BeagleBone boot with Debian Squeeze and Linux 3.2.11 on UART1

bootlog.txt

U-Boot SPL 2011.09-00036-ga61c346-dirty (Mar 14 2012 - 11:13:20)
Texas Instruments Revision detection unimplemented
OMAP SD/MMC: 0
reading u-boot.img
reading u-boot.img


U-Boot 2011.09-00036-ga61c346-dirty (Mar 14 2012 - 11:13:20)

I2C:   ready
DRAM:  256 MiB
WARNING: Caches not enabled
No daughter card present
NAND:  HW ECC Hamming Code selected
No NAND device found!!!
0 MiB
MMC:   OMAP SD/MMC: 0
*** Warning - readenv() failed, using default environment

Net:   cpsw
Hit any key to stop autoboot:  0 
SD/MMC found on device 0
reading uEnv.txt

329 bytes read
Loaded environment from uEnv.txt
Importing environment from mmc ...
Running uenvcmd ...
Loading file "firstboot" from mmc device 0:2 (xxa2)
** File not found firstboot
Loading file "uImage" from mmc device 0:2 (xxa2)
2216744 bytes read
## Booting kernel from Legacy Image at 80007fc0 ...
   Image Name:   Linux-3.2.11-12130-gcd1211d-dirt
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2216680 Bytes = 2.1 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   XIP Kernel Image ... OK
OK

Starting kernel ...

[    0.000000] Linux version 3.2.11-12130-gcd1211d-dirty (andrew@bradford) (gcc version 4.4.5 (Debian 4.4.5-8) ) #2 Thu Mar 15 16:10:11 EDT 2012
[    0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: am335xevm
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] AM335X ES1.0 (sgx neon )
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
[    0.000000] Kernel command line: console=ttyO1,115200n8 root=/dev/mmcblk0p3 rw rootfstype=ext4 rootwait ip=none
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 256MB = 256MB total
[    0.000000] Memory: 255260k/255260k available, 6884k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff000000   ( 744 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc03ec000   (3984 kB)
[    0.000000]       .init : 0xc03ec000 - 0xc041c000   ( 192 kB)
[    0.000000]       .data : 0xc041c000 - 0xc045c940   ( 259 kB)
[    0.000000]        .bss : 0xc045c964 - 0xc047cb94   ( 129 kB)
[    0.000000] NR_IRQS:396
[    0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts
[    0.000000] Total of 128 interrupts on 1 active controller
[    0.000000] OMAP clockevent source: GPTIMER1 at 24000000 Hz
[    0.000000] OMAP clocksource: GPTIMER2 at 24000000 Hz
[    0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[    0.000000] Console: colour dummy device 80x30
[    0.000203] Calibrating delay loop... 718.02 BogoMIPS (lpj=3590144)
[    0.059018] pid_max: default: 32768 minimum: 301
[    0.059149] Security Framework initialized
[    0.059215] Mount-cache hash table entries: 512
[    0.059609] CPU: Testing write buffer coherency: ok
[    0.060408] devtmpfs: initialized
[    0.064591] print_constraints: dummy: 
[    0.064946] NET: Registered protocol family 16
[    0.065060] GPMC revision 6.0
[    0.067250] OMAP GPIO hardware version 0.1
[    0.069828] omap_mux_init: Add partition: #1: core, flags: 0
[    0.070552] _omap_mux_get_by_name: Could not find signal uart1_cts.uart1_cts
[    0.070571] omap_hwmod_mux_init: Could not allocate device mux entry
[    0.070850] _omap_mux_get_by_name: Could not find signal uart2_cts.uart2_cts
[    0.070867] omap_hwmod_mux_init: Could not allocate device mux entry
[    0.071123] _omap_mux_get_by_name: Could not find signal uart3_cts_rctx.uart3_cts_rctx
[    0.071140] omap_hwmod_mux_init: Could not allocate device mux entry
[    0.072171]  omap_i2c.1: alias fck already exists
[    0.072758] failed to create an alias: icss_uart_gclk --> pruss
[    0.072790] failed to create an alias: gfx_fclk --> sgx_ck
[    0.073075]  omap2_mcspi.1: alias fck already exists
[    0.073279]  omap2_mcspi.2: alias fck already exists
[    0.090225] bio: create slab <bio-0> at 0
[    0.092098] SCSI subsystem initialized
[    0.093753] usbcore: registered new interface driver usbfs
[    0.094056] usbcore: registered new interface driver hub
[    0.094263] usbcore: registered new device driver usb
[    0.094973] omap_i2c omap_i2c.1: bus 1 rev2.4.0 at 100 kHz
[    0.097575] Switching to clocksource gp timer
[    0.097786] FS-Cache: Loaded
[    0.098170] CacheFiles: Loaded
[    0.116174] NET: Registered protocol family 2
[    0.116394] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.116716] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    0.116879] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[    0.116979] TCP: Hash tables configured (established 8192 bind 8192)
[    0.116993] TCP reno registered
[    0.117008] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.117038] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.117255] NET: Registered protocol family 1
[    0.117539] RPC: Registered named UNIX socket transport module.
[    0.117555] RPC: Registered udp transport module.
[    0.117566] RPC: Registered tcp transport module.
[    0.117576] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.118879] cpuidle-am33xx cpuidle-am33xx.0: failed to register driver
[    0.130618] VFS: Disk quotas dquot_6.5.2
[    0.130701] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.131904] msgmni has been set to 498
[    0.132466] io scheduler noop registered
[    0.132481] io scheduler deadline registered
[    0.132547] io scheduler cfq registered (default)
[    0.134771] ecap: probe of ecap.2 failed with error -2
[    0.135516] omap_uart.0: ttyO0 at MMIO 0x44e09000 (irq = 72) is a OMAP UART0
[    0.135980] omap_uart.1: ttyO1 at MMIO 0x48022000 (irq = 73) is a OMAP UART1
[    0.616378] console [ttyO1] enabled
[    0.620554] omap_uart.2: ttyO2 at MMIO 0x48024000 (irq = 74) is a OMAP UART2
[    0.628359] omap_uart.3: ttyO3 at MMIO 0x481a6000 (irq = 44) is a OMAP UART3
[    0.636104] omap_uart.4: ttyO4 at MMIO 0x481a8000 (irq = 45) is a OMAP UART4
[    0.643897] omap_uart.5: ttyO5 at MMIO 0x481aa000 (irq = 46) is a OMAP UART5
[    0.661497] brd: module loaded
[    0.670004] loop: module loaded
[    0.673361] at24 1-0051: 32768 byte 24c256 EEPROM, writable, 64 bytes/write
[    0.737619] No daughter card found
[    0.741210] at24 1-0050: 32768 byte 24c256 EEPROM, writable, 64 bytes/write
[    0.756394] Board name: A335BONE
[    0.759770] Board version: 00A3
[    0.763040] The board is a AM335x Beaglebone.
[    0.768433] tps65217 1-0024: TPS65217 ID 0x7 version 1.0
[    0.776083] print_constraints: DCDC1: 900 <--> 1800 mV at 1800 mV 
[    0.784697] print_constraints: DCDC2: 900 <--> 3300 mV at 1275 mV 
[    0.793252] print_constraints: DCDC3: 900 <--> 1500 mV at 1100 mV 
[    0.801825] print_constraints: LDO1: 1000 <--> 3300 mV at 1800 mV 
[    0.810392] print_constraints: LDO2: 900 <--> 3300 mV at 3300 mV 
[    0.818792] print_constraints: LDO3: 1800 <--> 3300 mV at 3300 mV 
[    0.827279] print_constraints: LDO4: 1800 <--> 3300 mV at 3300 mV 
[    0.834162]  omap_hsmmc.0: alias fck already exists
[    0.839685]  omap_i2c.3: alias fck already exists
[    0.844939] omap_i2c omap_i2c.3: bus 3 rev2.4.0 at 100 kHz
[    0.851156] _omap_mux_get_by_name: Could not find signal leds-gpio
[    0.907660] davinci_mdio davinci_mdio.0: davinci mdio revision 1.6
[    0.914113] davinci_mdio davinci_mdio.0: detected phy mask fffffffe
[    0.921372] davinci_mdio.0: probed
[    0.924923] davinci_mdio davinci_mdio.0: phy[0]: device 0:00, driver SMSC LAN8710/LAN8720
[    0.933626] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.940646] Initializing USB Mass Storage driver...
[    0.945927] usbcore: registered new interface driver usb-storage
[    0.952211] USB Mass Storage support registered.
[    0.957524] omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0
[    0.964208] omap_rtc: already running
[    0.968390] i2c /dev entries driver
[    0.973428] OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
[    0.983295] oprofile: hardware counters not available
[    0.988608] oprofile: using timer interrupt.
[    0.993088] nf_conntrack version 0.5.0 (3988 buckets, 15952 max)
[    0.999865] ip_tables: (C) 2000-2006 Netfilter Core Team
[    1.005530] TCP cubic registered
[    1.008935] NET: Registered protocol family 17
[    1.013618] Registering the dns_resolver key type
[    1.018619] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
[    1.026612] ThumbEE CPU extension supported.
[    1.031138] mux: Failed to setup hwmod io irq -22
[    1.036739] omap2_set_init_voltage: unable to get clk dpll1_ck
[    1.042850] omap2_set_init_voltage: unable to set vdd_mpu_iva
[    1.048883] omap2_set_init_voltage: unable to get clk l3_ick
[    1.054780] omap2_set_init_voltage: unable to set vdd_core
[    1.060509] Power Management for AM33XX family
[    1.066984] Detected MACID=40:5f:c2:76:95:98
[    1.072678] omap_rtc omap_rtc: setting system clock to 2012-03-21 15:41:20 UTC (1332344480)
[    1.081965] Waiting for root device /dev/mmcblk0p3...
[    1.170592] mmc0: host does not support reading read-only switch. assuming write-enable.
[    1.182663] mmc0: new high speed SDHC card at address e624
[    1.189080] mmcblk0: mmc0:e624 SU04G 3.69 GiB 
[    1.196799]  mmcblk0: p1 p2 p3
[    1.311914] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null)
[    1.320483] VFS: Mounted root (ext4 filesystem) on device 179:3.
[    1.327707] devtmpfs: mounted
[    1.331162] Freeing init memory: 192K
modprobe: FATAL: Could not load /lib/modules/3.2.11-12130-gcd1211d-dirty/modules.dep: No such file or directory

INIT: version 2.88 booting
Using makefile-style concurrent boot in runlevel S.
Starting the hotplug events dispatcher: udevd[    1.960031] udev[492]: starting version 164
.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...done.
Activating swap...done.
[    3.381132] EXT4-fs (mmcblk0p3): re-mounted. Opts: (null)
Cleaning up ifupdown....
Setting up networking....
Loading kernel modules...done.
Activating lvm and md swap...done.
Checking file systems...fsck from util-linux-ng 2.17.2
boot: clean, 12/15360 files, 2061/15360 blocks
done.
Mounting local filesystems...[    4.236018] EXT4-fs (mmcblk0p2): mounting ext3 file system using the ext4 subsystem
[    4.255885] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
done.
Activating swapfile swap...done.
Cleaning up temporary files....
Configuring network interfaces...done.
Starting portmap daemon....
Starting NFS common utilities: statd.
Cleaning up temporary files....
Setting kernel variables ...done.
[    5.119286] 
[    5.119295] CPSW phy found : id is : 0x7c0f1
[    5.126044] PHY 0:01 not found
INIT: Entering runlevel: 2
Using makefile-style concurrent boot in runlevel 2.
Starting portmap daemon...Already running..
Starting NFS common utilities: statd.
Starting enhanced syslogd: rsyslogd.
Starting web server: apache2apache2: Could not reliably determine the server's fully qualified domain name, using 127.0.0.1 for ServerName
.
Starting NTP server: ntpd.
Starting system message bus: dbus.
Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
Starting network plug daemon: netplugd.
[    8.118267] PHY: 0:00 - Link is Up - 100/Full

Debian GNU/Linux 6.0 bone1 ttyO1

bone1 login: