Blog 2022/8/7
<- previous | index | next ->
Here is an Arduino sketch which reads values
dreamcat4
/ vpn.sh
Created
November 8, 2023 21:55
— forked from bluewalk/vpn.sh
VPN.SH script to tunnel specific VLAN through a WireGuard tunnel on an UDM Pro
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| #!/bin/sh | |
| INTERFACE="vpn0" | |
| MARK=100 | |
| TABLE="vpn" | |
| SCRIPT_NAME="/etc/wireguard/scripts/vpn.sh" | |
| # set this to the interface(s) on which you want WAN traffic to | |
| # be routed through vpn. separate interfaces with spaces. | |
| # e.g. "br0" or "br0 br1" etc. |
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| #!/bin/sh | |
| INTERFACE="vpn0" | |
| MARK=100 | |
| TABLE="vpn" | |
| SCRIPT_NAME="/etc/wireguard/scripts/vpn.sh" | |
| # set this to the interface(s) on which you want WAN traffic to | |
| # be routed through vpn. separate interfaces with spaces. | |
| # e.g. "br0" or "br0 br1" etc. |
bluewalk
/ GetNordVPNWireGuardDetails.md
Last active
May 6, 2024 01:14
Getting NordVPN WireGuard details
Instructions to obtain WireGuard details of your NordVPN account. These can be used to setup a WireGuard tunnel on your router to NordVPN.
Source: https://forum.gl-inet.com/t/configure-wireguard-client-to-connect-to-nordvpn-servers/10422/27
If you have any linux machine, use that or install a vm if you don't have one.
Get their official linux app installed. Make sure you have wireguard installed too. And set the used technology to Nordlynx by running nordvpn set technology nordlynx
When building plugins for Linux there are two options and one problem:
- Link to the system libraries
- Build all your dependencies and statically link to them
- Can't use gtk or qt.
ansemjo
/ Otterpill-Blink.md
Last active
May 26, 2020 16:16
minimal blink exmaple for the otterpill with platformio and the stm32cube-hal
I looked into PlatformIO usage with the STM32 series after going thorugh Jan Hendrik's Otterpill workshop. This is the absolutely minimal blink exmaple.
It remains unclear to me how or if I could use a configuration that was generated with CubeMX in a PlatformIO project.
See Using STM32CubeMX with PlatformIO (archive) on how to import CubeMX configuration into your project or use stm32pio.
- Create the files
platformio.iniandsrc/main.cfrom the sources above.
I'm able to get a Void Linux image (32bit, raspberry pi 2 image) to boot on the
raspberry pi 4. Currently, I can get it to boot and even handle upgrading via
xbps-install -Su (networked over ethernet), however I can't seem to get it to
see the internal wlan (wifi) device.
huge shout out to kodifies on this reddit post for helping me to get this going.
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| <?xml version="1.0" encoding="UTF-8"?> | |
| <!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd"> | |
| <plist version="1.0"> | |
| <dict> | |
| <!-- IKEv2 IPSec VPN profile for Apple devices, Pre-Shared Key(PSK), no username password. | |
| References: | |
| https://wiki.strongswan.org/projects/strongswan/wiki/AppleIKEv2Profile | |
| https://developer.apple.com/library/mac/featuredarticles/iPhoneConfigurationProfileRef/Introduction/Introduction.html | |
| https://help.apple.com/configurator | |
| The extension of this file should be .mobileconfig --> |
hluaces
/ testio.sh
Created
January 23, 2019 17:59
— forked from jsandas/testio.sh
Disk IO test for linux
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| #!/bin/bash | |
| # References | |
| # https://devopsideas.com/benchmarking-disk-iops-aws-vs-digitalocean/ | |
| # https://wiki.mikejung.biz/Benchmarking#Fio_Test_Options_and_Examples | |
| # https://tobert.github.io/post/2014-04-17-fio-output-explained.html | |
| # Requires linux packages: fio ioping |
metacollin
/ Polycarbonate.ini
Last active
May 6, 2024 10:17
Slic3r settings for high quality, low-warp, high-strength printing of polycarbonate without an enclosure on a Prusa i3 MK2S
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| # generated by Slic3r 1.37.2-prusa3d on Thu Dec 7 09:48:20 2017 | |
| # Figured out by trial and error engineer metacollin | |
| # Released as public domain. | |
| # USE GLUESTICK FOR PRINT BED ADHESION | |
| avoid_crossing_perimeters = 0 | |
| bed_shape = 0x0,250x0,250x210,0x210 | |
| bed_temperature = 110 | |
| before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;[layer_z]\n\n | |
| bottom_solid_layers = 8 | |
| bridge_acceleration = 1000 |
NewerOlder