1"Standard"
#431 -t1 -s1"MPG Precision"  -m12 -min=0.001 -max=0.01

#432 -t2 -s1"Standard MPG signal Electric Level" -m12 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#434 -t2 -s1"A/B phase signal level on MPG" -m12 -min=0.000 -max=1.000 -i0"Low" -i1"High"

#428 -t2 -s1"Enable the ESTOP signal on MPG" -s3"0:not enable,1:enable" -m12 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"

#429 -t2 -s1"Electric level of ESTOP on MPG" -m12 -min=0.000 -max=1.000 -i0"Low" -i1"High"

#423 -t2 -s1"Enable signal of extended ESTOP" -s3"0:not enable,1:enable" -m13 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"

#424 -t2 -s1"Electric level of ext-ESTOP signal" -m13 -min=0.000 -max=1.000 -i0"Low" -i1"High"

#425 -t2 -s1"Enable extended START&PAUSE" -s3"0:not enable,1:enable" -m13 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
#426 -t2 -s1"Electric level of extended START" -m0 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#427 -t2 -s1"Electric level of extended PAUSE" -m0 -min=0.000 -max=1.000 -i0"Low" -i1"High"
#446 -t2 -s1"Define the extended key function" -m13 -min=0.000 -max=1.000 -i0"START" -i1"Find Middle"
#447 -t2 -s1"Define the Function of Ext-key2" -m13 -min=0.000 -max=1.000 -i0"PAUSE" -i1"ZERO"

#437 -t2 -s1"enable of X axis backlash" -s3"0:not enable,1:enable" -m14 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
#438 -t2 -s1"enable of Y axis backlash" -s3"0:not enable,1:enable" -m14 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
#439 -t2 -s1"enable of Z axis backlash" -s3"0:not enable,1:enable" -m14 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
#440 -t2 -s1"enable of A axis backlash" -s3"0:not enable,1:enable" -m14 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"

#441 -t1 -s1"X axis backlash distance" -s2"mm" -m14 -min=0.000 -max=0.999
#442 -t1 -s1"Y axis backlash distance" -s2"mm" -m14 -min=0.000 -max=0.999
#443 -t1 -s1"Z axis backlash distance" -s2"mm" -m14 -min=0.000 -max=0.999
#444 -t1 -s1"A axis backlash distance" -s2"deg" -m14 -min=0.000 -max=9.999

#445 -t1 -s1"Backlash Speed" -s2"mm/min" -m14 -min=99.000 -max=99999.000

#267 -t1 -s1"H00 tool offset" -s2"mm" -m0 -min=-999.999 -max=999.999
#268 -t1 -s1"H01 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#269 -t1 -s1"H02 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#270 -t1 -s1"H03 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#271 -t1 -s1"H04 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#272 -t1 -s1"H05 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#273 -t1 -s1"H06 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#274 -t1 -s1"H07 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#275 -t1 -s1"H08 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#276 -t1 -s1"H09 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#277 -t1 -s1"H10 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#278 -t1 -s1"H11 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#279 -t1 -s1"H12 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#280 -t1 -s1"H13 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#281 -t1 -s1"H14 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#282 -t1 -s1"H15 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#283 -t1 -s1"D00 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#284 -t1 -s1"D01 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#285 -t1 -s1"D02 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#286 -t1 -s1"D03 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#287 -t1 -s1"D04 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#288 -t1 -s1"D05 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#289 -t1 -s1"D06 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#290 -t1 -s1"D07 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#291 -t1 -s1"D08 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#292 -t1 -s1"D09 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#293 -t1 -s1"D10 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#294 -t1 -s1"D11 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#295 -t1 -s1"D12 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#296 -t1 -s1"D13 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#297 -t1 -s1"D14 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#298 -t1 -s1"D15 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
#299 -m0

#1 -t2 -s1"language setting" -s3"0:eng,1:chs" -m16 -min=0.000 -max=1.000 -i0"Eng" -i1"\D6\D0\CE\C4"

#2 -t1 -s1"Display response during working" -m16 -min=400 -max=10000

#3 -t2 -s1"Function of tool path key" -m0 -min=0.000 -max=1.000 -i0"tool path" -i1"Try cutting"
#218 -t2 -s1"Cycle Start key mode selection" -m16 -min=0.000 -max=1.000 -i0"Pause start" -i1"Restart"
#499 -t1=888888.000 -s1"user access key" -m16 -min=0.000 -max=999999.000
#396 -t0=1600 -s1"Number of line" -m16 -min=100.000 -max=3600.000
#495 -t1 -s1"interpolation period" -s2"s" -m16 -min=0.002 -max=0.010

#497 -t1=0.000
#498 -t0=4.000

#18 -t1=200.0
#19 -t1=200.0
#20 -t1=3.0
#192 -t1=100.0
#193 -t1=100.0
#194 -t1=3.0

#250 -t2 -s1"real track paint enable" -m16 -min=0.000 -max=1.000 -i0"disable" -i1"enable"
#253 -t2 -s1"track paint mode" -m16 -min=0.000 -max=1.000 -i0"Statue Mode" -i1"Line Mode"

#88 -t2 -s1"enable of beep " -m16 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"

#449 -s1"ZERO"
#450 -s1"GOTOZ"
#451 -s1"HOME"
#452 -s1"PROBE"
#453 -s1"AUTO"
#454 -s1"SIMULATE"
#455 -s1"CONT"
#456 -s1"STEP"
#457 -s1"MPG"
#458 -s1"RESET"
#459 -s1"READY"
#460 -s1"BUSY"
#461 -s1"FRO:"
#462 -s1"SRO:"
#463 -s1"SJR"
#464 -s1"Start Line:"
#465 -s1"2ND"
#466 -s1"syntax check"
#467 -s1"Main Page"
#468 -s1"File Page"
#469 -s1"Param Page"
#470 -s1"Normal Mod"
#471 -s1"X-:gotoz Y-:zero Z-:home"
#472 -s1"A-:probe Start:goto break"
#473 -s1"X-:all gotoz X+:x gotoz"
#474 -s1"Y+:y gotoz Z+:z gotoz"
#475 -s1"A-:go probe"
#476 -s1"X+:left X-:right Y+:up Y-:down"
#477 -s1"Z-:enter Z+:cancel"
#478 -s1"Y-:all zero X+:x zero"
#479 -s1"Y+:y zero Z+:z zero"
#480 -s1"Z-:all home X+:x home"
#481 -s1"Y+:y home Z+:z home"
#482 -s1 "soft limit:"
#483 -s1 "TRCUT"
#484 -s1 "EDIT"
#485 -s1 "SBK"

#8=1.000
#9=1.000
#12=1.000
#13=1.000
#14=1.000
#195=0
#196=0

&&
	&&
	#5 -t1 -s1"?Min. log radius of 4-axis machining" -s2"mm" -m1 -min=3.000 -max=999.999
	#6 -t2 -s1"Rotational ref. axis for A-axis" -m1 -min=0.000 -max=3.000 -i0"X-axis" -i1"Y-axis" -i2"Z-axis" -i3"No rotation"

	#104 -t2 -s1"?A-axis optimal path when G0 run" -m1 -min=0.000 -max=1.000 -i0"No" -i1"Yes"

	#34 -t1 -s1"X-axis pulses per mm" -s2"pulse/mm" -m2 -min=50.000 -max=99999.000
	#35 -t1 -s1"Y-axis pulses per mm" -s2"pulse/mm" -m2 -min=50.000 -max=99999.000
	#36 -t1 -s1"Z-axis pulses per mm" -s2"pulse/mm" -m2 -min=50.000 -max=99999.000
	#37 -m0
	#38 -t1 -s1"A-axis pulses per unit" -s2"" -m2 -min=50.000 -max=999999.000
	#39 -t2 -s1"A-axis unit" -m2 -min=0.000 -max=1.000 -i0"pulse/deg" -i1"pulse/circle"
	#40 -t2 -s1"A- or B-axis selection" -m2 -min=0.000 -max=1.000 -i0"A axis" -i1"B axis"

	#390 -t2 -s1"X-axis direction electric level" -s3"0:Low,1:High" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#391 -t2 -s1"Y-axis direction electric level" -s3"0:Low,1:High" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#392 -t2 -s1"Z-axis direction electric level" -s3"0:Low,1:High" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#393 -t2 -s1"A-axis direction electric level" -s3"0:Low,1:High" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High"

	#418 -t2 -s1"X-axis pulse signal electric level" -s3"0:Low,1:High" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#419 -t2 -s1"Y-axis pulse signal electric level" -s3"0:Low,1:High" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#420 -t2 -s1"Z-axis pulse signal electric level" -s3"0:Low,1:High" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#421 -t2 -s1"A-axis pulse signal electric level" -s3"0:Low,1:High" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High"

	#416 -t0 -s1"Delay between direction and pulse" -s2"ns" -m2 -min=0.000 -max=9999.000

	#33 -t1 -s1"Motor starting speed" -s2"mm/min" -m2 -min=0.000 -max=999.000

	#100 -t1 -s1"X-axis speed in manual mode" -s2"mm/min" -m3 -min=99.000 -max=99999.000
	#101 -t1 -s1"Y-axis speed in manual mode" -s2"mm/min" -m3 -min=99.000 -max=99999.000
	#102 -t1 -s1"Z-axis speed in manual mode" -s2"mm/min" -m3 -min=99.000 -max=99999.000
	#103 -t1 -s1"A-axis speed in manual mode" -s2"deg/min" -m3 -min=99.000 -max=99999.000

	#41 -t1 -s1"X-axis max. speed in man. mode" -s2"mm/min" -m3 -min=99.000 -max=99999.000
	#42 -t1 -s1"Y-axis max. speed in man. mode" -s2"mm/min" -m3 -min=99.000 -max=99999.000
	#43 -t1 -s1"Z-axis max. speed in man. mode" -s2"mm/min" -m3 -min=99.000 -max=99999.000
	#44 -t1 -s1"A-axis max. speed in man. mode" -s2"deg/min" -m3 -min=99.000 -max=99999.000

	#45 -t1 -s1"X-axis start accel. in man. mode" -s2"mm/s2" -m3 -min=9.000 -max=9999.000
	#46 -t1 -s1"Y-axis start accel. in man. mode" -s2"mm/s2" -m3 -min=9.000 -max=9999.000
	#47 -t1 -s1"Z-axis start accel. in man. mode" -s2"mm/s2" -m3 -min=9.000 -max=9999.000
	#48 -t1 -s1"A-axis start accel. in man. mode" -s2"deg/s2" -m3 -min=9.000 -max=9999.000

	#263 -t1 -s1"X-axis stop accel. in man. mode" -s2"mm/s2" -m3 -min=9.000 -max=9999.000
	#264 -t1 -s1"Y-axis stop accel. in man. mode" -s2"mm/s2" -m3 -min=9.000 -max=9999.000
	#265 -t1 -s1"Z-axis stop accel. in man. mode" -s2"mm/s2" -m3 -min=9.000 -max=9999.000
	#266 -t1 -s1"A-axis stop accel. in man. mode" -s2"deg/s2" -m3 -min=9.000 -max=9999.000

	#15 -t2 -s1"Speed selection" -s3"0:Set by G-Code,1:Use default speed" -m4 -min=0.000 -max=1.000 -i0"G-Code" -i1"Default"
	#76 -t1 -s1"Default operating speed" -s2"mm/min" -m4 -min=10.000 -max=99999.000

	#99 -t1 -s1"Operating acceleration" -s2"mm/s2" -m4 -min=9.000 -max=9999.000
	#80 -t1 -s1"G0 speed" -s2"mm/min" -m4 -min=99.000 -max=99999.000

	#77 -t1 -s1"Maximum speed" -s2"mm/min" -m4 -min=99.000 -max=99999.000

	#78 -t1 -s1"Z-axis lifting protection speed" -s2"mm/min" -m4 -min=99.000 -max=99999.000
	#79 -t1 -s1"Z-axis dropping protection speed" -m4 -min=99.000 -max=99999.000
	#435 -t1 -s1"X-axis safe speed" -s2"mm/min" -m4 -min=99.000 -max=99999.000
	#436 -t1 -s1"Y-axis safe speed" -s2"mm/min" -m4 -min=99.000 -max=99999.000

	#82 -t1 -s1"Z-axis safe height" -s2"mm" -m4 -min=0.000 -max=99.000
	#89 -t1 -s1"Z-axis retraction dist. when paused" -s2"mm" -m4 -min=0.000 -max=99.000

	#395=1 -t2 -s1"Allow G53 coordinate system" -s3"0:Allow,1:Forbid" -m0 -min=0.000 -max=1.000 -i0"Allow" -i1"Forbid"
	#16 -t2 -s1"Current coordinate system" -s3"0:G53,1:G54,2:G55,3:G56,4:G57,5:G58,6:G59,7:MACH" -m5 -min=1.000 -max=7.000 -i0"G53" -i1"G54" -i2"G55" -i3"G56" -i4"G57" -i5"G58" -i6"G59" -i7"MACH"

	#219 -t2 -s1"Stop spindle when program is paused" -s3 "0:No,1:Yes" -m6 -min=0.000 -max=1.000 -i0"No" -i1"Yes"

	#220 -t2 -s1"Spindle speed selection source" -s3"0:G-Code,1:Default speed" -m6 -min=0.000 -max=1.000 -i0"G-Code" -i1"Default"
	#221 -t1 -s1"Default spindle speed" -s2"rpm" -m6 -min=10.000 -max=99999.000

	#98 -t1 -s1"Maximum spindle speed" -s2"rpm" -m6 -min=99.000 -max=99999.000

	#227 -t2 -s1"Spindle electric level" -s3"0:Low,1:High" -m6 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#422 -t2 -s1"Spindle PWM electric level" -s3"0:Low,1:High" -m6 -min=0.000 -max=1.000 -i0"Low" -i1"High"

	#222 -t2 -s1"Enable spindle on/off (M3/M5) cmds." -s3"0:No,1:Yes" -m6 -min=0.000 -max=1.000 -i0"No" -i1"Yes"

	#224 -t1 -s1"Spindle M3/M4/M5 command duration" -s2"s" -m6 -min=0.000 -max=9.000

	#433 -t0 -s1"?PWM rising rate from 0V to 10V" -m6 -min=0.000 -max=65535.000

	#108 -t2 -s1 "Enable M-Bus I/O command" -s3"0:No,1:Yes" -m7 -min=0.000 -max=1.000 -i0"No" -i1"Yes"

	#109 -t0 -s1 "M-Bus I/O default status" -m7 -min=0 -max=4294967295

	#228 -t2 -s1"M8/M9 act. electric level" -s3"0:Low,1:High" -m7 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#229 -t2 -s1"M10/M11 act. electric level" -s3"0:Low,1:High" -m7 -min=0.000 -max=1.000 -i0"Low" -i1"High"

	#223 -t2 -s1"Enable M8/M9, M10/M11 commands" -s3"0:No,1:Yes" -m7 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
	#225 -t1 -s1"Duration of M8/M9 commands" -s2"s" -m7 -min=0.000 -max=9.000
	#226 -t1 -s1"Duration of M10/M11 commands" -s2"s" -m7 -min=0.000 -max=9.000

	#49 -t0 -s1"Homing cycle count" -m8 -min=1.000 -max=5.000
	#50 -t2 -s1"?HOME signal Effective when HOME" -m8 -min=0.000 -max=1.000 -i0"Ignore HOME" -i1"Continue HOME"

	#51 -t2 -s1"Use hard limits for homing" -s3"0:No,1:Yes" -m8 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
	#52 -t2 -s1"Enable X-axis homing function" -s3"0:No,1:Yes" -m8 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
	#53 -t2 -s1"Enable Y-axis homing function" -s3"0:No,1:Yes" -m8 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
	#54 -t2 -s1"Enable Z-axis homing function" -s3"0:No,1:Yes" -m8 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
	#55 -t2 -s1"Enable A-axis homing function" -s3"0:No,1:Yes" -m8 -min=0.000 -max=1.000 -i0"No" -i1"Yes"

	#60 -t2 -s1"X-axis homing electric level" -m8 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#61 -t2 -s1"Y-axis homing electric level" -m8 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#62 -t2 -s1"Z-axis homing electric level" -m8 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#63 -t2 -s1"A-axis homing electric level" -m8 -min=0.000 -max=1.000 -i0"Low" -i1"High"

	#64 -t2 -s1"X-axis homing direction" -m8 -min=0.000 -max=1.000 -i0"Negative" -i1"Positive"
	#65 -t2 -s1"Y-axis homing direction" -m8 -min=0.000 -max=1.000 -i0"Negative" -i1"Positive"
	#66 -t2 -s1"Z-axis homing direction" -m8 -min=0.000 -max=1.000 -i0"Negative" -i1"Positive"
	#67 -t2 -s1"A-axis homing direction" -m8 -min=0.000 -max=1.000 -i0"Negative" -i1"Positive"

	#56 -t1 -s1"X-axis homing speed" -s2"mm/min" -m8 -min=99.000 -max=99999.000
	#57 -t1 -s1"Y-axis homing speed" -s2"mm/min" -m8 -min=99.000 -max=99999.000
	#58 -t1 -s1"Z-axis homing speed" -s2"mm/min" -m8 -min=99.000 -max=99999.000
	#59 -t1 -s1"A-axis homing speed" -s2"deg/min" -m8 -min=99.000 -max=99999.000

	#83 -t1 -s1"X-axis back distance after homing" -s2"mm" -m8 -min=0.000 -max=99.000
	#84 -t1 -s1"Y-axis back distance after homing" -s2"mm" -m8 -min=0.000 -max=99.000
	#85 -t1 -s1"Z-axis back distance after homing" -s2"mm" -m8 -min=0.000 -max=99.000
	#86 -t1 -s1"A-axis back distance after homing" -s2"deg" -m8 -min=0.000 -max=360.000

	#68 -t2 -s1"Tool setting function mode" -m9 -min=0.000 -max=2.000 -i0"Disable" -i1"Mode 1" -i2"Mode 2"

	#70 -t2 -s1"Probe signal electric level" -m9 -min=0.000 -max=1.000 -i0"Low" -i1"High"

	#69 -t1 -s1"Thickness of tool sensor" -s2"mm" -m9 -min=-99.000 -max=99.000
	#71 -t2 -s1"Initial tool position" -m9 -min=0.000 -max=1.000 -i0"Current" -i1"Fixed"

	#72 -t1 -s1"Initial probe position on X-axis" -s2"mm" -m9 -min=-9999.000 -max=9999.000
	#73 -t1 -s1"Initial probe position on Y-axis" -s2"mm" -m9 -min=-9999.000 -max=9999.000
	#74 -t1 -s1"Initial probe position on Z-axis" -s2"mm" -m9 -min=-9999.000 -max=9999.000
	#75 -t1 -s1"Retraction distance after probing" -s2"mm" -m9 -min=0.000 -max=99.000

	#400 -t2 -s1"Enable neg. X-axis hard limit" -s3"0:No,1:Yes" -m10 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
	#401 -t2 -s1"Enable neg. Y-axis hard limit" -s3"0:No,1:Yes" -m10 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
	#402 -t2 -s1"Enable neg. Z-axis hard limit" -s3"0:No,1:Yes" -m10 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
	#403 -t2 -s1"Enable neg. A-axis hard limit" -s3"0:No,1:Yes" -m10 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
	#404 -t2 -s1"Enable pos. X-axis hard limit" -s3"0:No,1:Yes" -m10 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
	#405 -t2 -s1"Enable pos. Y-axis hard limit" -s3"0:No,1:Yes" -m10 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
	#406 -t2 -s1"Enable pos. Z-axis hard limit" -s3"0:No,1:Yes" -m10 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
	#407 -t2 -s1"Enable pos. A-axis hard limit" -s3"0:No,1:Yes" -m10 -min=0.000 -max=1.000 -i0"No" -i1"Yes"

	#408 -t2 -s1"El. level of X-axis neg. hard limit" -s3"0:Low,1:High" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#409 -t2 -s1"El. level of Y-axis neg. hard limit" -s3"0:Low,1:High" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#410 -t2 -s1"El. level of Z-axis neg. hard limit" -s3"0:Low,1:High" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#411 -t2 -s1"El. level of A-axis neg. hard limit" -s3"0:Low,1:High" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High"

	#412 -t2 -s1"El. level of X-axis pos. hard limit" -s3"0:Low,1:High" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#413 -t2 -s1"El. level of Y-axis pos. hard limit" -s3"0:Low,1:High" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#414 -t2 -s1"El. level of Z-axis pos. hard limit" -s3"0:Low,1:High" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#415 -t2 -s1"El. level of A-axis pos. hard limit" -s3"0:Low,1:High" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High"

	#374 -t2 -s1"Enable software limits" -s3"0:No,1:Yes" -m11 -min=0.000 -max=1.000 -i0"No" -i1"Yes"

	#375 -t1 -s1"Negative X-axis software limit" -s2"mm" -m11 -min=-9999.000 -max=9999.000
	#376 -t1 -s1"Negative Y-axis software limit" -s2"mm" -m11 -min=-9999.000 -max=9999.000
	#377 -t1 -s1"Negative Z-axis software limit" -s2"mm" -m11 -min=-9999.000 -max=9999.000
	#378 -t1 -s1"Negative A-axis software limit" -s2"deg" -m11 -min=-9999.000 -max=9999.000

	#379 -t1 -s1"Positive X-axis software limit" -s2"mm" -m11 -min=-9999.000 -max=9999.000
	#380 -t1 -s1"Positive Y-axis software limit" -s2"mm" -m11 -min=-9999.000 -max=9999.000
	#381 -t1 -s1"Positive Z-axis software limit" -s2"mm" -m11 -min=-9999.000 -max=9999.000
	#382 -t1 -s1"Positive A-axis software limit" -s2"deg" -m11 -min=-9999.000 -max=9999.000

	#430 -t2 -s1"MPG interface type" -s3"0-Serial port MPG,1-Standard MPG" -m12 -min=0.000 -max=1.000 -i0"Serial" -i1"Standard"
	#431 -t1 -s1"MPG precision" -m12 -min=0.001 -max=0.01

	#432 -t2 -s1"Standard MPG electric signal level" -s3"0:Low,1:High" -m12 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#434 -t2 -s1"MPG A/B phase signal level" -s3"0:Low,1:High" -m12 -min=0.000 -max=1.000 -i0"Low" -i1"High"

	#428 -t2 -s1"Enable ESTOP signal on MPG" -s3"0:No,1:Yes" -m12 -min=0.000 -max=1.000 -i0"No" -i1"Yes"

	#429 -t2 -s1"El. signal level of ESTOP on MPG" -s3"0:Low,1:High" -m12 -min=0.000 -max=1.000 -i0"Low" -i1"High"

	#423 -t2 -s1"Enable ext. ESTOP signal" -s3"0:No,1:Yes" -m13 -min=0.000 -max=1.000 -i0"No" -i1"Yes"

	#424 -t2 -s1"Electric signal level of ext. ESTOP signal" -s3"0:Low,1:High" -m13 -min=0.000 -max=1.000 -i0"Low" -i1"High"

	#425 -t2 -s1"Enable extended start and pause" -s3"0:No,1:Yes" -m13 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
	#426 -t2 -s1"Electric signal level of ext. START" -s3"0:Low,1:High" -m0 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#427 -t2 -s1"Electric signal level of ext. PAUSE" -s3"0:Low,1:High" -m0 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#446 -t2 -s1"Function of ext. key 1" -s3"0:START,1:Find middle" -m13 -min=0.000 -max=1.000 -i0"START" -i1"F.middle"
	#447 -t2 -s1"Function of ext. key 2" -s3"0:PAUSE,1:ZERO" -m13 -min=0.000 -max=1.000 -i0"PAUSE" -i1"ZERO"

	#437 -t2 -s1"Enable X-axis backlash" -s3"0:No,1:Yes" -m14 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
	#438 -t2 -s1"Enable Y-axis backlash" -s3"0:No,1:Yes" -m14 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
	#439 -t2 -s1"Enable Z-axis backlash" -s3"0:No,1:Yes" -m14 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
	#440 -t2 -s1"Enable A-axis backlash" -s3"0:No,1:Yes" -m14 -min=0.000 -max=1.000 -i0"No" -i1"Yes"

	#441 -t1 -s1"X-axis backlash distance" -s2"mm" -m14 -min=0.000 -max=0.999
	#442 -t1 -s1"Y-axis backlash distance" -s2"mm" -m14 -min=0.000 -max=0.999
	#443 -t1 -s1"Z-axis backlash distance" -s2"mm" -m14 -min=0.000 -max=0.999
	#444 -t1 -s1"A-axis backlash distance" -s2"deg" -m14 -min=0.000 -max=9.999

	#445 -t1 -s1"Backlash speed" -s2"mm/min" -m14 -min=99.000 -max=99999.000

	#267 -t1 -s1"H00 tool offset" -s2"mm" -m0 -min=-999.999 -max=999.999
	#268 -t1 -s1"H01 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#269 -t1 -s1"H02 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#270 -t1 -s1"H03 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#271 -t1 -s1"H04 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#272 -t1 -s1"H05 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#273 -t1 -s1"H06 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#274 -t1 -s1"H07 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#275 -t1 -s1"H08 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#276 -t1 -s1"H09 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#277 -t1 -s1"H10 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#278 -t1 -s1"H11 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#279 -t1 -s1"H12 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#280 -t1 -s1"H13 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#281 -t1 -s1"H14 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#282 -t1 -s1"H15 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#283 -t1 -s1"D00 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#284 -t1 -s1"D01 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#285 -t1 -s1"D02 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#286 -t1 -s1"D03 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#287 -t1 -s1"D04 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#288 -t1 -s1"D05 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#289 -t1 -s1"D06 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#290 -t1 -s1"D07 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#291 -t1 -s1"D08 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#292 -t1 -s1"D09 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#293 -t1 -s1"D10 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#294 -t1 -s1"D11 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#295 -t1 -s1"D12 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#296 -t1 -s1"D13 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#297 -t1 -s1"D14 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#298 -t1 -s1"D15 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#299 -m0

	#1 -t2 -s1"Language" -s3"0:English,1:Chinese" -m16 -min=0.000 -max=1.000 -i0"English" -i1"Chinese"

	#2 -t1 -s1"Display response (upd rate?) during operation" -m16 -min=400 -max=10000

	#3 -t2 -s1"Tool path button function" -s3"0:Tool path,1:Try cutting" -m0 -min=0.000 -max=1.000 -i0"Tool path" -i1"Try cutting"
	#218 -t2 -s1"Cycle start button mode" -m16 -min=0.000 -max=1.000 -i0"Pause start" -i1"Restart"
	#499 -t1=888888.000 -s1"User access key" -m16 -min=0.000 -max=999999.000
	#396 -t0=1600 -s1"Max. lines" -m16 -min=100.000 -max=3600.000
	#495 -t1 -s1"Interpolation period" -s2"s" -m16 -min=0.002 -max=0.010

	#497 -t1=0.000
	#498 -t0=4.000

	#18 -t1=200.0
	#19 -t1=200.0
	#20 -t1=3.0
	#192 -t1=100.0
	#193 -t1=100.0
	#194 -t1=3.0

	#250 -t2 -s1"Enable real(time?) toolpath painting" -s3"0:No,1:Yes" -m16 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
	#253 -t2 -s1"Toolpath painting mode" -s3"0:Statue mode,1:Line mode" -m16 -min=0.000 -max=1.000 -i0"Statue" -i1"Line"

	#88 -t2 -s1"Enable buzzer feedback" -s3"0:No,1:Yes" -m16 -min=0.000 -max=1.000 -i0"No" -i1"Yes"

	#449 -s1"ZERO"
	#450 -s1"GOTOZ"
	#451 -s1"HOME"
	#452 -s1"PROBE"
	#453 -s1"AUTO"
	#454 -s1"SIMULATE"
	#455 -s1"CONT"
	#456 -s1"STEP"
	#457 -s1"MPG"
	#458 -s1"RESET"
	#459 -s1"READY"
	#460 -s1"BUSY"
	#461 -s1"FRO:"
	#462 -s1"SRO:"
	#463 -s1"SJR"
	#464 -s1"Start Line: "
	#465 -s1"2ND"
	#466 -s1"Checking line "
	#467 -s1"Main Page"
	#468 -s1"File Page"
	#469 -s1"Parameter Page"
	#470 -s1"Normal Mode"
	#471 -s1"X-:Goto, Y-:Zero"
	#472 -s1"Z-:Home, A-:Do probe"
	#473 -s1"X-:All GtoZ, X+:Goto X"
	#474 -s1"Y+:Goto Y, Z+:Goto Z"
	#475 -s1"A-:Probe"
	#476 -s1"X+,X-:Pos. Y+,Y-:Adj."
	#477 -s1"Z-:Enter, Z+:Cancel"
	#478 -s1"Y-:Zero all, X+:Set X"
	#479 -s1"Y+:Set Y, Z+:Set Z"
	#480 -s1"Z-:Home all, X+:Home X"
	#481 -s1"Y+:Home Y, Z+:Home Z"
	#482 -s1 "Soft limit: "
	#483 -s1 "TRCUT"
	#484 -s1 "EDIT"
	#485 -s1 "SBK"

	#8=1.000
	#9=1.000
	#12=1.000
	#13=1.000
	#14=1.000
	#195=0
	#196=0

	&&
	&&
	#5 -t1 -s1"minimum log radius of 4axis machining" -s2"mm" -m1 -min=3.000 -max=999.999
	#6 -t2 -s1"A axis rotate reference axis" -m1 -min=0.000 -max=3.000 -i0"X axis" -i1"Y axis" -i2"Z axis" -i3"not rotate"

	#104 -t2 -s1"A axis optimal path when G0 run" -m1 -min=0.000 -max=1.000 -i0"No" -i1"Yes"

	#34 -t1 -s1"X axis pulse equivalency" -s2"pulse/mm" -m2 -min=50.000 -max=99999.000
	#35 -t1 -s1"Y axis pulse equivalency" -s2"pulse/mm" -m2 -min=50.000 -max=99999.000
	#36 -t1 -s1"Z axis pulse equivalency" -s2"pulse/mm" -m2 -min=50.000 -max=99999.000
	#37 -m0
	#38 -t1 -s1"A axis pulse equivalency" -s2"" -m2 -min=50.000 -max=999999.000
	#39 -t2 -s1"A axis pulse unit" -m2 -min=0.000 -max=1.000 -i0"pulse/deg" -i1"pulse/circle"
	#40 -t2 -s1"AB axis Selection" -m2 -min=0.000 -max=1.000 -i0"A axis" -i1"B axis"

	#390 -t2 -s1"X axis DIR signal Electric Level" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#391 -t2 -s1"Y axis DIR signal Electric Level" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#392 -t2 -s1"Z axis DIR signal Electric Level" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#393 -t2 -s1"A axis DIR signal Electric Level" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High"

	#418 -t2 -s1"X axis Pulse signal Electric Level" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#419 -t2 -s1"Y axis Pulse signal Electric Level" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#420 -t2 -s1"Z axis Pulse signal Electric Level" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#421 -t2 -s1"A axis Pulse signal Electric Level" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High"

	#416 -t0 -s1"Time interval between DIR & pulse" -s2"ns" -m2 -min=0.000 -max=9999.000

	#33 -t1 -s1"Motor start speed" -s2"mm/min" -m2 -min=0.000 -max=999.000

	#100 -t1 -s1"X axis manual control speed" -s2"mm/min" -m3 -min=99.000 -max=99999.000
	#101 -t1 -s1"Y axis manual control speed" -s2"mm/min" -m3 -min=99.000 -max=99999.000
	#102 -t1 -s1"Z axis manual control speed" -s2"mm/min" -m3 -min=99.000 -max=99999.000
	#103 -t1 -s1"A axis manual control speed" -s2"deg/min" -m3 -min=99.000 -max=99999.000

	#41 -t1 -s1"X Axis max speed in M_Ctrl mode" -s2"mm/min" -m3 -min=99.000 -max=99999.000
	#42 -t1 -s1"Y Axis max speed in M_Ctrl mode" -s2"mm/min" -m3 -min=99.000 -max=99999.000
	#43 -t1 -s1"Z Axis max speed in M_Ctrl mode" -s2"mm/min" -m3 -min=99.000 -max=99999.000
	#44 -t1 -s1"A Axis max speed in M_Ctrl mode" -s2"deg/min" -m3 -min=99.000 -max=99999.000

	#45 -t1 -s1"X axis start Acc in M_Ctrl mode" -s2"mm/s2" -m3 -min=9.000 -max=9999.000
	#46 -t1 -s1"Y axis start Acc in M_Ctrl mode" -s2"mm/s2" -m3 -min=9.000 -max=9999.000
	#47 -t1 -s1"Z axis start Acc in M_Ctrl mode" -s2"mm/s2" -m3 -min=9.000 -max=9999.000
	#48 -t1 -s1"A axis start Acc in M_Ctrl mode" -s2"deg/s2" -m3 -min=9.000 -max=9999.000

	#263 -t1 -s1"X axis stop Acc in M_Ctrl mode" -s2"mm/s2" -m3 -min=9.000 -max=9999.000
	#264 -t1 -s1"Y axis stop Acc in M_Ctrl mode" -s2"mm/s2" -m3 -min=9.000 -max=9999.000
	#265 -t1 -s1"Z axis stop Acc in M_Ctrl mode" -s2"mm/s2" -m3 -min=9.000 -max=9999.000
	#266 -t1 -s1"A axis stop Acc in M_Ctrl mode" -s2"deg/s2" -m3 -min=9.000 -max=9999.000

	#15 -t2 -s1"Speed Selection" -s3"0:set by G code,1:use default speed" -m4 -min=0.000 -max=1.000 -i0"G code" -i1"default"
	#76 -t1 -s1"default operation speed" -s2"mm/min" -m4 -min=10.000 -max=99999.000

	#99 -t1 -s1"operation acceleration" -s2"mm/s2" -m4 -min=9.000 -max=9999.000
	#80 -t1 -s1"G0 Speed" -s2"mm/min" -m4 -min=99.000 -max=99999.000

	#77 -t1 -s1"maximum speed" -s2"mm/min" -m4 -min=99.000 -max=99999.000

	#78 -t1 -s1"Z axis lifting protection speed" -s2"mm/min" -m4 -min=99.000 -max=99999.000
	#79 -t1 -s1"Z axis dropping protection speed" -m4 -min=99.000 -max=99999.000
	#435 -t1 -s1"X axis protection speed" -s2"mm/min" -m4 -min=99.000 -max=99999.000
	#436 -t1 -s1"Y axis protection speed" -s2"mm/min" -m4 -min=99.000 -max=99999.000

	#82 -t1 -s1"Z axis safe height" -s2"mm" -m4 -min=0.000 -max=99.000
	#89 -t1 -s1"Z axis back distance when pause" -s2"mm" -m4 -min=0.000 -max=99.000

	#395=1 -t2 -s1"support of G53 coordinate sys" -s3"0:support,1:not support" -m0 -min=0.000 -max=1.000 -i0"Yes" -i1"No"
	#16 -t2 -s1"current coordinate system" -s3"0:G53,1:G54,2:G55,3:G56,4:G57,5:G58,6:G59,7:MACH" -m5 -min=1.000 -max=7.000 -i0"G53" -i1"G54" -i2"G55" -i3"G56" -i4"G57" -i5"G58" -i6"G59" -i7"MACH"

	#219 -t2 -s1"If Stop Spindle when pause" -m6 -min=0.000 -max=1.000 -i0"No" -i1"Yes"

	#220 -t2 -s1"Spindle speed selection" -s3"0:set by G code,1:default speed of spindle" -m6 -min=0.000 -max=1.000 -i0"G code" -i1"default"
	#221 -t1 -s1"default spindle speed" -s2"rpm" -m6 -min=10.000 -max=99999.000

	#98 -t1 -s1"maximum spindle speed" -s2"rpm" -m6 -min=99.000 -max=99999.000

	#227 -t2 -s1"Spindle switch Active level" -m6 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#422 -t2 -s1"definition of PWM Electric level" -m6 -min=0.000 -max=1.000 -i0"Low" -i1"High"

	#222 -t2 -s1"Spindle commands M3/M5 response" -s3"0:not response,1:response" -m6 -min=0.000 -max=1.000 -i0"No" -i1"Yes"

	#224 -t1 -s1"Spindle M3/M4/M5 response Duration" -s2"s" -m6 -min=0.000 -max=9.000

	#433 -t0 -s1"PWM rising rate from 0V to 10V" -m6 -min=0.000 -max=65535.000

	#108 -t2 -s1 "M Bus IO command response" -s3"0:not response,1:response" -m7 -min=0.000 -max=1.000 -i0"No" -i1"Yes"

	#109 -t0 -s1 "M Bus IO default status" -m7 -min=0 -max=4294967295

	#228 -t2 -s1"M8/M9 active electric level" -m7 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#229 -t2 -s1"M10/M11 active electric level" -m7 -min=0.000 -max=1.000 -i0"Low" -i1"High"

	#223 -t2 -s1"response of M code(M8/M9,M10/M11)" -s3"0:not response,1:response" -m7 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
	#225 -t1 -s1"delay time of M8/M9" -s2"s" -m7 -min=0.000 -max=9.000
	#226 -t1 -s1"delay time of M10/M11" -s2"s" -m7 -min=0.000 -max=9.000

	#49 -t0 -s1"HOME times" -m8 -min=1.000 -max=5.000
	#50 -t2 -s1"HOME signal Effective when HOME" -m8 -min=0.000 -max=1.000 -i0"Ignore HOME" -i1"Continue HOME"

	#51 -t2 -s1"Enable limit signal when HOME" -s3"0:Disable,1:Enable" -m8 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
	#52 -t2 -s1"Enable X Home Searching function" -s3"0:not enable,1:enable" -m8 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
	#53 -t2 -s1"Enable Y Home Searching function" -s3"0:not enable,1:enable" -m8 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
	#54 -t2 -s1"Enable Z Home Searching function" -s3"0:not enable,1:enable" -m8 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
	#55 -t2 -s1"Enable A Home Searching function" -s3"0:not enable,1:enable" -m8 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"

	#60 -t2 -s1"X axis Home signal Electric Level" -m8 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#61 -t2 -s1"Y axis Home signal Electric Level" -m8 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#62 -t2 -s1"Z axis Home signal Electric Level" -m8 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#63 -t2 -s1"A axis Home signal Electric Level" -m8 -min=0.000 -max=1.000 -i0"Low" -i1"High"

	#64 -t2 -s1"X axis Home direction" -m8 -min=0.000 -max=1.000 -i0"Negative" -i1"Positive"
	#65 -t2 -s1"Y axis Home direction" -m8 -min=0.000 -max=1.000 -i0"Negative" -i1"Positive"
	#66 -t2 -s1"Z axis Home direction" -m8 -min=0.000 -max=1.000 -i0"Negative" -i1"Positive"
	#67 -t2 -s1"A axis Home direction" -m8 -min=0.000 -max=1.000 -i0"Negative" -i1"Positive"

	#56 -t1 -s1"X axis Home speed" -s2"mm/min" -m8 -min=99.000 -max=99999.000
	#57 -t1 -s1"Y axis Home speed" -s2"mm/min" -m8 -min=99.000 -max=99999.000
	#58 -t1 -s1"Z axis Home speed" -s2"mm/min" -m8 -min=99.000 -max=99999.000
	#59 -t1 -s1"A axis Home speed" -s2"deg/min" -m8 -min=99.000 -max=99999.000

	#83 -t1 -s1"X axis back distance after Home" -s2"mm" -m8 -min=0.000 -max=99.000
	#84 -t1 -s1"Y axis back distance after Home" -s2"mm" -m8 -min=0.000 -max=99.000
	#85 -t1 -s1"Z axis back distance after Home" -s2"mm" -m8 -min=0.000 -max=99.000
	#86 -t1 -s1"A axis back distance after Home" -s2"deg" -m8 -min=0.000 -max=360.000

	#68 -t2 -s1"Tool Setting function mode " -m9 -min=0.000 -max=2.000 -i0"Disable" -i1"mode 1" -i2"mode 2"

	#70 -t2 -s1"Probe signal electric level" -m9 -min=0.000 -max=1.000 -i0"Low" -i1"High"

	#69 -t1 -s1"Thickness of tool sensor" -s2"mm" -m9 -min=-99.000 -max=99.000
	#71 -t2 -s1"Initial tool's position" -m9 -min=0.000 -max=1.000 -i0"current position" -i1"fixed position"

	#72 -t1 -s1"Initial probe position on X axis" -s2"mm" -m9 -min=-9999.000 -max=9999.000
	#73 -t1 -s1"Initial probe position on Y axis" -s2"mm" -m9 -min=-9999.000 -max=9999.000
	#74 -t1 -s1"Initial probe position on Z axis" -s2"mm" -m9 -min=-9999.000 -max=9999.000
	#75 -t1 -s1"back distance after probe" -s2"mm" -m9 -min=0.000 -max=99.000

	#400 -t2 -s1"Limited siganl active of X--" -s3"0:not enable,1:enable" -m10 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
	#401 -t2 -s1"Limited siganl active of Y--" -s3"0:not enable,1:enable" -m10 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
	#402 -t2 -s1"Limited siganl active of Z--" -s3"0:not enable,1:enable" -m10 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
	#403 -t2 -s1"Limited siganl active of A--" -s3"0:not enable,1:enable" -m10 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
	#404 -t2 -s1"Limited siganl active of X++" -s3"0:not enable,1:enable" -m10 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
	#405 -t2 -s1"Limited siganl active of Y++" -s3"0:not enable,1:enable" -m10 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
	#406 -t2 -s1"Limited siganl active of Z++" -s3"0:not enable,1:enable" -m10 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
	#407 -t2 -s1"Limited siganl active of A++" -s3"0:not enable,1:enable" -m10 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"

	#408 -t2 -s1"Effective electric level of X--" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#409 -t2 -s1"Effective electric level of Y--" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#410 -t2 -s1"Effective electric level of Z--" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#411 -t2 -s1"Effective electric level of A--" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High"

	#412 -t2 -s1"Effective electric level of X++" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#413 -t2 -s1"Effective electric level of Y++" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#414 -t2 -s1"Effective electric level of Z++" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#415 -t2 -s1"Effective electric level of A++" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High"

	#374 -t2 -s1"Enable software limit" -s3"0:not enable,1:enable" -m11 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"

	#375 -t1 -s1"Soft-limited postion value of X--" -s2"mm" -m11 -min=-9999.000 -max=9999.000
	#376 -t1 -s1"Soft-limited postion value of Y--" -s2"mm" -m11 -min=-9999.000 -max=9999.000
	#377 -t1 -s1"Soft-limited postion value of Z--" -s2"mm" -m11 -min=-9999.000 -max=9999.000
	#378 -t1 -s1"Soft-limited postion value of A--" -s2"deg" -m11 -min=-9999.000 -max=9999.000

	#379 -t1 -s1"Soft-limited postion value of X++" -s2"mm" -m11 -min=-9999.000 -max=9999.000
	#380 -t1 -s1"Soft-limited postion value of Y++" -s2"mm" -m11 -min=-9999.000 -max=9999.000
	#381 -t1 -s1"Soft-limited postion value of Z++" -s2"mm" -m11 -min=-9999.000 -max=9999.000
	#382 -t1 -s1"Soft-limited postion value of A++" -s2"deg" -m11 -min=-9999.000 -max=9999.000

	#430 -t2 -s1"MPG interface type" -s3"0-serial port MPG\A3\AC1-standard MPG" -m12 -min=0.000 -max=1.000 -i0"Serial" -i1"Standard"
	#431 -t1 -s1"MPG Precision" -m12 -min=0.001 -max=0.01

	#432 -t2 -s1"Standard MPG signal Electric Level" -m12 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#434 -t2 -s1"A/B phase signal level on MPG" -m12 -min=0.000 -max=1.000 -i0"Low" -i1"High"

	#428 -t2 -s1"Enable the ESTOP signal on MPG" -s3"0:not enable,1:enable" -m12 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"

	#429 -t2 -s1"Electric level of ESTOP on MPG" -m12 -min=0.000 -max=1.000 -i0"Low" -i1"High"

	#423 -t2 -s1"Enable signal of extended ESTOP" -s3"0:not enable,1:enable" -m13 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"

	#424 -t2 -s1"Electric level of ext-ESTOP signal" -m13 -min=0.000 -max=1.000 -i0"Low" -i1"High"

	#425 -t2 -s1"Enable extended START&PAUSE" -s3"0:not enable,1:enable" -m13 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
	#426 -t2 -s1"Electric level of extended START" -m0 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#427 -t2 -s1"Electric level of extended PAUSE" -m0 -min=0.000 -max=1.000 -i0"Low" -i1"High"
	#446 -t2 -s1"Define the extended key function" -m13 -min=0.000 -max=1.000 -i0"START" -i1"Find Middle"
	#447 -t2 -s1"Define the Function of Ext-key2" -m13 -min=0.000 -max=1.000 -i0"PAUSE" -i1"ZERO"

	#437 -t2 -s1"enable of X axis backlash" -s3"0:not enable,1:enable" -m14 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
	#438 -t2 -s1"enable of Y axis backlash" -s3"0:not enable,1:enable" -m14 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
	#439 -t2 -s1"enable of Z axis backlash" -s3"0:not enable,1:enable" -m14 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
	#440 -t2 -s1"enable of A axis backlash" -s3"0:not enable,1:enable" -m14 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"

	#441 -t1 -s1"X axis backlash distance" -s2"mm" -m14 -min=0.000 -max=0.999
	#442 -t1 -s1"Y axis backlash distance" -s2"mm" -m14 -min=0.000 -max=0.999
	#443 -t1 -s1"Z axis backlash distance" -s2"mm" -m14 -min=0.000 -max=0.999
	#444 -t1 -s1"A axis backlash distance" -s2"deg" -m14 -min=0.000 -max=9.999

	#445 -t1 -s1"Backlash Speed" -s2"mm/min" -m14 -min=99.000 -max=99999.000

	#267 -t1 -s1"H00 tool offset" -s2"mm" -m0 -min=-999.999 -max=999.999
	#268 -t1 -s1"H01 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#269 -t1 -s1"H02 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#270 -t1 -s1"H03 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#271 -t1 -s1"H04 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#272 -t1 -s1"H05 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#273 -t1 -s1"H06 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#274 -t1 -s1"H07 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#275 -t1 -s1"H08 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#276 -t1 -s1"H09 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#277 -t1 -s1"H10 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#278 -t1 -s1"H11 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#279 -t1 -s1"H12 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#280 -t1 -s1"H13 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#281 -t1 -s1"H14 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#282 -t1 -s1"H15 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#283 -t1 -s1"D00 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#284 -t1 -s1"D01 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#285 -t1 -s1"D02 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#286 -t1 -s1"D03 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#287 -t1 -s1"D04 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#288 -t1 -s1"D05 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#289 -t1 -s1"D06 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#290 -t1 -s1"D07 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#291 -t1 -s1"D08 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#292 -t1 -s1"D09 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#293 -t1 -s1"D10 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#294 -t1 -s1"D11 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#295 -t1 -s1"D12 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#296 -t1 -s1"D13 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#297 -t1 -s1"D14 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#298 -t1 -s1"D15 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999
	#299 -m0

	#1 -t2 -s1"language setting" -s3"0:eng,1:chs" -m16 -min=0.000 -max=1.000 -i0"Eng" -i1"\D6\D0\CE\C4"

	#2 -t1 -s1"Display response during working" -m16 -min=400 -max=10000

	#3 -t2 -s1"Function of tool path key" -m0 -min=0.000 -max=1.000 -i0"tool path" -i1"Try cutting"
	#218 -t2 -s1"Cycle Start key mode selection" -m16 -min=0.000 -max=1.000 -i0"Pause start" -i1"Restart"
	#499 -t1=888888.000 -s1"user access key" -m16 -min=0.000 -max=999999.000
	#396 -t0=1600 -s1"Number of line" -m16 -min=100.000 -max=3600.000
	#495 -t1 -s1"interpolation period" -s2"s" -m16 -min=0.002 -max=0.010

	#497 -t1=0.000
	#498 -t0=4.000

	#18 -t1=200.0
	#19 -t1=200.0
	#20 -t1=3.0
	#192 -t1=100.0
	#193 -t1=100.0
	#194 -t1=3.0

	#250 -t2 -s1"real track paint enable" -m16 -min=0.000 -max=1.000 -i0"disable" -i1"enable"
	#253 -t2 -s1"track paint mode" -m16 -min=0.000 -max=1.000 -i0"Statue Mode" -i1"Line Mode"

	#88 -t2 -s1"enable of beep " -m16 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"

	#449 -s1"ZERO"
	#450 -s1"GOTOZ"
	#451 -s1"HOME"
	#452 -s1"PROBE"
	#453 -s1"AUTO"
	#454 -s1"SIMULATE"
	#455 -s1"CONT"
	#456 -s1"STEP"
	#457 -s1"MPG"
	#458 -s1"RESET"
	#459 -s1"READY"
	#460 -s1"BUSY"
	#461 -s1"FRO:"
	#462 -s1"SRO:"
	#463 -s1"SJR"
	#464 -s1"Start Line:"
	#465 -s1"2ND"
	#466 -s1"syntax check"
	#467 -s1"Main Page"
	#468 -s1"File Page"
	#469 -s1"Param Page"
	#470 -s1"Normal Mod"
	#471 -s1"X-:gotoz Y-:zero Z-:home"
	#472 -s1"A-:probe Start:goto break"
	#473 -s1"X-:all gotoz X+:x gotoz"
	#474 -s1"Y+:y gotoz Z+:z gotoz"
	#475 -s1"A-:go probe"
	#476 -s1"X+:left X-:right Y+:up Y-:down"
	#477 -s1"Z-:enter Z+:cancel"
	#478 -s1"Y-:all zero X+:x zero"
	#479 -s1"Y+:y zero Z+:z zero"
	#480 -s1"Z-:all home X+:x home"
	#481 -s1"Y+:y home Z+:z home"
	#482 -s1 "soft limit:"
	#483 -s1 "TRCUT"
	#484 -s1 "EDIT"
	#485 -s1 "SBK"

	#8=1.000
	#9=1.000
	#12=1.000
	#13=1.000
	#14=1.000
	#195=0
	#196=0

	&&