Created
December 19, 2011 15:31
-
-
Save bradfa/1497690 to your computer and use it in GitHub Desktop.
BeagleBone Debian Squeeze boot with 3.1-arago kernel
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| U-Boot 2011.09-00012-ge0ff075-dirty (Dec 14 2011 - 09:51:05) | |
| I2C: ready | |
| DRAM: 256 MiB | |
| WARNING: Caches not enabled | |
| No daughter card present | |
| NAND: HW ECC Hamming Code selected | |
| nand_get_flash_type: unknown NAND device: Manufacturer ID: 0x11, Chip ID: | |
| 0x11 | |
| No NAND device found!!! | |
| 0 MiB | |
| MMC: OMAP SD/MMC: 0 | |
| *** Warning - readenv() failed, using default environment | |
| Net: cpsw | |
| Hit any key to stop autoboot: 0 | |
| SD/MMC found on device 0 | |
| reading uEnv.txt | |
| 17 bytes read | |
| Loaded environment from uEnv.txt | |
| Importing environment from mmc ... | |
| reading uImage | |
| 2912912 bytes read | |
| ## Booting kernel from Legacy Image at 80007fc0 ... | |
| Image Name: Linux-3.1.0-00008-g94082f3 | |
| Image Type: ARM Linux Kernel Image (uncompressed) | |
| Data Size: 2912848 Bytes = 2.8 MiB | |
| Load Address: 80008000 | |
| Entry Point: 80008000 | |
| Verifying Checksum ... OK | |
| XIP Kernel Image ... OK | |
| OK | |
| Starting kernel ... | |
| Uncompressing Linux... done, booting the kernel. | |
| [ 0.000000] Linux version 3.1.0-00008-g94082f3 (andrew@bradford) (gcc v | |
| ersion 4.4.5 (Debian 4.4.5-8) ) #5 Mon Dec 19 10:18:21 EST 2011 | |
| [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5 | |
| 3c7f | |
| [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction | |
| cache | |
| [ 0.000000] Machine: am335xevm | |
| [ 0.000000] Memory policy: ECC disabled, Data cache writeback | |
| [ 0.000000] AM335X ES1.0 (neon ) | |
| [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Tot | |
| al pages: 65024 | |
| [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/mmcbl | |
| k0p2 rw rootfstype=ext3 rootwait ip=none | |
| [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) | |
| [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 by | |
| tes) | |
| [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 byte | |
| s) | |
| [ 0.000000] Memory: 256MB = 256MB total | |
| [ 0.000000] Memory: 253788k/253788k available, 8356k reserved, 0K highm | |
| em | |
| [ 0.000000] Virtual kernel memory layout: | |
| [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) | |
| [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) | |
| [ 0.000000] DMA : 0xffa00000 - 0xffe00000 ( 4 MB) | |
| [ 0.000000] vmalloc : 0xd0800000 - 0xf8000000 ( 632 MB) | |
| [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) | |
| [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) | |
| [ 0.000000] .text : 0xc0008000 - 0xc0524000 (5232 kB) | |
| [ 0.000000] .init : 0xc0524000 - 0xc055d000 ( 228 kB) | |
| [ 0.000000] .data : 0xc055e000 - 0xc05b3240 ( 341 kB) | |
| [ 0.000000] .bss : 0xc05b3264 - 0xc05ed860 ( 234 kB) | |
| [ 0.000000] NR_IRQS:396 | |
| [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 in | |
| terrupts | |
| [ 0.000000] Total of 128 interrupts on 1 active controller | |
| [ 0.000000] OMAP clockevent source: GPTIMER1 at 24000000 Hz | |
| [ 0.000000] OMAP clocksource: GPTIMER2 at 24000000 Hz | |
| [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every | |
| 178956ms | |
| [ 0.000000] Console: colour dummy device 80x30 | |
| [ 0.000242] Calibrating delay loop... 498.89 BogoMIPS (lpj=2494464) | |
| [ 0.118691] pid_max: default: 32768 minimum: 301 | |
| [ 0.118844] Security Framework initialized | |
| [ 0.118963] Mount-cache hash table entries: 512 | |
| [ 0.119417] CPU: Testing write buffer coherency: ok | |
| [ 0.120538] devtmpfs: initialized | |
| [ 0.125368] print_constraints: dummy: | |
| [ 0.125820] NET: Registered protocol family 16 | |
| [ 0.126237] GPMC revision 6.0 | |
| [ 0.129120] OMAP GPIO hardware version 0.1 | |
| [ 0.131930] omap_l3_smx omap_l3_smx.0: couldn't find resource | |
| [ 0.132589] omap_mux_init: Add partition: #1: core, flags: 0 | |
| [ 0.136507] omap_i2c.1: alias fck already exists | |
| [ 0.138524] omap2_mcspi.1: alias fck already exists | |
| [ 0.139263] omap2_mcspi.2: alias fck already exists | |
| [ 0.170448] bio: create slab <bio-0> at 0 | |
| [ 0.172704] SCSI subsystem initialized | |
| [ 0.174830] usbcore: registered new interface driver usbfs | |
| [ 0.175264] usbcore: registered new interface driver hub | |
| [ 0.175570] usbcore: registered new device driver usb | |
| [ 0.175989] registerd cppi-dma Intr @ IRQ 17 | |
| [ 0.176010] Cppi41 Init Done Qmgr-base(d083a000) dma-base(d0838000) | |
| [ 0.176023] Cppi41 Init Done | |
| [ 0.177961] omap_i2c omap_i2c.1: bus 1 rev4.0 at 100 kHz | |
| [ 0.181267] Advanced Linux Sound Architecture Driver Version 1.0.24. | |
| [ 0.182763] Switching to clocksource gp timer | |
| [ 0.188721] Switched to NOHz mode on CPU #0 | |
| [ 0.208457] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) | |
| [ 0.208678] musb-hdrc musb-hdrc.0: dma type: dma-cppi41 | |
| [ 0.210102] musb-hdrc musb-hdrc.0: USB OTG mode controller at d080a000 | |
| using DMA, IRQ 18 | |
| [ 0.210317] musb-hdrc musb-hdrc.1: dma type: dma-cppi41 | |
| [ 0.211610] musb-hdrc musb-hdrc.1: USB OTG mode controller at d080c800 | |
| using DMA, IRQ 19 | |
| [ 0.212105] NET: Registered protocol family 2 | |
| [ 0.212341] IP route cache hash table entries: 2048 (order: 1, 8192 byt | |
| es) | |
| [ 0.212702] TCP established hash table entries: 8192 (order: 4, 65536 b | |
| ytes) | |
| [ 0.213029] TCP bind hash table entries: 8192 (order: 3, 32768 bytes) | |
| [ 0.213165] TCP: Hash tables configured (established 8192 bind 8192) | |
| [ 0.213182] TCP reno registered | |
| [ 0.213201] UDP hash table entries: 256 (order: 0, 4096 bytes) | |
| [ 0.213234] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) | |
| [ 0.213482] NET: Registered protocol family 1 | |
| [ 0.214205] RPC: Registered named UNIX socket transport module. | |
| [ 0.214228] RPC: Registered udp transport module. | |
| [ 0.214240] RPC: Registered tcp transport module. | |
| [ 0.214253] RPC: Registered tcp NFSv4.1 backchannel transport module. | |
| [ 0.214529] NetWinder Floating Point Emulator V0.97 (double precision) | |
| [ 0.228084] VFS: Disk quotas dquot_6.5.2 | |
| [ 0.228169] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) | |
| [ 0.228874] msgmni has been set to 495 | |
| [ 0.229897] io scheduler noop registered | |
| [ 0.229917] io scheduler deadline registered | |
| [ 0.230001] io scheduler cfq registered (default) | |
| [ 0.231127] Could not set LED4 to fully on | |
| [ 0.233531] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled | |
| [ 0.235935] omap_uart.0: ttyO0 at MMIO 0x44e09000 (irq = 72) is a OMAP | |
| UART0 | |
| [ 0.726861] console [ttyO0] enabled | |
| [ 0.731263] omap_uart.1: ttyO1 at MMIO 0x48022000 (irq = 73) is a OMAP | |
| UART1 | |
| [ 0.739285] omap_uart.2: ttyO2 at MMIO 0x48024000 (irq = 74) is a OMAP | |
| UART2 | |
| [ 0.747242] omap_uart.3: ttyO3 at MMIO 0x481a6000 (irq = 44) is a OMAP | |
| UART3 | |
| [ 0.755208] omap_uart.4: ttyO4 at MMIO 0x481a8000 (irq = 45) is a OMAP | |
| UART4 | |
| [ 0.763153] omap_uart.5: ttyO5 at MMIO 0x481aa000 (irq = 46) is a OMAP | |
| UART5 | |
| [ 0.784073] brd: module loaded | |
| [ 0.794443] loop: module loaded | |
| [ 0.797971] i2c-core: driver [tsl2550] using legacy suspend method | |
| [ 0.804528] i2c-core: driver [tsl2550] using legacy resume method | |
| [ 0.811012] at24 1-0051: 32768 byte 24c256 EEPROM, writable, 64 bytes/w | |
| rite | |
| [ 0.872821] No daughter card found | |
| [ 0.876452] at24 1-0050: 32768 byte 24c256 EEPROM, writable, 64 bytes/w | |
| rite | |
| [ 0.891767] Board name: A335BONE | |
| [ 0.895181] Board version: 00A3 | |
| [ 0.898481] The board is a AM335x Beaglebone. | |
| [ 0.903518] omap_hsmmc.0: alias fck already exists | |
| [ 0.911829] mtdoops: mtd device (mtddev=name/number) must be supplied | |
| [ 0.919026] omap2-nand driver initializing | |
| [ 0.923714] OneNAND driver initializing | |
| [ 0.972840] davinci_mdio davinci_mdio.0: davinci mdio revision 1.6 | |
| [ 0.979349] davinci_mdio davinci_mdio.0: detected phy mask fffffffe | |
| [ 0.986727] davinci_mdio.0: probed | |
| [ 0.990312] davinci_mdio davinci_mdio.0: phy[0]: device 0:00, driver SM | |
| SC LAN8710/LAN8720 | |
| [ 0.999162] CAN device driver interface | |
| [ 1.003232] CAN bus driver for Bosch D_CAN controller 1.0 | |
| [ 1.009828] usbcore: registered new interface driver cdc_ether | |
| [ 1.016247] usbcore: registered new interface driver cdc_subset | |
| [ 1.022526] Initializing USB Mass Storage driver... | |
| [ 1.027934] usbcore: registered new interface driver usb-storage | |
| [ 1.034278] USB Mass Storage support registered. | |
| [ 1.039196] musb-hdrc musb-hdrc.1: MUSB HDRC host driver | |
| [ 1.044929] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus | |
| number 1 | |
| [ 1.052882] usb usb1: New USB device found, idVendor=1d6b, idProduct=00 | |
| 02 | |
| [ 1.060026] usb usb1: New USB device strings: Mfr=3, Product=2, SerialN | |
| umber=1 | |
| [ 1.067640] usb usb1: Product: MUSB HDRC host driver | |
| [ 1.072873] usb usb1: Manufacturer: Linux 3.1.0-00008-g94082f3 musb-hcd | |
| [ 1.079827] usb usb1: SerialNumber: musb-hdrc.1 | |
| [ 1.085923] hub 1-0:1.0: USB hub found | |
| [ 1.089896] hub 1-0:1.0: 1 port detected | |
| [ 1.095670] mousedev: PS/2 mouse device common for all mice | |
| [ 1.103205] omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0 | |
| [ 1.110139] i2c /dev entries driver | |
| [ 1.116973] OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec | |
| [ 1.124018] cpuidle: using governor ladder | |
| [ 1.128981] cpuidle: using governor menu | |
| [ 1.137844] usbcore: registered new interface driver usbhid | |
| [ 1.143783] usbhid: USB HID core driver | |
| [ 1.148953] usbcore: registered new interface driver snd-usb-audio | |
| [ 1.157906] ALSA device list: | |
| [ 1.161033] No soundcards found. | |
| [ 1.164663] oprofile: hardware counters not available | |
| [ 1.169971] oprofile: using timer interrupt. | |
| [ 1.174512] nf_conntrack version 0.5.0 (3965 buckets, 15860 max) | |
| [ 1.181403] ip_tables: (C) 2000-2006 Netfilter Core Team | |
| [ 1.187184] TCP cubic registered | |
| [ 1.190583] NET: Registered protocol family 17 | |
| [ 1.195303] can: controller area network core (rev 20090105 abi 8) | |
| [ 1.201915] NET: Registered protocol family 29 | |
| [ 1.206611] can: raw protocol (rev 20090105) | |
| [ 1.211101] can: broadcast manager protocol (rev 20090105 t) | |
| [ 1.217119] Registering the dns_resolver key type | |
| [ 1.222157] VFP support v0.3: implementor 41 architecture 3 part 30 var | |
| iant c rev 3 | |
| [ 1.230246] ThumbEE CPU extension supported. | |
| [ 1.235660] _regulator_get: mpu.0 supply mpu not found, using dummy reg | |
| ulator | |
| [ 1.243314] omap2_set_init_voltage: Fail set voltage-dpll_mpu_ck(f=5000 | |
| 00000 v=1100000)on vddmpu | |
| [ 1.252553] omap2_set_init_voltage: unable to set vdd_mpu | |
| [ 1.264314] Detected MACID=40:5f:c2:76:7f:94 | |
| [ 1.271799] omap_rtc omap_rtc: setting system clock to 2000-01-01 00:00 | |
| :00 UTC (946684800) | |
| [ 1.281184] Waiting for root device /dev/mmcblk0p2... | |
| [ 1.355646] mmc0: host does not support reading read-only switch. assum | |
| ing write-enable. | |
| [ 1.369236] mmc0: new high speed SDHC card at address e624 | |
| [ 1.375835] mmcblk0: mmc0:e624 SU08G 7.40 GiB | |
| [ 1.383370] mmcblk0: p1 p2 | |
| [ 1.400193] kjournald starting. Commit interval 5 seconds | |
| [ 1.414613] EXT3-fs (mmcblk0p2): using internal journal | |
| [ 1.420124] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data m | |
| ode | |
| [ 1.427436] VFS: Mounted root (ext3 filesystem) on device 179:2. | |
| [ 1.436069] devtmpfs: mounted | |
| [ 1.439655] Freeing init memory: 228K | |
| INIT: version 2.88 booting | |
| Using makefile-style concurrent boot in runlevel S. | |
| Starting the hotplug events dispatcher: udevd[ 2.066695] udev[576]: sta | |
| rting version 164 | |
| . | |
| Synthesizing the initial hotplug events...done. | |
| Waiting for /dev to be fully populated...done. | |
| Activating swap...done. | |
| Checking root file system...fsck from util-linux-ng 2.17.2 | |
| rootfs: clean, 12520/481440 files, 135559/1922048 blocks (check in 3 mount | |
| s) | |
| done. | |
| [ 5.184894] EXT3-fs (mmcblk0p2): using internal journal | |
| Cleaning up ifupdown.... | |
| Setting up networking.... | |
| Activating lvm and md swap...done. | |
| Checking file systems...fsck from util-linux-ng 2.17.2 | |
| done. | |
| Mounting local filesystems...done. | |
| Activating swapfile swap...done. | |
| Cleaning up temporary files.... | |
| Configuring network interfaces...done. | |
| Cleaning up temporary files.... | |
| INIT: Entering runlevel: 2 | |
| Using makefile-style concurrent boot in runlevel 2. | |
| Loading cpufreq kernel modules.../etc/init.d/loadcpufreq: 237: /sbin/lsmod | |
| : not found | |
| done (none). | |
| CPUFreq Utilities: Setting ondemand CPUFreq governor...disabled, governor | |
| not available...done. | |
| [ 7.204811] | |
| [ 7.204823] CPSW phy found : id is : 0x7c0f1 | |
| [ 7.211636] PHY 0:01 not found | |
| Debian GNU/Linux 6.0 bone1 ttyO0 | |
| bone1 login: [ 10.203423] PHY: 0:00 - Link is Up - 100/Full | |
| Debian GNU/Linux 6.0 bone1 ttyO0 | |
| bone1 login: root | |
| Last login: Fri Dec 31 19:01:52 EST 1999 on ttyO0 | |
| Linux bone1 3.1.0-00008-g94082f3 #5 Mon Dec 19 10:18:21 EST 2011 armv7l | |
| The programs included with the Debian GNU/Linux system are free software; | |
| the exact distribution terms for each program are described in the | |
| individual files in /usr/share/doc/*/copyright. | |
| Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent | |
| permitted by applicable law. | |
| root@bone1:~# |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment