Instantly share code, notes, and snippets.

Embed
What would you like to do?
BeagleBoard-xM 2.6.38-rc8 Kernel Boot - CLFS Embedded Toolchain
Texas Instruments X-Loader 1.4.4ss (Aug 19 2010 - 02:49:27)
Beagle xM Rev A
Reading boot sector
Loading u-boot.bin from mmc
U-Boot 2010.03-dirty (Aug 20 2010 - 20:50:46)
OMAP3630/3730-GP ES2.0, CPU-OPP2, L3-165MHz,
OMAP3 Beagle board + LPDDR/NAND
I2C: ready
DRAM: 512 MB
NAND: 0 MiB
*** Warning - bad CRC or NAND, using default environment
In: serial
Out: serial
Err: serial
Probing for expansion boards, if none are connected you'll see a harmles
s I2C error.
No EEPROM on expansion board
Beagle xM Rev A
Die ID #146000011ff00000015739eb0b021002
Hit any key to stop autoboot: 0
OMAP3 beagleboard.org # setenv console ttyO2,115200n8
OMAP3 beagleboard.org # mmc init ${mmcdev}
mmc1 is available
OMAP3 beagleboard.org # run loaduimage
reading uImage
2990964 bytes read
OMAP3 beagleboard.org # run mmcboot
Booting from mmc ...
## Booting kernel from Legacy Image at 80200000 ...
Image Name: Linux-2.6.38-rc8-09493-gd6f5a6e
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2990900 Bytes = 2.9 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Linux version 2.6.38-rc8-09493-gd6f5a6e (clfs-embedded-ar
m@bigbox) (gcc version 4.5.2 (GCC) ) #3 SMP Mon Mar 14 06:53:21 EDT 2011
[ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10
c53c7f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instructi
on cache
[ 0.000000] Machine: OMAP3 Beagle Board
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] OMAP3630 ES1.1 (l2cache iva sgx neon isp 192mhz_clk )
[ 0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x10000
[ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/600 MHz
[ 0.000000] Reprogramming SDRC clock to 332000000 Hz
[ 0.000000] PERCPU: Embedded 7 pages/cpu @c0f68000 s8192 r8192 d12288
u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. T
otal pages: 130048
[ 0.000000] Kernel command line: console=ttyO2,115200n8 mpurate=1000
buddy=none camera=lbcm3m1 vram=12M omapfb.mode=dvi:640x480MR-16@60 omapd
ss.def_disp=dvi root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144
bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 b
ytes)
[ 0.000000] Memory: 512MB = 512MB total
[ 0.000000] Memory: 508088k/508088k available, 16200k reserved, 0K hi
ghmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
[ 0.000000] vmalloc : 0xe0800000 - 0xf8000000 ( 376 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .init : 0xc0008000 - 0xc0052000 ( 296 kB)
[ 0.000000] .text : 0xc0052000 - 0xc058f9dc (5367 kB)
[ 0.000000] .data : 0xc0590000 - 0xc0608360 ( 481 kB)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] NR_IRQS:409
[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 i
nterrupts
[ 0.000000] Total of 96 interrupts on 1 active controller
[ 0.000000] omap_hwmod: gpt12_fck: missing clockdomain for gpt12_fck.
[ 0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz
[ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps
every 131071999ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, In
c., Ingo Molnar
[ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8
[ 0.000000] ... MAX_LOCK_DEPTH: 48
[ 0.000000] ... MAX_LOCKDEP_KEYS: 8191
[ 0.000000] ... CLASSHASH_SIZE: 4096
[ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384
[ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768
[ 0.000000] ... CHAINHASH_SIZE: 16384
[ 0.000000] memory used by lock dependency info: 3695 kB
[ 0.000000] per task-struct memory footprint: 1152 bytes
[ 0.000885] Calibrating delay loop... 478.91 BogoMIPS (lpj=1867776)
[ 0.143981] pid_max: default: 32768 minimum: 301
[ 0.144714] Security Framework initialized
[ 0.145080] Mount-cache hash table entries: 512
[ 0.149139] CPU: Testing write buffer coherency: ok
[ 0.150024] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5
counters available
[ 0.151824] Brought up 1 CPUs
[ 0.151855] SMP: Total of 1 processors activated (478.91 BogoMIPS).
[ 0.164428] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for
l3_main
[ 0.164428] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for
l4_core
[ 0.164459] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for
l4_per
[ 0.164489] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for
l4_wkup
[ 0.171173] print_constraints: dummy:
[ 0.172454] NET: Registered protocol family 16
[ 0.172729] GPMC revision 5.0
[ 0.172851] Trying to install interrupt handler for IRQ402
[ 0.172882] Trying to install interrupt handler for IRQ403
[ 0.172882] Trying to install interrupt handler for IRQ404
[ 0.172912] Trying to install interrupt handler for IRQ405
[ 0.172943] Trying to install interrupt handler for IRQ406
[ 0.172943] Trying to install interrupt handler for IRQ407
[ 0.172973] Trying to install interrupt handler for IRQ408
[ 0.173004] Trying to install type control for IRQ409
[ 0.173004] Trying to set irq flags for IRQ409
[ 0.180236] omap_device: omap_gpio.0: new worst case activate latency
0: 91552
[ 0.180847] OMAP GPIO hardware version 2.5
[ 0.181365] OMAP GPIO hardware version 2.5
[ 0.182037] OMAP GPIO hardware version 2.5
[ 0.182495] OMAP GPIO hardware version 2.5
[ 0.182922] OMAP GPIO hardware version 2.5
[ 0.183380] OMAP GPIO hardware version 2.5
[ 0.196258] omap_mux_init: Add partition: #1: core, flags: 0
[ 0.199005] OMAP3 Beagle Rev: xM
[ 0.204650] omap_device: omap_uart.1: new worst case activate latency
0: 30517
[ 0.205108] omap_device: omap_uart.1: new worst case deactivate laten
cy 0: 30517
[ 0.207824] Found NAND on CS0
[ 0.207824] Registering NAND on CS0
[ 0.208923] Unable to get DVI reset GPIO
[ 0.208984] hw-breakpoint: debug architecture 0x4 unsupported.
[ 0.224884] ------------[ cut here ]------------
[ 0.224914] WARNING: at arch/arm/mach-omap2/clock.c:438 omap2_clk_swi
tch_mpurate_at_boot+0x7c/0xb4()
[ 0.224945] clock: dpll1_ck: unable to set MPU rate to 1000: -22
[ 0.224975] Modules linked in:
[ 0.225006] [<c0063aa0>] (unwind_backtrace+0x0/0xe4) from [<c0096c0c>
] (warn_slowpath_common+0x4c/0x64)
[ 0.225036] [<c0096c0c>] (warn_slowpath_common+0x4c/0x64) from [<c009
6ca4>] (warn_slowpath_fmt+0x2c/0x3c)
[ 0.225067] [<c0096ca4>] (warn_slowpath_fmt+0x2c/0x3c) from [<c00143e
c>] (omap2_clk_switch_mpurate_at_boot+0x7c/0xb4)
[ 0.225097] [<c00143ec>] (omap2_clk_switch_mpurate_at_boot+0x7c/0xb4)
from [<c00149f0>] (omap3xxx_clk_arch_init+0x20/0x50)
[ 0.225158] [<c00149f0>] (omap3xxx_clk_arch_init+0x20/0x50) from [<c0
05264c>] (do_one_initcall+0xbc/0x194)
[ 0.225189] [<c005264c>] (do_one_initcall+0xbc/0x194) from [<c0008dec
>] (kernel_init+0x158/0x21c)
[ 0.225219] [<c0008dec>] (kernel_init+0x158/0x21c) from [<c005d5a4>]
(kernel_thread_exit+0x0/0x8)
[ 0.225769] ---[ end trace 1b75b31a2719ed1c ]---
[ 0.227203] OMAP DMA hardware revision 5.0
[ 0.285400] bio: create slab <bio-0> at 0
[ 0.294647] SCSI subsystem initialized
[ 0.295227] omap_device: omap2_mcspi.1: new worst case activate laten
cy 0: 30517
[ 0.299774] omap_device: omap2_mcspi.4: new worst case deactivate lat
ency 0: 30517
[ 0.303405] usbcore: registered new interface driver usbfs
[ 0.304504] usbcore: registered new interface driver hub
[ 0.305358] usbcore: registered new device driver usb
[ 0.307434] omap_device: omap_i2c.1: new worst case activate latency
0: 30517
[ 0.307617] omap_i2c omap_i2c.1: bus 1 rev1.4.0 at 2600 kHz
[ 0.317779] twl4030: PIH (irq 7) chaining IRQs 368..375
[ 0.317901] twl4030: power (irq 373) chaining IRQs 376..383
[ 0.320068] twl4030: gpio (irq 368) chaining IRQs 384..401
[ 0.331970] print_constraints: VMMC1: 1850 <--> 3150 mV at 3000 mV no
rmal standby
[ 0.334411] print_constraints: VDAC: 1800 mV normal standby
[ 0.336975] print_constraints: VDVI: 1800 mV normal standby
[ 0.339813] print_constraints: VSIM: 1800 <--> 3000 mV at 1800 mV nor
mal standby
[ 0.340484] omap_device: omap_i2c.1: new worst case deactivate latenc
y 0: 30517
[ 0.340759] omap_i2c omap_i2c.3: bus 3 rev1.4.0 at 100 kHz
[ 0.350952] Switching to clocksource 32k_counter
[ 0.356994] Switched to NOHz mode on CPU #0
[ 0.458099] NET: Registered protocol family 2
[ 0.458740] IP route cache hash table entries: 4096 (order: 2, 16384
bytes)
[ 0.460693] TCP established hash table entries: 16384 (order: 5, 1310
72 bytes)
[ 0.461761] TCP bind hash table entries: 16384 (order: 7, 589824 byte
s)
[ 0.471008] TCP: Hash tables configured (established 16384 bind 16384
)
[ 0.471099] TCP reno registered
[ 0.471130] UDP hash table entries: 256 (order: 2, 20480 bytes)
[ 0.471466] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes)
[ 0.472534] NET: Registered protocol family 1
[ 0.473846] RPC: Registered udp transport module.
[ 0.473876] RPC: Registered tcp transport module.
[ 0.473907] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.474853] NetWinder Floating Point Emulator V0.97 (double precision
)
[ 0.481506] PMU: registered new PMU device of type 0
[ 0.642242] VFS: Disk quotas dquot_6.5.2
[ 0.642639] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes
)
[ 0.645172] JFFS2 version 2.2. (NAND) (SUMMARY) �© 2001-2006 Red Hat
, Inc.
[ 0.646301] msgmni has been set to 992
[ 0.651000] io scheduler noop registered
[ 0.651031] io scheduler deadline registered
[ 0.651275] io scheduler cfq registered (default)
[ 0.655517] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.662780] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMA
P UART0
[ 0.664855] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMA
P UART1
[ 0.666046] omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a OMA
P UART2
[ 1.537902] console [ttyO2] enabled
[ 1.543395] omap_uart.3: ttyO3 at MMIO 0x49042000 (irq = 80) is a OMA
P UART3
[ 1.590026] brd: module loaded
[ 1.611785] loop: module loaded
[ 1.616149] omap_device: omap_i2c.1: new worst case activate latency
0: 91552
[ 1.631713] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 1.638732] omap2-nand driver initializing
[ 1.643585] No NAND device found.
[ 1.647308] No NAND device found.
[ 1.651702] OneNAND driver initializing
[ 1.664184] usbcore: registered new interface driver asix
[ 1.670440] usbcore: registered new interface driver cdc_ether
[ 1.677459] usbcore: registered new interface driver net1080
[ 1.684082] usbcore: registered new interface driver cdc_subset
[ 1.690979] usbcore: registered new interface driver zaurus
[ 1.696929] cdc_ncm: 7-Feb-2011
[ 1.700805] usbcore: registered new interface driver cdc_ncm
[ 1.709228] usbcore: registered new interface driver cdc_wdm
[ 1.715270] Initializing USB Mass Storage driver...
[ 1.721069] usbcore: registered new interface driver usb-storage
[ 1.727508] USB Mass Storage support registered.
[ 1.733612] usbcore: registered new interface driver libusual
[ 1.740356] usbcore: registered new interface driver usbtest
[ 1.746398] udc: OMAP UDC driver, version: 4 October 2004 (iso) (dma)
[ 1.756652] mousedev: PS/2 mouse device common for all mice
[ 1.765747] input: gpio-keys as /devices/platform/gpio-keys/input/inp
ut0
[ 1.781433] input: twl4030_pwrbutton as /devices/platform/omap/omap_i
2c.1/i2c-1/1-0049/twl4030_pwrbutton/input/input1
[ 1.796417] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
[ 1.805419] i2c /dev entries driver
[ 1.813629] Driver for 1-wire Dallas network protocol.
[ 1.821197] omap_device: omap_wdt.-1: new worst case activate latency
0: 30517
[ 1.830474] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
[ 1.836975] omap_device: omap_wdt.-1: new worst case deactivate laten
cy 0: 30517
[ 1.845794] twl4030_wdt twl4030_wdt: Failed to register misc device
[ 1.852539] twl4030_wdt: probe of twl4030_wdt failed with error -16
[ 1.873138] usbcore: registered new interface driver usbhid
[ 1.879211] usbhid: USB HID core driver
[ 1.885040] oprofile: using arm/armv7
[ 1.889556] TCP cubic registered
[ 1.893188] Initializing XFRM netlink socket
[ 1.897827] NET: Registered protocol family 17
[ 1.902648] NET: Registered protocol family 15
[ 1.907775] Registering the dns_resolver key type
[ 1.913330] VFP support v0.3: implementor 41 architecture 3 part 30 v
ariant c rev 3
[ 1.923370] ThumbEE CPU extension supported.
[ 1.938629] Power Management for TI OMAP3.
[ 1.978881] clock: disabling unused clocks to save power
[ 1.989776] regulator_init_complete: VDVI: incomplete constraints, le
aving on
[ 1.997711] regulator_init_complete: VDAC: incomplete constraints, le
aving on
[ 2.006622] twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00
:45 UTC (946684845)
[ 2.018432] Waiting for root device /dev/mmcblk0p2...
[ 2.227020] mmc0: host does not support reading read-only switch. ass
uming write-enable.
[ 2.249908] mmc0: new high speed SDHC card at address 1234
[ 2.259002] mmcblk0: mmc0:1234 SA04G 3.67 GiB
[ 2.270172] mmcblk0: p1 p2
[ 2.367218] List of all partitions:
[ 2.370971] b300 3858432 mmcblk0 driver: mmcblk
[ 2.376647] b301 120456 mmcblk0p1 00000000-0000-0000-0000-
000000000000mmcblk0p1
[ 2.385375] b302 8032 mmcblk0p2 00000000-0000-0000-0000-
000000000000mmcblk0p2
[ 2.394104] No filesystem could mount root, tried: ext3
[ 2.399719] Kernel panic - not syncing: VFS: Unable to mount root fs
on unknown-block(179,2)
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment