Booting the BeagleBoard-xM

BeagleBoard-xM Boot

Texas Instruments X-Loader 1.4.4ss (Aug 19 2010 - 02:49:27)
Beagle xM Rev A
Reading boot sector
Loading u-boot.bin from mmc


U-Boot 2010.03-dirty (Aug 20 2010 - 20:50:46)

OMAP3630/3730-GP ES2.0, CPU-OPP2, L3-165MHz,
OMAP3 Beagle board + LPDDR/NAND
I2C:   ready
DRAM:  512 MB
NAND:  0 MiB
*** Warning - bad CRC or NAND, using default environment

In:    serial
Out:   serial
Err:   serial

Probing for expansion boards, if none are connected you'll see a harmles
s I2C error.

No EEPROM on expansion board
Beagle xM Rev A
Die ID #146000011ff00000015739eb0b021002
Hit any key to stop autoboot:  0
mmc1 is available
The user button is currently NOT pressed.
reading boot.scr

** Unable to read "boot.scr" from mmc 1:1 **
reading user.scr

755 bytes read
Running bootscript from mmc ...
## Executing script at 80200000
mmc1 is available
reading ramdisk.gz

19960110 bytes read
reading uImage

3190568 bytes read
Booting from ramdisk ...
## Booting kernel from Legacy Image at 80200000 ...
   Image Name:   Angstrom/2.6.32/beagleboard
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3190504 Bytes =  3 MB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux.....................................................
........................................................................
........................................................................
........... done, booting the kernel.
[    0.000000] Linux version 2.6.32 (ubuntu@ip-10-204-115-71) (gcc versi
on 4.3.3 (GCC) ) #3 PREEMPT Wed Aug 18 15:53:03 UTC 2010
[    0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10
c53c7f
[    0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instru
ction cache
[    0.000000] Machine: OMAP3 Beagle Board
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] OMAP3630/DM3730 ES1.0 (l2cache iva sgx neon isp 192mhz_cl
k )
[    0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x10000
0
[    0.000000] Reserving 16777216 bytes SDRAM for VRAM
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  T
otal pages: 117760
[    0.000000] Kernel command line: console=tty0 console=ttyS2,115200n8
mem=80M@0x80000000 mem=384M@0x88000000 mpurate=1000 buddy=none camera=lb
cm3m1 vram=16M omapfb.vram=0:8M,1:4M,2:4M omapfb.mode=dvi:1024x768MR-16@
60 omapdss.def_disp=dvi root=/dev/ram0 rw ramdisk_size=131072 initrd=0x8
8000000,128M rootfstype=ext2
[    0.000000] Beagle expansionboard: none
[    0.000000] Beagle cameraboard: lbcm3m1
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144
bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 b
ytes)
[    0.000000] Memory: 80MB 384MB = 464MB total
[    0.000000] Memory: 316288KB available (5880K code, 671K data, 204K i
nit, 0K highmem)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:402
[    0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/600 MHz
[    0.000000] Reprogramming SDRC clock to 332000000 Hz
[    0.000000] GPMC revision 5.0
[    0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 i
nterrupts
[    0.000000] Total of 96 interrupts on 1 active controller
[    0.000000] OMAP GPIO hardware version 2.5
[    0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz
[    0.000000] Console: colour dummy device 80x30
[    0.000000] console [tty0] enabled
[    0.000000] Calibrating delay loop... 484.21 BogoMIPS (lpj=1892352)
[    0.000000] Mount-cache hash table entries: 512
[    0.000000] CPU: Testing write buffer coherency: ok
[    0.000000] tmpfs: No value for mount option 'mode'
[    0.000000] devtmpfs: initialized
[    0.000000] regulator: core version 0.5
[    0.000000] NET: Registered protocol family 16
[    0.000000] Beagle cameraboard: registering i2c2 bus for lbcm3m1
[    0.000000] Found NAND on CS0
[    0.000000] Registering NAND on CS0
[    0.000000] Unable to get DVI reset GPIO
[    0.000000] omap_init_mbox: platform not supported
[    0.000000] Target VDD1 OPP = 4, VDD2 OPP = 2
[   62.669708] OMAP DMA hardware revision 5.0
[   62.676025] bio: create slab <bio-0> at 0
[   62.677276] SCSI subsystem initialized
[   62.678680] usbcore: registered new interface driver usbfs
[   62.678833] usbcore: registered new interface driver hub
[   62.679046] usbcore: registered new device driver usb
[   62.679412] i2c_omap i2c_omap.1: bus 1 rev4.0 at 2600 kHz
[   62.682098] twl4030: PIH (irq 7) chaining IRQs 368..375
[   62.682159] twl4030: power (irq 373) chaining IRQs 376..383
[   62.682434] twl4030: gpio (irq 368) chaining IRQs 384..401
[   62.684234] regulator: VUSB1V5: 1500 mV normal standby
[   62.684478] regulator: VUSB1V8: 1800 mV normal standby
[   62.684722] regulator: VUSB3V1: 3100 mV normal standby
[   62.685974] twl4030_usb twl4030_usb: Initialized TWL4030 USB module
[   62.686401] regulator: VMMC1: 1850 <--> 3150 mV normal standby
[   62.686676] regulator: VDAC: 1800 mV normal standby
[   62.686920] regulator: VPLL2: 1800 mV normal standby
[   62.687164] regulator: VSIM: 1800 <--> 3000 mV normal standby
[   62.687530] regulator: VAUX3: 1800 mV normal standby
[   62.687896] regulator: VAUX4: 1800 mV normal standby
[   62.688110] i2c_omap i2c_omap.2: bus 2 rev4.0 at 400 kHz
[   62.696807] i2c_omap i2c_omap.3: bus 3 rev4.0 at 100 kHz
[   62.698028] Switching to clocksource 32k_counter
[   62.707000] musb_hdrc: version 6.0, musb-dma, otg (peripheral+host),
debug=0
[   62.710632] musb_hdrc: USB OTG mode controller at fa0ab000 using DMA,
 IRQ 92
[   62.710693] musb_hdrc musb_hdrc: MUSB HDRC host driver
[   62.710845] musb_hdrc musb_hdrc: new USB bus registered, assigned bus
 number 1
[   62.710998] usb usb1: New USB device found, idVendor=1d6b, idProduct=
0002
[   62.711029] usb usb1: New USB device strings: Mfr=3, Product=2, Seria
lNumber=1
[   62.711090] usb usb1: Product: MUSB HDRC host driver
[   62.711120] usb usb1: Manufacturer: Linux 2.6.32 musb-hcd
[   62.711151] usb usb1: SerialNumber: musb_hdrc
[   62.711791] hub 1-0:1.0: USB hub found
[   62.711853] hub 1-0:1.0: 1 port detected
[   62.712890] NET: Registered protocol family 2
[   62.713134] IP route cache hash table entries: 4096 (order: 2, 16384
bytes)
[   62.713714] TCP established hash table entries: 16384 (order: 5, 1310
72 bytes)
[   62.714202] TCP bind hash table entries: 16384 (order: 4, 65536 bytes
)
[   62.714447] TCP: Hash tables configured (established 16384 bind 16384
)
[   62.714477] TCP reno registered
[   62.714508] UDP hash table entries: 256 (order: 0, 4096 bytes)
[   62.714569] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[   62.714813] NET: Registered protocol family 1
[   62.715270] RPC: Registered udp transport module.
[   62.715332] RPC: Registered tcp transport module.
[   62.715362] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   62.715667] Trying to unpack rootfs image as initramfs...
[   62.718383] rootfs image is not initramfs (no cpio magic); looks like
 an initrd
[   63.286132] Freeing initrd memory: 131072K
[   63.286926] omap-iommu omap-iommu.0: isp registered
[   63.288696] VFS: Disk quotas dquot_6.5.2
[   63.288848] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes
)
[   63.289916] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[   63.290832] JFFS2 version 2.2. (NAND) (SUMMARY)  �© 2001-2006 Red Hat
, Inc.
[   63.291687] msgmni has been set to 874
[   63.295471] alg: No test for stdrng (krng)
[   63.295776] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 254)
[   63.295837] io scheduler noop registered
[   63.295867] io scheduler deadline registered
[   63.296051] io scheduler cfq registered (default)
[   63.354522] OMAP DSS rev 2.0
[   63.354583] OMAP DISPC rev 3.0
[   63.354675] OMAP VENC rev 2
[   63.354919] OMAP DSI rev 1.0
[   63.691375] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[   63.708801] serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST
16654
[   63.725555] serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST
16654
[   63.742279] serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST
16654
[   64.342254] console [ttyS2] enabled
[   64.352539] brd: module loaded
[   64.358947] loop: module loaded
[   64.363281] omap2-nand driver initializing
[   64.367675] No NAND device found!!!
[   64.371368] No NAND device found!!!
[   64.375885] usbcore: registered new interface driver catc
[   64.381408] catc: v2.8:CATC EL1210A NetMate USB Ethernet driver
[   64.387481] usbcore: registered new interface driver kaweth
[   64.393127] pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Eth
ernet driver
[   64.400787] usbcore: registered new interface driver pegasus
[   64.406555] rtl8150: v0.6.2 (2004/08/27):rtl8150 based usb-ethernet d
river
[   64.413574] usbcore: registered new interface driver rtl8150
[   64.419403] usbcore: registered new interface driver asix
[   64.424957] usbcore: registered new interface driver cdc_ether
[   64.430908] usbcore: registered new interface driver dm9601
[   64.436645] usbcore: registered new interface driver smsc95xx
[   64.442535] usbcore: registered new interface driver gl620a
[   64.448272] usbcore: registered new interface driver net1080
[   64.454071] usbcore: registered new interface driver plusb
[   64.459686] usbcore: registered new interface driver rndis_host
[   64.465789] usbcore: registered new interface driver cdc_subset
[   64.471862] usbcore: registered new interface driver zaurus
[   64.477569] usbcore: registered new interface driver MOSCHIP usb-ethe
rnet driver
[   64.485656] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Drive
r
[   64.492553] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
[   64.498626] ehci-omap ehci-omap.0: new USB bus registered, assigned b
us number 2
[   64.506256] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
[   64.526306] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
[   64.532226] usb usb2: New USB device found, idVendor=1d6b, idProduct=
0002
[   64.539123] usb usb2: New USB device strings: Mfr=3, Product=2, Seria
lNumber=1
[   64.546447] usb usb2: Product: OMAP-EHCI Host Controller
[   64.551818] usb usb2: Manufacturer: Linux 2.6.32 ehci_hcd
[   64.557281] usb usb2: SerialNumber: ehci-omap.0
[   64.562561] hub 2-0:1.0: USB hub found
[   64.566436] hub 2-0:1.0: 3 ports detected
[   64.596832] Initializing USB Mass Storage driver...
[   64.601928] usbcore: registered new interface driver usb-storage
[   64.608032] USB Mass Storage support registered.
[   64.613067] mice: PS/2 mouse device common for all mice
[   64.618774] input: gpio-keys as /devices/platform/gpio-keys/input/inp
ut0
[   64.626617] input: twl4030_pwrbutton as /devices/platform/i2c_omap.1/
i2c-1/1-0049/twl4030_pwrbutton/input/input1
[   64.637390] i2c /dev entries driver
[   64.641510] Linux video capture interface: v2.00
[   64.646514] omap-iommu omap-iommu.0: isp: version 1.1
[   64.652923] vpfe_init
[   64.655822] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
[   64.768951] mmci-omap-hs mmci-omap-hs.1: err -16 configuring card det
ect
[   64.776031] Registered led device: beagleboard::usr0
[   64.781219] Registered led device: beagleboard::usr1
[   64.787811] Registered led device: beagleboard::pmu_stat
[   64.794921] usbcore: registered new interface driver usbhid
[   64.800598] usbhid: USB HID core driver
[   64.804656] Advanced Linux Sound Architecture Driver Version 1.0.21.
[   64.811584] usbcore: registered new interface driver snd-usb-audio
[   64.894653] usb 2-2: new high speed USB device using ehci-omap and ad
dress 2
[   64.905975] No device for DAI omap-mcbsp-dai-0
[   64.910522] No device for DAI omap-mcbsp-dai-1
[   64.915008] No device for DAI omap-mcbsp-dai-2
[   64.919525] No device for DAI omap-mcbsp-dai-3
[   64.924041] No device for DAI omap-mcbsp-dai-4
[   64.928558] OMAP3 Beagle SoC init
[   64.932769] asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok
[   64.944274] ALSA device list:
[   64.947326]   #0: omap3beagle (twl4030)
[   64.951324] oprofile: using arm/armv7
[   64.955261] TCP cubic registered
[   64.958587] NET: Registered protocol family 17
[   64.963134] NET: Registered protocol family 15
[   64.967742] lib80211: common routines for IEEE802.11 drivers
[   64.973510] ThumbEE CPU extension supported.
[   64.977813] Power Management for TI OMAP3.
[   64.983245] Unable to set L3 frequency (400000000)
[   64.988189] Switched to new clocking rate (Crystal/Core/MPU): 26.0/33
2/1000 MHz
[   64.995574] IVA2 clocking rate: 800 MHz
[   65.166931] SmartReflex driver initialized
[   65.171173] omap3beaglelmb: Driver registration complete
[   65.181884] VFP support v0.3: implementor 41 architecture 3 part 30 v
ariant c rev 3
[   65.190185] registered taskstats version 1
[   65.195037] fbcvt: 1024x768@60: CVT Name - .786M3-R
[   65.229797] usb 2-2: New USB device found, idVendor=0424, idProduct=9
514
[   65.236572] usb 2-2: New USB device strings: Mfr=0, Product=0, Serial
Number=0
[   65.245117] hub 2-2:1.0: USB hub found
[   65.249023] hub 2-2:1.0: 5 ports detected
[   65.318450] Console: switching to colour frame buffer device 128x48
[   65.334167] regulator_init_complete: incomplete constraints, leaving
VAUX4 on
[   65.341735] regulator_init_complete: incomplete constraints, leaving
VAUX3 on
[   65.349182] regulator_init_complete: incomplete constraints, leaving
VDAC on
[   65.356903] omap_vout omap_vout: probed for an unknown device
[   65.363647] RAMDISK: gzip image found at block 0
[   65.527130] mmc0: new high speed SDHC card at address 1234
[   65.542602] mmcblk0: mmc0:1234 SA04G 3.67 GiB
[   65.547485]  mmcblk0:
[   65.550079] usb 2-2.1: new high speed USB device using ehci-omap and
address 3
[   65.565948]  p1 p2
[   65.683807] usb 2-2.1: New USB device found, idVendor=0424, idProduct
=ec00
[   65.698577] usb 2-2.1: New USB device strings: Mfr=0, Product=0, Seri
alNumber=0
[   65.718475] smsc95xx v1.0.4
[   65.807220] usb0: register 'smsc95xx' at usb-ehci-omap.0-2.1, smsc95x
x USB 2.0 Ethernet, 66:92:cf:63:c6:d4
[   67.996215] VFS: Mounted root (ext2 filesystem) on device 1:0.
[   68.004730] devtmpfs: mounted
[   68.010192] Freeing init memory: 204K
INIT: version 2.86 booting
Please wait: booting...
Starting udev
[   70.188323] FAT: bogus number of reserved sectors
[   70.195617] VFS: Can't find a valid FAT filesystem on dev mmcblk0.
[   70.586090] FAT: bogus number of reserved sectors
[   70.593414] VFS: Can't find a valid FAT filesystem on dev mmcblk0p2.
Remounting root file system...
Caching udev devnodes
Populating dev cache
Configuring network interfaces... ifconfig: SIOCGIFFLAGS: No such device
udhcpc (v1.13.2) started
Sending discover...
[   72.990844] usb0: link up, 100Mbps, full-duplex, lpa 0xCDE1
Sending discover...
Sending select for 192.168.101.101...
Lease of 192.168.101.101 obtained, lease time 600
done.
Setting up IP spoofing protection: rp_filter.
hwclock: can't open '/dev/misc/rtc': No such file or directory
Fri Aug 20 20:54:00 UTC 2010
hwclock: can't open '/dev/misc/rtc': No such file or directory
Configuring update-modules.
Configuring ti-dsplink-module.
Configuring ti-lpm-module.
Configuring util-linux-ng.
update-alternatives: Linking //bin/dmesg to dmesg.util-linux-ng
update-alternatives: Linking //bin/kill to kill.util-linux-ng
update-alternatives: Linking //bin/more to more.util-linux-ng
update-alternatives: Linking //sbin/mkswap to mkswap.util-linux-ng
[   75.417419] Alignment trap in kernel: sed (917) PC=0xc04363a0 Instr=0
xe8930003 Address=0xcc3f802a FSR 0x001
update-alternatives: Linking //sbin/pivot_root to pivot_root.util-linux-
ng
update-alternatives: Linking //sbin/sln to sln.util-linux-ng
update-alternatives: Linking //sbin/mkfs.minix to mkfs.minix.util-linux-
ng
update-alternatives: Linking //sbin/fsck.minix to fsck.minix.util-linux-
ng
update-alternatives: Linking //usr/bin/hexdump to hexdump.util-linux-ng
update-alternatives: Linking //usr/bin/last to last.sysvinit
update-alternatives: Linking //usr/bin/logger to logger.util-linux-ng
update-alternatives: Linking //usr/bin/mesg to mesg.sysvinit
update-alternatives: Linking //usr/bin/renice to renice.util-linux-ng
update-alternatives: Linking //usr/bin/wall to wall.sysvinit
update-alternatives: Linking //usr/bin/chfn to chfn.util-linux-ng
update-alternatives: Linking //usr/bin/newgrp to newgrp.util-linux-ng
update-alternatives: Linking //usr/bin/chsh to chsh.util-linux-ng
update-alternatives: Linking //bin/login to login.util-linux-ng
update-alternatives: Error: not linking //sbin/vipw to vipw.util-linux-n
g since //sbin/vipw exists and is not a link
update-alternatives: Linking //sbin/vigr to vigr.util-linux-ng
update-alternatives: Linking //usr/bin/reset to reset.util-linux-ng
update-alternatives: Linking //usr/bin/setsid to setsid.util-linux-ng
update-alternatives: Linking //usr/bin/chrt to chrt.util-linux-ng
update-alternatives: Linking //sbin/hwclock to ../bin/busybox
update-alternatives: Linking //sbin/shutdown to shutdown.sysvinit
update-alternatives: Linking //sbin/reboot to reboot.sysvinit
update-alternatives: Linking //sbin/halt to halt.sysvinit
INIT: Entering runlevel: 5
Creating Dropbear SSH server RSA host key.
Will output 1024 bit rsa secret key to '/etc/dropbear/dropbear_rsa_host_
key'
Generating key, this may take a while...
Public key portion is:
ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAAAgwCcpuxDpaRpSCJQO0gt8z69CVV8VnaE4GTS
tMhRZmHrWs8384NXSAyX3Os4cNmTuf+fhoduIIzbXSJbyjHB58k+JbG8cfpwOtH+NYNoKPY5
gk7qyutK3j7B9KqpzIJaMZ6vvmUf/31MzG12DFycLAQhd2VTkWdGn8gcNrbZraotabTB roo
t@beagleboard
Fingerprint: md5 65:70:ac:28:4c:f2:7f:2d:95:ef:fe:45:62:b8:63:21
Starting Dropbear SSH server: dropbear.
Starting syslogd/klogd: done

.-------.
|       |                  .-.
|   |   |-----.-----.-----.| |   .----..-----.-----.
|       |     | __  |  ---'| '--.|  .-'|     |     |
|   |   |  |  |     |---  ||  --'|  |  |  '  | | | |
'---'---'--'--'--.  |-----''----''--'  '-----'-'-'-'
                -'  |
                '---'

The Angstrom Distribution beagleboard ttyS2

Angstrom 2010.7-test-20100820 beagleboard ttyS2

beagleboard login: