-
-
Save braian87b/bba9da3a7ac23c35b7f1eecafecdd47d to your computer and use it in GitHub Desktop.
# ======================================================== | |
# Setup a Dumb AP, Wired backbone for OpenWRT / LEDE | |
# ======================================================== | |
# Set lan logical interface as bridge (to allow bridge multiple physical interfaces) | |
uci set network.lan.type='bridge' | |
# assign WAN physical interface to LAN (will be available as an additional LAN port now) | |
uci set network.lan.ifname="$(uci get network.lan.ifname) $(uci get network.wan.ifname)" | |
uci del network.wan.ifname | |
# Remove wan logical interface, since we will not need it. | |
uci del network.wan | |
# Disable Dnsmasq completely (it is important to commit or discard dhcp) | |
uci commit dhcp; echo '' > /etc/config/dhcp | |
/etc/init.d/dnsmasq disable | |
/etc/init.d/dnsmasq stop | |
# Set static network configuration (sample config for 192.168.1.0/24) | |
# 192.168.1.1 is the Main Router | |
uci set network.lan.ipaddr='192.168.1.2' | |
uci set network.lan.dns='192.168.1.1' | |
uci set network.lan.gateway='192.168.1.1' | |
uci set network.lan.netmask='255.255.255.0' | |
uci set network.lan.broadcast='192.168.1.255' | |
# Set DHCP on LAN (not recommended, but useful when Dumb AP is moveable from one building to another) | |
uci del network.lan.broadcast | |
uci del network.lan.dns | |
uci del network.lan.gateway | |
uci del network.lan.ipaddr | |
uci del network.lan.netmask | |
uci set network.lan.proto='dhcp' | |
# To identify better when connected to SSH and when seen on the network | |
uci set system.@system[0].hostname='DumbAP1' | |
uci set network.lan.hostname="`uci get system.@system[0].hostname`" | |
# ======================================================== | |
# Optional, Disable IPv6 | |
# ======================================================== | |
uci del network.lan.ip6assign | |
uci set network.lan.delegate='0' | |
uci del dhcp.lan.dhcpv6 | |
uci del dhcp.lan.ra | |
uci del dhcp.odhcpd | |
/etc/init.d/odhcpd disable | |
/etc/init.d/odhcpd stop | |
# ======================================================== | |
# Commit changes, flush, and restart network | |
# ======================================================== | |
# This way we will get internet on this AP and we must reconnect | |
uci commit | |
sync | |
/etc/init.d/network restart | |
# If all is OK then reboot and test again: | |
reboot | |
# How to setup Wireless Links to avoid Wired backbone using WDS on Atheros for OpenWRT / LEDE | |
https://gist.github.com/braian87b/8a524a8ad74a36407a8f481e9d16a5c9 | |
# How to setup Client Bridged / Client Mode / RelayD and IGMPProxy for OpenWRT / LEDE | |
https://gist.github.com/braian87b/821e9e4f399918510c55619192a31871 |
Hi @braian87b
Thanks for your help.
Based on your script, and after many tests, I've created the following script, can you please take a quick look?
Please let me know if something wrong in it.
# ========================================================
# Setup a Dumb AP for OpenWRT
# Tested on: Belkin RT3200 (aka. Linksys E8450) 22.03.3
# Script expects factory settings
# ========================================================
# Disable IPv6
# ========================================================
uci delete network.lan.ip6assign
uci set network.lan.delegate='0'
uci delete dhcp.lan.dhcpv6
uci delete dhcp.lan.ra
uci delete dhcp.odhcpd
/etc/init.d/odhcpd disable
/etc/init.d/odhcpd stop
uci delete network.globals.ula_prefix
uci commit
# ========================================================
# Disable Dnsmasq completely and discard dhcp
uci commit dhcp; echo '' > /etc/config/dhcp
/etc/init.d/dnsmasq disable
/etc/init.d/dnsmasq stop
# ========================================================
# Disable firewall
/etc/init.d/firewall disable
/etc/init.d/firewall stop
mv /etc/config/firewall /etc/config/firewall.unused
# ========================================================
# Remove WAN logical interfaces
uci delete network.wan
uci delete network.wan6
# ========================================================
# To identify better when connected to SSH and when seen on the network
uci set system.@system[0].hostname='DumbAP'
uci set network.lan.hostname="`uci get system.@system[0].hostname`"
uci commit system
# ========================================================
# Set static network configuration (sample config for 192.168.1.0/24)
# 192.168.1.1 is the Main Router
# ========================================================
uci set network.lan.ipaddr='192.168.1.2'
uci set network.lan.dns='192.168.1.1'
uci set network.lan.gateway='192.168.1.1'
uci set network.lan.netmask='255.255.255.0'
uci set network.lan.broadcast='192.168.1.255'
uci commit network
echo '====================================================================='
echo 'Reboot your router'
echo 'you can now connect the LAN port of this device to the LAN port'
echo 'of your main router.'
echo '192.168.1.2 is now your Access Point IP Address'
echo '====================================================================='
sync
reboot
Notes:
1- Adding WAN physical interface to LAN did not work in my router!, I had to do it manually in LuCi :(
using "network.lan.ifname" is not working anymore, I think now it is "network.lan.device"
If I type: "uci show network" then this is the result:
root@OpenWrt:~# uci show network
network.loopback=interface
network.loopback.device='lo'
network.loopback.proto='static'
network.loopback.ipaddr='127.0.0.1'
network.loopback.netmask='255.0.0.0'
network.globals=globals
network.globals.ula_prefix=''
network.@device[0]=device
network.@device[0].name='br-lan'
network.@device[0].type='bridge'
network.@device[0].ports='lan1' 'lan2' 'lan3' 'lan4'
network.lan=interface
network.lan.device='br-lan'
network.lan.proto='static'
network.lan.ipaddr='192.168.1.1'
network.lan.netmask='255.255.255.0'
network.lan.ip6assign='60'
network.wan=interface
network.wan.device='wan'
network.wan.proto='dhcp'
network.wan6=interface
network.wan6.device='wan'
network.wan6.proto='dhcpv6'
2-The only thing that I could not disable is "Enable IPv6" from the configuration of the "bridge device" under "General device options" tab
do you know the command to do that? Or maybe it is not necessary anymore? I've tried Google without any luck! Please check the screenshot attached:
Try not remove /etc/config/firewall
file placeholder, leave it as-is, disabling the service is enough, you will not save space since that starts sitting in rom, but you can empty the file if you want, similarly as with /etc/config/dhcp
if you want it cleaner.
remember that if you are using recent version of openwrt it won't have swconfig
anymore now it uses DSA. so the configuration will be different,
IPv6 you can disable using Luci and see on the pending settings to be commit which changed.
You can always change everything using LuCI and inspect which changes LuCi do and dump those into your script, will be safer if you are not familiar yet with all the configurations.
I greatly appreciate your help and efforts @braian87b
@RustyRouter happy to help.
@RustyRouter
(A) yes, either, since you cannot do the both, unless you create a 2nd bridged interface to the lan, think about it as for any device on your network (phone, computer, etc) you can configure a static IP or use DHCP, static IP is useful if you want to tie an IP to the device no matter on which network... but preferable you can use DHCP and set an static lease for the AP macaddress so the main Router will provide always the same IP to the dumb AP.
(B)
mostly involves the steps above, and also you can do the same on your main router and additionally disable ipv6 on the wan side if you have reliable ipv4 and don't want ISP ipv6
if you want to go deeper:
https://www.google.com/search?q=openwrt+disable+ipv6
this one seems pretty accurate on all needed: https://3os.org/infrastructure/openwrt/disable-ipv6/
.