Skip to content

Instantly share code, notes, and snippets.

@jmhebert

jmhebert/Nano boot log 2.txt

Created March 17, 2020 14:34
Show Gist options
  • Save jmhebert/4de459975bd433607298e5b9a151c3b5 to your computer and use it in GitHub Desktop.
Save jmhebert/4de459975bd433607298e5b9a151c3b5 to your computer and use it in GitHub Desktop.
Download ZIP
Nano boot from Serial Debug Console
Raw
Nano boot log 2.txt
[0000.157] [L4T TegraBoot] (version 00.00.2018.01-l4t-39a9dc3d)
[0000.163] Processing in cold boot mode Bootloader 2
[0000.167] A02 Bootrom Patch rev = 1023
[0000.171] Power-up reason: software reset
[0000.175] No Battery Present
[0000.177] pmic max77620 reset reason
[0000.181] pmic max77620 NVERC : 0x0
[0000.184] RamCode = 0
[0000.186] Platform has DDR4 type RAM
[0000.190] max77620 disabling SD1 Remote Sense
[0000.194] Setting DDR voltage to 1125mv
[0000.198] Serial Number of Pmic Max77663: 0x1727e5
[0000.206] Entering ramdump check
[0000.209] Get RamDumpCarveOut = 0x0
[0000.212] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8
[0000.217] Last reboot was clean, booting normally!
[0000.221] Sdram initialization is successful
[0000.226] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000
[0000.232] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000
[0000.237] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000
[0000.243] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000
[0000.249] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000
[0000.255] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000
[0000.261] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000
[0000.267] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000
[0000.283] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000
[0000.289] Platform-DebugCarveout: 0
[0000.292] Nck Carveout Base=0x00000000ff080000 Size=0x00200000
[0000.298] Non secure mode, and RB not enabled.
[0000.357] Csd NumOfBlocks=62423040
[0000.362] Set High speed to 1
[0000.368] Using GPT Primary to query partitions
[0000.373] Loading Tboot-CPU binary
[0000.382] Verifying TBC in OdmNonSecureSBK mode
[0000.392] Bootloader load address is 0xa0000000, entry address is 0xa0000258
[0000.399] Bootloader downloaded successfully.
[0000.403] Downloaded Tboot-CPU binary to 0xa0000258
[0000.408] MAX77620_GPIO5 configured
[0000.412] CPU power rail is up
[0000.415] CPU clock enabled
[0000.418] Performing RAM repair
[0000.421] Updating A64 Warmreset Address to 0xa00002e9
[0000.426] Loading NvTbootBootloaderDTB
[0000.451] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode
[0000.516] Bootloader DTB Load Address: 0x83000000
[0000.521] Loading NvTbootKernelDTB
[0000.545] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode
[0000.610] Kernel DTB Load Address: 0x83100000
[0000.615] Loading cboot binary
[0000.645] Verifying EBT in OdmNonSecureSBK mode
[0000.686] Bootloader load address is 0x92c00000, entry address is 0x92c00258
[0000.693] Bootloader downloaded successfully.
[0000.710] Using BFS PT to query partitions
[0000.714] Next binary entry address: 0x92c00258
[0000.719] BoardId: 3448
[0000.723] Overriding pmu board id with proc board id
[0000.728] Display board id is not available
[0000.756] Verifying SC7EntryFw in OdmNonSecureSBK mode
[0000.808] /bpmp deleted
[0000.810] SC7EntryFw header found loaded at 0xff700000
[0000.999] OVR2 PMIC
[0001.001] Bpmp FW successfully loaded
[0001.005] WB0 init successfully at 0xff780000
[0001.010] Set NvDecSticky Bits
[0001.013] GSC2 address ff53fffc value c0edbbcc
[0001.019] GSC MC Settings done
[0001.023] TOS Image length 53680
[0001.026] Monitor size 53680
[0001.029] OS size 0
[0001.036] Secure Os AES-CMAC Verification Success!
[0001.041] TOS image cipher info: plaintext
[0001.044] Loading and Validation of Secure OS Successful
[0001.060] SC7 Entry Firmware - 0xff700000, 0x4000
[0001.065] NvTbootPackSdramParams: start.
[0001.070] NvTbootPackSdramParams: done.
[0001.074] Tegraboot started after 85351 us
[0001.078] Basic modules init took 665062 us
[0001.082] Sec Bootdevice Read Time = 12 ms, Read Size = 65 KB
[0001.087] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB
[0001.093] Storage Device Read Time = 108 ms, Read Size = 2226 KB
[0001.099] Storage Device Write Time = 0 ms, Write Size = 0 KB
[0001.104] Next stage binary read took 24465 us
[0001.108] Carveout took -36129 us
[0001.111] CPU initialization took 361240 us
[0001.115] Total time taken by TegraBoot 1014638 us
[0001.120] Starting CPU & Halting co-processor
64NOTICE: BL31: v1.3(release):23b153a63
NOTICE: BL31: Built : 22:39:57, Dec 9 2019
ERROR: Error initializing runtime service trusty_fast
[0001.242] RamCode = 0
[0001.247] LPDDR4 Training: Read DT: Number of tables = 2
[0001.252] EMC Training (SRC-freq: 204000; DST-freq: 1600000)
[0001.265] EMC Training Successful
[0001.268] 408000 not found in DVFS table
[0001.274] RamCode = 0
[0001.278] DT Write: emc-table@204000 succeeded
[0001.283] DT Write: emc-table@1600000 succeeded
[0001.287] LPDDR4 Training: Write DT: Number of tables = 2
[0001.328]
[0001.329] Debug Init done
[0001.331] Marked DTB cacheable
[0001.334] Bootloader DTB loaded at 0x83000000
[0001.339] Marked DTB cacheable
[0001.342] Kernel DTB loaded at 0x83100000
[0001.346] DeviceTree Init done
[0001.361] Pinmux applied successfully
[0001.366] gicd_base: 0x50041000
[0001.369] gicc_base: 0x50042000
[0001.372] Interrupts Init done
[0001.376] Using base:0x60005090 & irq:208 for tick-timer
[0001.382] Using base:0x60005098 for delay-timer
[0001.386] platform_init_timer: DONE
[0001.389] Timer(tick) Init done
[0001.393] osc freq = 38400 khz
[0001.397]
[0001.398] Welcome to L4T Cboot
[0001.401]
[0001.403] Cboot Version: 00.00.2018.01-t210-40c3ff9c
[0001.408] calling constructors
[0001.410] initializing heap
[0001.413] initializing threads
[0001.416] initializing timers
[0001.419] creating bootstrap completion thread
[0001.423] top of bootstrap2()
[0001.426] CPU: ARM Cortex A57
[0001.429] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000
[0001.434] initializing platform
[0001.442] Manufacturer: MF = 0xc2, ID MSB = 0x25
[0001.446] ID LSB = 0x36, ID-CFI len = 194 bytes
[0001.450] Macronix QSPI chip present
[0001.454] SPI device register
[0001.457] init boot device
[0001.459] allocating memory for boot device(SPI)
[0001.464] registering boot device
[0001.473] sdmmc node status = okay
[0001.477] sdcard instance = 0
[0001.479] sdcard gpio handle 0x56
[0001.483] sdcard gpio pin 0xc9
[0001.486] sdcard gpio flags 0x0
[0001.489] vmmc-supply 0x99
[0001.491] Instance: 0
[0001.493] Allocating memory for context
[0001.497] enabling clock
[0001.500] sd card init
[0001.502] Check card present and stable
[0001.506] Send command 0
[0001.522] Send command 3
[0001.526] Set RCA for the card
[0001.529] Query card specific data by command 9
[0001.536] Parse CSD data
[0001.538] Send command 7
[0001.549] Calling sd device register
[0001.552] Init sdcard
[0001.554] Allocating memory for boot device
[0001.558] Registering user device
[0001.571] Enable APE clock
[0001.574] Un-powergate APE partition
[0001.578] of_register: registering tegra_udc to of_hal
[0001.583] of_register: registering inv20628-driver to of_hal
[0001.588] of_register: registering ads1015-driver to of_hal
[0001.594] of_register: registering lp8557-bl-driver to of_hal
[0001.600] of_register: registering bq2419x_charger to of_hal
[0001.605] of_register: registering bq27441_fuel_gauge to of_hal
[0001.617] gpio framework initialized
[0001.620] of_register: registering tca9539_gpio to of_hal
[0001.626] of_register: registering tca9539_gpio to of_hal
[0001.631] of_register: registering i2c_bus_driver to of_hal
[0001.636] of_register: registering i2c_bus_driver to of_hal
[0001.642] of_register: registering i2c_bus_driver to of_hal
[0001.648] pmic framework initialized
[0001.651] of_register: registering max77620_pmic to of_hal
[0001.657] regulator framework initialized
[0001.660] of_register: registering tps65132_bl_driver to of_hal
[0001.666] initializing target
[0001.672] gpio_driver_register: register 'tegra_gpio_driver' driver
[0001.680] board ID = D78, board SKU = 0
[0001.684] Skipping Z3!
[0001.689] fixed regulator driver initialized
[0001.706] initializing OF layer
[0001.709] NCK carveout not present
[0001.712] Skipping dts_overrides
[0001.717] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.733] I2C Bus Init done
[0001.736] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.746] I2C Bus Init done
[0001.749] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.759] I2C Bus Init done
[0001.762] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.772] I2C Bus Init done
[0001.775] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.785] I2C Bus Init done
[0001.788] of_children_init: Ops found for compatible string maxim,max77620
[0001.798] max77620_init using irq 118
[0001.803] register 'maxim,max77620' pmic
[0001.807] gpio_driver_register: register 'max77620-gpio' driver
[0001.814] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.824] I2C Bus Init done
[0001.828] NCK carveout not present
[0001.838] Find /i2c@7000c000's alias i2c0
[0001.842] get eeprom at 1-a0, size 256, type 0
[0001.850] Find /i2c@7000c500's alias i2c2
[0001.854] get eeprom at 3-a0, size 256, type 0
[0001.859] get eeprom at 3-ae, size 256, type 0
[0001.863] pm_ids_update: Updating 1,a0, size 256, type 0
[0001.868] I2C slave not started
[0001.871] I2C write failed
[0001.874] Writing offset failed
[0001.877] eeprom_init: EEPROM read failed
[0001.881] pm_ids_update: eeprom init failed
[0001.885] pm_ids_update: Updating 3,a0, size 256, type 0
[0001.915] pm_ids_update: The pm board id is 3448-0000-200
[0001.922] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0001.930] pm_ids_update: pm id update successful
[0001.934] pm_ids_update: Updating 3,ae, size 256, type 0
[0001.964] pm_ids_update: The pm board id is 3449-0000-200
[0001.971] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0001.979] pm_ids_update: pm id update successful
[0002.009] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0002.015] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0002.023] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0002.029] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0002.038] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e6:53:41
[0002.044] Plugin Manager: Parse ODM data 0x00094000
[0002.054] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 ne
[0002.076] Find /i2c@7000c000's alias i2c0
[0002.080] get eeprom at 1-a0, size 256, type 0
[0002.089] Find /i2c@7000c500's alias i2c2
[0002.092] get eeprom at 3-a0, size 256, type 0
[0002.097] get eeprom at 3-ae, size 256, type 0
[0002.101] pm_ids_update: Updating 1,a0, size 256, type 0
[0002.107] I2C slave not started
[0002.110] I2C write failed
[0002.112] Writing offset failed
[0002.115] eeprom_init: EEPROM read failed
[0002.119] pm_ids_update: eeprom init failed
[0002.123] pm_ids_update: Updating 3,a0, size 256, type 0
[0002.153] pm_ids_update: The pm board id is 3448-0000-200
[0002.160] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0002.167] pm_ids_update: pm id update successful
[0002.171] pm_ids_update: Updating 3,ae, size 256, type 0
[0002.201] pm_ids_update: The pm board id is 3449-0000-200
[0002.208] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0002.215] pm_ids_update: pm id update successful
[0002.246] Add serial number:1422419088143 as DT property
[0002.253] Applying platform configs
[0002.260] platform-init is not present. Skipping
[0002.265] calling apps_init()
[0002.284] Found 14 GPT partitions in "sd0"
[0002.288] Proceeding to Cold Boot
[0002.291] starting app android_boot_app
[0002.295] Device state: unlocked
[0002.298] display console init
[0002.307] could not find regulator
[0002.330] hdmi cable not connected
[0002.334] is_hdmi_needed: HDMI not connected, returning falsDT entry for leds-pwm not found
e[0002.345]
[0002.346] hdmi is not connected
[0002.350] sor0 is not supported
[0002.353] display_console_init: no valid display out_type
[0002.361] subnode volume_up is not found !
[0002.365] subnode back is not found !
[0002.368] subnode volume_down is not found !
[0002.372] subnode menu is not found !
[0002.376] Gpio keyboard init success
[0002.420] found decompressor handler: lz4-legacy
[0002.434] decompressing blob (type 1)...
[0002.468] display_resolution: No display init
[0002.472] Failed to retrieve display resolution
[0002.476] Could not load/initialize BMP blob...ignoring
[0002.527] decompressor handler not found
[0002.531] load_firmware_blob: Firmware blob loaded, entries=2
[0002.537] -------> se_aes_verify_sbk_clear: 747
[0002.541] se_aes_verify_sbk_clear: Error
[0002.545] bl_battery_charging: connected to external power supply
[0002.553] xusb is supported
[0002.559] error while finding nvidia,portmap
[0003.063] xusb blob version 0 size 124416
[0003.067] firmware size 124416
[0003.072] Firmware timestamp: 0x5da88fc3, Version: 50.25 release
[0003.079] xhci0: 64 bytes context size, 32-bit DMA
[0003.119] usbus0: 5.0Gbps Super Speed USB v3.0
[0003.139] uhub0: <Nvidia XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
[0003.789] uhub0: 9 ports with 9 removable, self powered
[0004.789] failed to get HID devices
[0004.792] failed to init xhci or no usb device attached
[0004.800] display_console_ioctl: No display init
[0004.804] switch_backlight failed
[0004.811] device_query_partition_size: failed to open partition sd0:MSC !
[0004.817] MSC Partition not found
[0004.824] device_query_partition_size: failed to open partition sd0:USP !
[0004.830] USP partition read failed!
[0004.834] blob_init: blob-partition USP header read failed
[0004.839] android_boot Unable to update recovery partition
[0004.845] kfs_getpartname: name = LNX
[0004.848] Loading kernel from LNX
[0004.946] load kernel from storage
[0004.958] decompressor handler not found
[0005.015] Successfully loaded kernel and ramdisk images
[0005.022] display_resolution: No display init
[0005.026] Failed to retrieve display resolution
[0005.031] bmp blob is not loaded and initialized
[0005.035] Failed to display boot-logo
[0005.039] NCK carveout not present
[0005.042] Skipping dts_overrides
[0005.045] NCK carveout not present
[0005.055] Find /i2c@7000c000's alias i2c0
[0005.059] get eeprom at 1-a0, size 256, type 0
[0005.068] Find /i2c@7000c500's alias i2c2
[0005.072] get eeprom at 3-a0, size 256, type 0
[0005.076] get eeprom at 3-ae, size 256, type 0
[0005.081] pm_ids_update: Updating 1,a0, size 256, type 0
[0005.086] I2C slave not started
[0005.089] I2C write failed
[0005.092] Writing offset failed
[0005.095] eeprom_init: EEPROM read failed
[0005.098] pm_ids_update: eeprom init failed
[0005.103] pm_ids_update: Updating 3,a0, size 256, type 0
[0005.133] pm_ids_update: The pm board id is 3448-0000-200
[0005.139] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0005.147] pm_ids_update: pm id update successful
[0005.152] pm_ids_update: Updating 3,ae, size 256, type 0
[0005.182] pm_ids_update: The pm board id is 3449-0000-200
[0005.188] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0005.196] pm_ids_update: pm id update successful
[0005.227] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0005.233] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0005.241] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0005.247] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0005.255] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e6:53:41
[0005.262] Plugin Manager: Parse ODM data 0x00094000
[0005.272] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 ne
[0005.287] Add serial number:1422419088143 as DT property
[0005.296] "bpmp" doesn't exist, creating
[0005.301] Updated bpmp info to DTB
[0005.306] Updated initrd info to DTB
[0005.310] "proc-board" doesn't exist, creating
[0005.315] Updated board info to DTB
[0005.319] "pmu-board" doesn't exist, creating
[0005.324] Updated board info to DTB
[0005.327] "display-board" doesn't exist, creating
[0005.333] Updated board info to DTB
[0005.336] "reset" doesn't exist, creating
[0005.341] Updated reset info to DTB
[0005.344] display_console_ioctl: No display init
[0005.349] display_console_ioctl: No display init
[0005.353] display_console_ioctl: No display init
[0005.358] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 t
[0005.392] DTB cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0
[0005.405] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0
[0005.417] Updated bootarg info to DTB
[0005.421] Adding uuid 00000001644495821c00000011fd8280 to DT
[0005.427] Adding eks info 0 to DT
[0005.433] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7
[0005.438] Updated memory info to DTB
[0005.444] Updated system-lp0-disable info to DTB
[0005.453] set vdd_core voltage to 1075 mv
[0005.456] setting 'vdd-core' regulator to 1075000 micro volts
[0005.479] Found secure-pmc; disable BPMP
U-Boot 2016.07-g0536cf2a27 (Dec 09 2019 - 22:40:32 -0800)
TEGRA210
Model: NVIDIA P3450-Porg
Board: NVIDIA P3450-PORG
DRAM: 4 GiB
MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1
SF: Detected MX25U3235F with page size 256 Bytes, erase size 4 KiB, total 4 MiB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/extlinux.conf
734 bytes read in 173 ms (3.9 KiB/s)
1: primary kernel
Retrieving file: /boot/initrd
5487751 bytes read in 541 ms (9.7 MiB/s)
Retrieving file: /boot/Image
34191368 bytes read in 2934 ms (11.1 MiB/s)
## Flattened Device Tree blob at 83100000
Booting using the fdt blob at 0x83100000
reserving fdt memory region: addr=80000000 size=20000
Using Device Tree in place at 0000000083100000, end 00000000831776f0
Starting kernel ...
<hit enter to activate fiq debugger>
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.9.140-tegra (buildbrain@mobile-u64-2713) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef9
[ 0.000000] Boot CPU: AArch64 Processor [411fd071]
[ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 48,
[ 0.000000] OF: fdt: - 80000000 , 7ee00000
[ 0.000000] OF: fdt: - 100000000 , 7f200000
[ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB
[ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB
[ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB
[ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB
[ 0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout
[ 0.000000] OF: reserved mem: initialized node iram-carveout, compatible id nvidia,iram-carveout
[ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops
[ 0.000000] cma: Reserved 64 MiB at 0x00000000fac00000
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.1
[ 0.000000] percpu: Embedded 25 pages/cpu @ffffffc0fefb1000 s61592 r8192 d32616 u102400
[ 0.000000] CPU features: enabling workaround for ARM erratum 832075
[ 0.000000] Speculative Store Bypass Disable mitigation not required
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1023544
[ 0.000000] Kernel command line: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0
[ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes
[ 0.000000] log_buf_len total cpu_extra contributions: 98304 bytes
[ 0.000000] log_buf_len min size: 32768 bytes
[ 0.000000] log_buf_len: 131072 bytes
[ 0.000000] early log buf free: 29500(90%)
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] Memory: 3570416K/4159488K available (15230K kernel code, 2926K rwdata, 6620K rodata, 8576K init, 609K bss, 113936K reserved, 475136K c)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB)
[ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB)
[ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008f60000 ( 15232 KB)
[ 0.000000] .rodata : 0xffffff8008f60000 - 0xffffff80095e0000 ( 6656 KB)
[ 0.000000] .init : 0xffffff80095e0000 - 0xffffff8009e40000 ( 8576 KB)
[ 0.000000] .data : 0xffffff8009e40000 - 0xffffff800a11b808 ( 2927 KB)
[ 0.000000] .bss : 0xffffff800a11b808 - 0xffffff800a1b3dbc ( 610 KB)
[ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB)
[ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB)
[ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum)
[ 0.000000] 0xffffffbf00000000 - 0xffffffbf03fc8000 ( 63 MB actual)
[ 0.000000] memory : 0xffffffc000000000 - 0xffffffc0ff200000 ( 4082 MB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 64.
[ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[ 0.000000] NR_IRQS:64 nr_irqs:64 0
[ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller
[ 0.000000] t210 clock and reset probe
[ 0.000000] tegra-pmc: get_secure_pmc_setting: done secure_pmc=1
[ 0.000000] clk_cbus_recalc_rate: no gbus parent
[ 0.000000] clk_cbus_recalc_rate: no gbus parent
[ 0.000000] clk_cbus_recalc_rate: no gbus parent
[ 0.000000] clk_cbus_recalc_rate: no gbus parent
[ 0.000000] clk_cbus_recalc_rate: no gbus parent
[ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[ 0.000006] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[ 0.001665] Console: colour dummy device 80x25
[ 0.002501] console [tty0] enabled
[ 0.002527] kmemleak: Kernel memory leak detector disabled
[ 0.002559] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800)
[ 0.002589] pid_max: default: 32768 minimum: 301
[ 0.003047] Security Framework initialized
[ 0.003279] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.003300] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.004495] ftrace: allocating 47001 entries in 184 pages
[ 0.176078] ASID allocator initialised with 65536 entries
[ 0.215844] tegra-id: chipid=22117.
[ 0.215887] tegra-id: opt_subrevision=0.
[ 0.215917] Tegra Speedo/IDDQ fuse revision 4
[ 0.215932] Tegra: CPU Speedo ID 9, SoC Speedo ID 0, GPU Speedo ID 2
[ 0.215949] Tegra: CPU Process ID 0, SoC Process ID 1, GPU Process ID 0
[ 0.215965] Tegra: CPU Speedo Value 2084, SoC Speedo Value 1976, GPU Speedo Value 2075
[ 0.215986] Tegra: CPU IDDQ Value 1872, SoC IDDQ Value 1980, GPU IDDQ Value 2430
[ 0.216022] Tegra Revision: A02 SKU: 0x8f CPU Process: 0 SoC Process: 1
[ 0.216048] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/ps
[ 0.216081] DTB Build time: Dec 9 2019 22:51:54
[ 0.265024] CPU1: Booted secondary processor [411fd071]
[ 0.296967] CPU2: Booted secondary processor [411fd071]
[ 0.328941] CPU3: Booted secondary processor [411fd071]
[ 0.329027] Brought up 4 CPUs
[ 0.329092] SMP: Total of 4 processors activated.
[ 0.329110] CPU features: detected feature: 32-bit EL0 Support
[ 0.329380] CPU: All CPU(s) started at EL2
[ 0.329411] alternatives: patching kernel code
[ 0.337443] devtmpfs: initialized
[ 0.374790] Initilizing CustomIPI irq domain
[ 0.375218] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.375265] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.385732] pinctrl core: initialized pinctrl subsystem
[ 0.386414] OS set in device tree is not L4T.
[ 0.386813] regulator-dummy: no parameters
[ 0.387115] Initializing plugin-manager
[ 0.387245] Plugin module not found
[ 0.387491] node /plugin-manager/fragement@0 match with board >=3448-0000-100
[ 0.388054] node /plugin-manager/fragment@1 match with board >=3448-0000-101
[ 0.388947] node /plugin-manager/fragment@5 match with board 3449-0000-200
[ 0.389464] node /plugin-manager/fragement@6 match with odm-data enable-tegra-wdt
[ 0.389914] node /plugin-manager/fragement@8 match with odm-data enable-tegra-wdt
[ 0.390329] node /plugin-manager/fragement@9 match with board <3448-0000-300
[ 0.395085] NET: Registered protocol family 16
[ 0.396382] pstore: using zlib compression
[ 0.397085] console [pstore-1] enabled
[ 0.397103] pstore: Registered ramoops as persistent store backend
[ 0.397121] ramoops: attached 0x200000@0xb0000000, ecc: 0/0
[ 0.413044] cpuidle: using governor menu
[ 0.417255] tegra_smmu 70019000.iommu: Loaded Tegra IOMMU driver
[ 0.418876] vdso: 2 pages (1 code @ ffffff8008f67000, 1 data @ ffffff8009e44000)
[ 0.418921] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.421495] atomic_pool_init():622: DMA: preallocated 1024 KiB pool for atomic allocations
[ 0.424083] tegra_powergate_init: DONE
[ 0.424120] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/ps
[ 0.424157] DTB Build time: Dec 9 2019 22:51:54
[ 0.425942] Tegra reboot handler registered.
[ 0.430420] iommu: Adding device tegra-carveouts to group 0
[ 0.430590] platform tegra-carveouts: domain=ffffffc0f9bbe318 allocates as[0]=ffffffc0f94180a8
[ 0.430965] iommu: Adding device smmu_test to group 1
[ 0.431033] platform smmu_test: domain=ffffffc0f9bbe558 allocates as[0]=ffffffc0f9418110
[ 0.431862] mc: mapped MMIO address: 0xffffff800802e000 -> 0x70019000
[ 0.431943] mc: mapped MMIO address: 0xffffff8008065000 -> 0x7001c000
[ 0.432012] mc: mapped MMIO address: 0xffffff8008079000 -> 0x7001d000
[ 0.432034] nv-tegra-mc 70019000.mc: No mssnvlink node
[ 0.432070] mc-err: mcerr ops are set to t21x
[ 0.441873] iommu: Adding device 70090000.xusb to group 2
[ 0.442193] iommu: Adding device 70006000.serial to group 3
[ 0.442291] platform 70006000.serial: domain=ffffffc0f94b1618 allocates as[0]=ffffffc0f9418178
[ 0.442738] iommu: Adding device 70006040.serial to group 4
[ 0.443028] iommu: Adding device 70006200.serial to group 5
[ 0.443276] iommu: Adding device sound to group 6
[ 0.443341] platform sound: domain=ffffffc0f94b1b58 allocates as[0]=ffffffc0f94181e0
[ 0.443900] iommu: Adding device 7000d400.spi to group 7
[ 0.444175] iommu: Adding device 7000d600.spi to group 8
[ 0.444472] iommu: Adding device 70410000.spi to group 9
[ 0.444792] iommu: Adding device 50000000.host1x to group 10
[ 0.445143] iommu: Adding device 54080000.vi to group 11
[ 0.445557] iommu: Adding device 54600000.isp to group 12
[ 0.445837] iommu: Adding device 54680000.isp to group 13
[ 0.446156] iommu: Adding device tegradc.0 to group 14
[ 0.446223] platform tegradc.0: domain=ffffffc0f94bfa98 allocates as[0]=ffffffc0f9418248
[ 0.446754] platform tegradc.0: IOVA linear map 0x00000000d7000000(19000000)
[ 0.447091] iommu: Adding device tegradc.1 to group 15
[ 0.447158] platform tegradc.1: domain=ffffffc0f94bfcd8 allocates as[0]=ffffffc0f94182b0
[ 0.447681] platform tegradc.1: IOVA linear map 0x00000000d7000000(19000000)
[ 0.447940] iommu: Adding device 54340000.vic to group 16
[ 0.448165] iommu: Adding device 544c0000.nvenc to group 17
[ 0.448381] iommu: Adding device 54500000.tsec to group 18
[ 0.448600] iommu: Adding device 54100000.tsecb to group 19
[ 0.448811] iommu: Adding device 54480000.nvdec to group 20
[ 0.449084] iommu: Adding device 54380000.nvjpg to group 21
[ 0.450185] iommu: Adding device 546c0000.i2c to group 22
[ 0.450543] iommu: Adding device 57000000.gpu to group 23
[ 0.450615] platform 57000000.gpu: domain=ffffffc0f94cacd8 allocates as[0]=ffffffc0f9418318
[ 0.450670] platform 57000000.gpu: domain=ffffffc0f94cacd8 allocates as[1]=ffffffc0f9418380
[ 0.450729] platform 57000000.gpu: domain=ffffffc0f94cacd8 allocates as[2]=ffffffc0f94183e8
[ 0.450784] platform 57000000.gpu: domain=ffffffc0f94cacd8 allocates as[3]=ffffffc0f9418450
[ 0.451706] tegra-pmc 7000e400.pmc: i2c-thermtrip node not found, emergency thermal reset disabled.
[ 0.451747] tegra-pmc 7000e400.pmc: scratch reg offset dts data not present
[ 0.451774] tegra-pmc: ### PMC reset source: TEGRA_SOFTWARE_RESET
[ 0.451795] tegra-pmc: ### PMC reset level: TEGRA_RESET_LEVEL_WARM
[ 0.451813] tegra-pmc: ### PMC reset status reg: 0x3
[ 0.501147] padctrl padctrl.0: Pad control driver tegra-pmc-padctrl registered
[ 0.501185] tegra-pmc: Clear bootloader IO dpd settings
[ 0.501219] tegra-pmc 7000e400.pmc: IO padctrl driver initialized
[ 0.501301] tegra-pmc 7000e400.pmc: PMC: Successfully configure bootrom reset commands
[ 0.501618] iommu: Adding device 70012000.se to group 24
[ 0.502415] iommu: Adding device 7000c000.i2c to group 25
[ 0.502682] iommu: Adding device 7000c400.i2c to group 26
[ 0.502948] iommu: Adding device 7000c500.i2c to group 27
[ 0.503211] iommu: Adding device 7000c700.i2c to group 28
[ 0.503509] iommu: Adding device 7000d000.i2c to group 29
[ 0.503771] iommu: Adding device 7000d100.i2c to group 30
[ 0.504074] iommu: Adding device sdhci-tegra.0 to group 31
[ 0.504140] platform sdhci-tegra.0: domain=ffffffc0f9562e58 allocates as[0]=ffffffc0f94184b8
[ 0.504989] iommu: Adding device 700d0000.xudc to group 32
[ 0.508367] vdd-ac-bat: 5000 mV
[ 0.508748] vdd-5v0-sys: 5000 mV
[ 0.509711] vdd-5v0-hdmi: supplied by vdd-5v0-sys
[ 0.509798] vdd-5v0-hdmi: 5000 mV
[ 0.510208] vdd-1v8-sys: 1800 mV
[ 0.510608] vdd-fan: supplied by vdd-5v0-sys
[ 0.510660] vdd-fan: 5000 mV
[ 0.511052] vdd-usb-vbus: supplied by vdd-5v0-sys
[ 0.511120] vdd-usb-vbus: 5000 mV
[ 0.511678] vdd-usb-vbus2: 5000 mV
[ 0.542101] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.544506] gpio gpiochip0: gpio-line-names specifies 240 line names but there are 256 lines on the chip
[ 0.545636] GPIO line 151 (camera-control-output-low) hogged as output/low
[ 0.545674] GPIO line 152 (camera-control-output-low) hogged as output/low
[ 0.546060] gpiochip_setup_dev: registered GPIOs 0 to 255 on device: gpiochip0 (tegra-gpio)
[ 0.553619] eventlib_kernel: keventlib is initialized, test id: 0
[ 0.553999] SCSI subsystem initialized
[ 0.554517] usbcore: registered new interface driver usbfs
[ 0.554591] usbcore: registered new interface driver hub
[ 0.554688] usbcore: registered new device driver usb
[ 0.558816] max77620 4-003c: PMIC Version OTP:0x35 and ES:0x8
[ 0.565148] vdd-core: 600 <--> 1162 mV at 1075 mV
[ 0.565841] random: fast init done
[ 0.566195] vdd-ddr-1v1: Bringing 1125000uV into 1150000-1150000uV
[ 0.569035] vdd-ddr-1v1: 1150 mV
[ 0.572231] vdd-pre-reg-1v35: 1350 mV
[ 0.576229] vdd-1v8: 1800 mV
[ 0.580229] avdd-sys-1v2: 1200 mV
[ 0.584230] vdd-pex-1v0: 1050 mV
[ 0.584864] vddio-sdmmc-ap: 1800 <--> 3300 mV at 3300 mV
[ 0.585423] max77620-ldo3: at 3100 mV
[ 0.588232] vdd-rtc: 850 <--> 1100 mV at 1000 mV
[ 0.588828] max77620-ldo5: at 3100 mV
[ 0.589389] max77620-ldo6: at 2800 mV
[ 0.592234] avdd-1v05-pll: 1050 mV
[ 0.596227] avdd-io-hdmi-dp: 1050 mV
[ 0.598871] GPIO line 505 (spmic-default-output-high) hogged as output/high
[ 0.599165] gpiochip_setup_dev: registered GPIOs 504 to 511 on device: gpiochip1 (max77620-gpio)
[ 0.599475] max77620 4-003c: max77620 probe successful
[ 0.602175] media: Linux media interface: v0.10
[ 0.602261] Linux video capture interface: v2.00
[ 0.603181] pps_core: LinuxPPS API ver. 1 registered
[ 0.603206] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.603248] PTP clock support registered
[ 0.606899] tegra_fiq_debugger_init: found FIQ source (IRQ 98)
[ 0.613297] tegra210-emc 7001b000.external-memory-controller: validated EMC DFS table
[ 0.614150] Advanced Linux Sound Architecture Driver Initialized.
[ 0.614807] Bluetooth: Core ver 2.22
[ 0.614878] NET: Registered protocol family 31
[ 0.614897] Bluetooth: HCI device and connection manager initialized
[ 0.614924] Bluetooth: HCI socket layer initialized
[ 0.614946] Bluetooth: L2CAP socket layer initialized
[ 0.614985] Bluetooth: SCO socket layer initialized
[ 0.616743] tegra210_dvfs: no clock found for sdmmc2_ddr
[ 0.616781] tegra210_dvfs: no clock found for sdmmc4_ddr
[ 0.616842] tegra210_dvfs: no clock found for sdmmc1_ddr
[ 0.616870] tegra210_dvfs: no clock found for sdmmc3_ddr
[ 0.620039] tegra_dvfs: Unable to get vdd-cpu rail for step info, defering probe
[ 0.621361] vdd-3v3-sys: supplied by vdd-5v0-sys
[ 0.621450] vdd-3v3-sys: 3300 mV
[ 0.621774] vdd-1v8-sys: supplied by vdd-3v3-sys
[ 0.625113] vdd-usb-vbus2: supplied by vdd-3v3-sys
[ 0.625593] vdd-3v3-sd: supplied by vdd-3v3-sys
[ 0.625646] vdd-3v3-sd: 3300 mV
[ 0.626620] avdd-io-edp-1v05: supplied by avdd-1v05-pll
[ 0.626701] avdd-io-edp-1v05: 1050 mV
[ 0.627199] vdd-usb-hub-en: supplied by vdd-1v8-sys
[ 0.627252] vdd-usb-hub-en: 5000 mV
[ 0.628671] camchar: rtcpu character device driver loaded
[ 0.629408] extcon-gpio-states extcon:extcon@1: Cable state:1, cable id:1
[ 0.630756] clocksource: Switched to clocksource arch_sys_counter
[ 0.670089] VFS: Disk quotas dquot_6.6.0
[ 0.670255] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.670824] nvmap_heap_init: nvmap_heap_init: created heap block cache
[ 0.671241] dma_declare_coherent_resizable_cma_memory:324: resizable heap=vpr, base=0x00000000d7000000, size=0x19000000
[ 0.671290] dma-vpr: heap size is not multiple of cma_chunk_size heap_info->num_chunks (13) rem_chunk_size(0x1000000)
[ 0.671563] cma: enabled page replacement for spfn=d7000, epfn=f0000
[ 0.671592] dma_declare_coherent_resizable_cma_memory:373: resizable cma heap=vpr create successful
[ 0.671620] tegra-carveouts tegra-carveouts: assigned reserved memory node vpr-carveout
[ 0.671675] tegra-carveouts tegra-carveouts: iram :dma coherent mem declare 0x0000000040001000,258048
[ 0.671702] tegra-carveouts tegra-carveouts: assigned reserved memory node iram-carveout
[ 0.671735] nvmap: nvmap_select_cache_ops() nvmap cache ops set to set/ways
[ 0.671760] nvmap_page_pool_init: Total RAM pages: 1011388
[ 0.671778] nvmap_page_pool_init: nvmap page pool size: 126423 pages (493 MB)
[ 0.671905] nvmap_background_zero_thread: PP zeroing thread starting.
[ 0.672261] misc nvmap: created heap iram base 0x0000000040001000 size (252KiB)
[ 0.673069] misc nvmap: created heap vpr base 0x00000000d7000000 size (409600KiB)
[ 0.681483] thermal thermal_zone0: Registering thermal zone thermal_zone0 for type AO-therm
[ 0.681949] thermal thermal_zone1: Registering thermal zone thermal_zone1 for type CPU-therm
[ 0.682219] thermal thermal_zone2: Registering thermal zone thermal_zone2 for type GPU-therm
[ 0.682443] thermal thermal_zone3: Registering thermal zone thermal_zone3 for type PLL-therm
[ 0.682642] thermal thermal_zone4: Registering thermal zone thermal_zone4 for type PMIC-Die
[ 0.682965] pre_t19x_iso_plat_init(): iso emc max clk=1600000KHz
[ 0.682990] pre_t19x_iso_plat_init(): max_iso_bw=11520000KB
[ 0.683446] NET: Registered protocol family 2
[ 0.684526] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.684767] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[ 0.685277] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.685446] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.685544] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.685979] NET: Registered protocol family 1
[ 0.686711] RPC: Registered named UNIX socket transport module.
[ 0.686772] RPC: Registered udp transport module.
[ 0.686790] RPC: Registered tcp transport module.
[ 0.686807] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.687073] Trying to unpack rootfs image as initramfs...
[ 0.919065] Freeing initrd memory: 5356K
[ 0.928949] host1x 50000000.host1x: initialized
[ 0.930794] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[ 0.934004] audit: initializing netlink subsys (disabled)
[ 0.934095] audit: type=2000 audit(0.783:1): initialized
[ 0.934904] workingset: timestamp_bits=46 max_order=20 bucket_order=0
[ 0.944929] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.946470] ntfs: driver 2.1.32 [Flags: R/W].
[ 0.947315] 9p: Installing v9fs 9p2000 file system support
[ 0.950514] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 240)
[ 0.950666] io scheduler noop registered
[ 0.951009] io scheduler cfq registered (default)
[ 0.953633] gic 702f9000.agic: GIC IRQ controller registered
[ 0.957013] iommu: Adding device 702ef000.adsp to group 33
[ 0.965991] iommu: Adding device aconnect@702c0000:adsp_audio to group 34
[ 0.966157] tegra-aconnect aconnect@702c0000: Tegra ACONNECT bus registered
[ 0.966806] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_SKU_CALIB_0 = 0x8229413
[ 0.966839] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_USB_CALIB_EXT_0 = 0x4
[ 0.968461] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.0, lane = usb2-0, function = xusb
[ 0.968603] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.1, lane = usb2-1, function = xusb
[ 0.968714] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.2, lane = usb2-2, function = xusb
[ 0.968923] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.3, lane = pcie-0, function = pcie-x1
[ 0.969029] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.4, lane = pcie-1, function = pcie-x4
[ 0.969140] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.5, lane = pcie-2, function = pcie-x4
[ 0.969251] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.6, lane = pcie-3, function = pcie-x4
[ 0.969370] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.7, lane = pcie-4, function = pcie-x4
[ 0.969475] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.8, lane = pcie-5, function = xusb
[ 0.969587] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.9, lane = pcie-6, function = xusb
[ 0.975656] tegra-pwm 7000a000.pwm: PWM clk cannot sleep in ops
[ 0.977363] tegra-dfll-pwm 70110000.pwm: DFLL pwm-rate: 12800000
[ 0.979312] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration
[ 0.980600] tegra-pcie 1003000.pcie: PCIE: Enable power rails
[ 0.980977] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes
[ 0.982190] tegra_camera_platform tegra-camera-platform: tegra_camera_probe:camera_platform_driver probe
[ 0.982427] misc tegra_camera_ctrl: tegra_camera_isomgr_register isp_iso_bw=1500000, vi_iso_bw=750000, max_bw=1500000
[ 0.982676] Adding domain tsec-pd to PM domain host1x-pd
[ 0.984976] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes
[ 0.985921] tsec 54500000.tsec: initialized
[ 0.987512] tsec 54100000.tsecb: initialized
[ 0.988211] Adding domain nvdec-pd to PM domain host1x-pd
[ 0.991578] nvdec 54480000.nvdec: initialized
[ 0.992620] Adding domain vic03-pd to PM domain host1x-pd
[ 0.992830] Adding domain msenc-pd to PM domain host1x-pd
[ 0.993004] Adding domain nvjpg-pd to PM domain host1x-pd
[ 0.997015] falcon 54340000.vic: initialized
[ 0.998273] falcon 544c0000.nvenc: initialized
[ 0.999626] falcon 54380000.nvjpg: initialized
[ 1.003846] tegra_cec 70015000.tegra_cec: dt=1 start=0x70015000 end=0x70015FFF irq=97
[ 1.003925] tegra_cec 70015000.tegra_cec: Enable clock result: 0.
[ 1.003947] tegradc tegradc.0: disp0 connected to head0->/host1x/sor1
[ 1.003972] tegra_cec 70015000.tegra_cec: tegra_cec_init started
[ 1.004088] display board info: id 0x0, fab 0x0
[ 1.004158] generic_infoframe_type: 0x87
[ 1.004268] tegra_cec 70015000.tegra_cec: cec_add_sysfs ret=0
[ 1.004290] tegra_cec 70015000.tegra_cec: probed
[ 1.004307] tegradc tegradc.0: DT parsed successfully
[ 1.004371] tegradc tegradc.0: Display dc.ffffff800ab40000 registered with id=0
[ 1.011892] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels
[ 1.012415] tegradc tegradc.0: probed
[ 1.013114] Console: switching to colour frame buffer device 80x30
[ 1.013165] tegradc tegradc.0: fb registered
[ 1.014640] tegradc tegradc.1: disp1 connected to head1->/host1x/sor
[ 1.014799] tegradc tegradc.1: No lt-data, using default setting
[ 1.014859] tegradc tegradc.1: No hpd-gpio in DT
[ 1.014913] tegradc tegradc.1: DT parsed successfully
[ 1.014979] tegradc tegradc.1: Display dc.ffffff800acc0000 registered with id=1
[ 1.016442] tegradc tegradc.1: dpd enable lookup fail:-19
[ 1.018019] tegra-adma 702e2000.adma: Tegra210 ADMA driver registered 22 channels
[ 1.018888] tegra-fuse-burn 7000f800.efuse:efuse-burn: Fuse burn driver initialized
[ 1.019263] kfuse 7000fc00.kfuse: initialized
[ 1.522445] Host read timeout at address 545c00c4
[ 1.522672] tegra-pmc-iopower pmc-iopower: Regulator supply iopower-dbg-supply not available
[ 1.523622] tegra-pmc-iopower pmc-iopower: NO_IOPOWER setting 0x0
[ 1.523701] tegradc tegradc.1: probed
[ 1.524069] tegradc tegradc.1: fb registered
[ 1.524891] tegra-dfll-pwm 70110000.pwm: DFLL_PWM regulator is available now
[ 1.524923] vdd-cpu: 708 <--> 1322 mV at 708 mV
[ 1.525332] pwm-regulator pwm_regulators:pwm-regulator@0: PWM regulator registration passed
[ 1.526632] vdd-gpu: applied init 1000000uV constraint
[ 1.526653] vdd-gpu: 708 <--> 1323 mV at 997 mV
[ 1.527058] pwm-regulator pwm_regulators:pwm-regulator@1: PWM regulator registration passed
[ 1.527274] hpd: state 7 (Takeover from bootloader), hpd 0, pending_hpd_evt 1
[ 1.527297] hpd: switching from state 7 (Takeover from bootloader) to state 0 (Reset)
[ 1.527319] hpd: state 0 (Reset), hpd 0, pending_hpd_evt 0
[ 1.527345] tegradc tegradc.1: blank - powerdown
[ 1.527376] extcon-disp-state extcon:disp-state: cable 44 state 0 already set.
[ 1.527393] Extcon DP: HPD disabled
[ 1.527405] hpd: hpd_switch 0
[ 1.527418] hpd: switching from state 0 (Reset) to state 1 (Check Plug)
[ 1.527441] hpd: state 1 (Check Plug), hpd 0, pending_hpd_evt 0
[ 1.527458] hpd: switching from state 1 (Check Plug) to state 3 (Disabled)
[ 1.530548] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.530678] No Device Node present for smmu client: serial8250 !!
[ 1.530702] platform serial8250: No iommus property found in DT node, got swgids from fixup(101004000)
[ 1.530967] iommu: Adding device serial8250 to group 35
[ 1.533271] console [ttyS0] disabled
[ 1.533407] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 63, base_baud = 25500000) is a Tegra
[ 1.910556] tegra-pcie 1003000.pcie: link 0 down, retrying
[ 2.038773] tegra_cec 70015000.tegra_cec: Can't find physical addresse.
[ 2.038777] tegra_cec 70015000.tegra_cec: tegra_cec_init Done.
[ 2.314367] tegra-pcie 1003000.pcie: link 0 down, retrying
[ 2.718676] tegra-pcie 1003000.pcie: link 0 down, retrying
[ 2.720694] tegra-pcie 1003000.pcie: link 0 down, ignoring
[ 2.826897] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00
[ 2.826908] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 2.826913] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff]
[ 2.826926] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref]
[ 2.826932] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 2.827315] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 2.838911] pci 0000:00:02.0: BAR 14: assigned [mem 0x13000000-0x130fffff]
[ 2.838917] pci 0000:00:02.0: BAR 13: assigned [io 0x1000-0x1fff]
[ 2.838926] pci 0000:01:00.0: BAR 4: assigned [mem 0x13000000-0x13003fff 64bit]
[ 2.838946] pci 0000:01:00.0: BAR 2: assigned [mem 0x13004000-0x13004fff 64bit]
[ 2.838965] pci 0000:01:00.0: BAR 0: assigned [io 0x1000-0x10ff]
[ 2.838977] pci 0000:00:02.0: PCI bridge to [bus 01]
[ 2.838983] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff]
[ 2.838990] pci 0000:00:02.0: bridge window [mem 0x13000000-0x130fffff]
[ 2.839398] pcieport 0000:00:02.0: Signaling PME through PCIe PME interrupt
[ 2.839402] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
[ 4.057452] console [ttyS0] enabled
[ 4.062131] 70006040.serial: ttyTHS1 at MMIO 0x70006040 (irq = 64, base_baud = 0) is a TEGRA_UART
[ 4.071393] serial-tegra 70006200.serial: RX in PIO mode
[ 4.076825] 70006200.serial: ttyTHS2 at MMIO 0x70006200 (irq = 65, base_baud = 0) is a TEGRA_UART
[ 4.086668] [drm] Initialized
[ 4.099597] brd: module loaded
[ 4.108221] loop: module loaded
[ 4.111506] tegra_profiler: version: 1.139, samples/io: 47/27
[ 4.117456] tegra_profiler: auth: init
[ 4.122530] THERMAL EST: found 2 subdevs
[ 4.126538] THERMAL EST num_resources: 0
[ 4.130482] [THERMAL EST subdev 0]
[ 4.133900] [THERMAL EST subdev 1]
[ 4.137775] thermal thermal_zone5: Registering thermal zone thermal_zone5 for type thermal-fan-est
[ 4.146751] THERMAL EST: thz register success.
[ 4.151345] THERMAL EST: end of probe, return err: 0
[ 4.157519] hisi_sas: driver version v1.6
[ 4.165826] tegra-qspi 70410000.spi: Prod settings list not found
[ 4.173158] qspi_mtd spi32766.0: MX25U3235F (4096 Kbytes)
[ 4.178586] qspi_mtd spi32766.0: mtd .name = spi32766.0, .size = 0x400000 (4MiB) .erasesize = 0x00001000 (4KiB) .numeraseregions = 0
[ 4.193596] libphy: Fixed MDIO Bus: probed
[ 4.198460] tun: Universal TUN/TAP device driver, 1.6
[ 4.203540] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 4.210678] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[ 4.216534] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 4.222526] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
[ 4.229501] igb: Copyright (c) 2007-2014 Intel Corporation.
[ 4.235140] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k
[ 4.242979] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
[ 4.248951] Intel(R) 10GbE PCI Express Linux Network Driver - version 4.6.4
[ 4.255924] Copyright(c) 1999 - 2017 Intel Corporation.
[ 4.261995] r8168 0000:01:00.0: enabling device (0000 -> 0003)
[ 4.267886] r8168 Gigabit Ethernet driver 8.045.08-NAPI loaded
[ 4.287893] r8168 0000:01:00.0 (unnamed net_device) (uninitialized): Invalid ethernet address 00:00:00:00:00:00, trying device tree node
[ 4.300328] r8168 0000:01:00.0 (unnamed net_device) (uninitialized): Found valid ethernet address 00:04:4b:e6:53:41 from device tree
[ 4.312780] r8168: This product is covered by one or more of the following patents: US6,570,884, US6,115,776, and US6,327,625.
[ 4.324235] r8168 Copyright (C) 2017 Realtek NIC software team <nicfae@realtek.com>
[ 4.324235] This program comes with ABSOLUTELY NO WARRANTY; for details, please see <http://www.gnu.org/licenses/>.
[ 4.324235] This is free software, and you are welcome to redistribute it under certain conditions; see <http://www.gnu.org/licenses/>.
[ 4.355621] PPP generic driver version 2.4.2
[ 4.360105] PPP BSD Compression module registered
[ 4.364825] PPP Deflate Compression module registered
[ 4.369923] PPP MPPE Compression module registered
[ 4.374724] NET: Registered protocol family 24
[ 4.379248] usbcore: registered new interface driver r8152
[ 4.384794] usbcore: registered new interface driver asix
[ 4.390263] usbcore: registered new interface driver ax88179_178a
[ 4.396400] usbcore: registered new interface driver cdc_ether
[ 4.402280] usbcore: registered new interface driver net1080
[ 4.407992] usbcore: registered new interface driver cdc_subset
[ 4.413960] usbcore: registered new interface driver zaurus
[ 4.419600] usbcore: registered new interface driver cdc_ncm
[ 4.425432] VFIO - User Level meta-driver version: 0.3
[ 4.431812] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.438378] ehci-pci: EHCI PCI platform driver
[ 4.442885] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.449079] ohci-pci: OHCI PCI platform driver
[ 4.453577] ohci-platform: OHCI generic platform driver
[ 4.461326] tegra-xusb 70090000.xusb: USB2 port 0 has OTG_CAP
[ 4.467762] tegra-xusb-padctl 7009f000.xusb_padctl: enabled OTG on UTMI pad 0
[ 4.476115] tegra-xusb 70090000.xusb: extcon 0: ffffffc0f942b800 id
[ 4.484623] usbcore: registered new interface driver uas
[ 4.489993] tegra-xusb 70090000.xusb: Firmware timestamp: 2019-10-17 15:58:59 UTC, Version: 50.25 release
[ 4.490053] tegra-xusb 70090000.xusb: xHCI Host Controller
[ 4.490078] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 1
[ 4.490884] tegra-xusb 70090000.xusb: hcc params 0x0184f525 hci version 0x100 quirks 0x00050010
[ 4.490950] tegra-xusb 70090000.xusb: irq 61, io mem 0x70090000
[ 4.491220] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 4.491225] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.491229] usb usb1: Product: xHCI Host Controller
[ 4.491233] usb usb1: Manufacturer: Linux 4.9.140-tegra xhci-hcd
[ 4.491237] usb usb1: SerialNumber: 70090000.xusb
[ 4.491832] hub 1-0:1.0: USB hub found
[ 4.491875] hub 1-0:1.0: 5 ports detected
[ 4.492404] tegra-xusb 70090000.xusb: xHCI Host Controller
[ 4.492414] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 2
[ 4.492486] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 4.492580] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 4.492584] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.492588] usb usb2: Product: xHCI Host Controller
[ 4.492592] usb usb2: Manufacturer: Linux 4.9.140-tegra xhci-hcd
[ 4.492595] usb usb2: SerialNumber: 70090000.xusb
[ 4.493008] hub 2-0:1.0: USB hub found
[ 4.493084] hub 2-0:1.0: 4 ports detected
[ 4.594819] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 1
[ 4.630883] usbcore: registered new interface driver usb-storage
[ 4.637016] usbcore: registered new interface driver usbserial
[ 4.646206] tegra-xudc-new 700d0000.xudc: device count: 1
[ 4.652894] tegra-xudc-new 700d0000.xudc: USB charger detection disabled
[ 4.659638] tegra-xudc-new 700d0000.xudc: vbus state: 1
[ 4.664887] tegra-xudc-new 700d0000.xudc: device mode on: 0
[ 4.670493] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 0
[ 4.677208] tegra-xudc-new 700d0000.xudc: active: 0 => 1
[ 4.683199] mousedev: PS/2 mouse device common for all mice
[ 4.688892] usbcore: registered new interface driver xpad
[ 4.818769] usb 1-2: new high-speed USB device number 2 using tegra-xusb
[ 4.825361] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0
[ 4.827790] rtc rtc1: alarm rtc device
[ 4.827813] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1
[ 4.827841] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock
[ 4.828344] i2c /dev entries driver
[ 4.830216] imx219 6-0010: tegracam sensor driver:imx219_v2.0.6
[ 4.853542] tegra-vii2c 546c0000.i2c: no acknowledge from address 0x10
[ 4.853614] imx219 6-0010: imx219_board_setup: error during i2c read probe (-121)
[ 4.853643] imx219 6-0010: board setup failed
[ 4.853734] imx219: probe of 6-0010 failed with error -121
[ 4.854922] max77620-power max77620-power: Event recorder REG_NVERC : 0x0
[ 4.857625] tegra_soctherm 700e2000.soctherm: pllx_offset tz:0 max:14, min:2
[ 4.857630] tegra_soctherm 700e2000.soctherm: pllx_offset tz:2 max:8, min:4
[ 4.858081] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[ 4.858097] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when cpu reaches 102500 mC
[ 4.858105] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when cpu reaches 100500 mC
[ 4.858238] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[ 4.858248] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when gpu reaches 103000 mC
[ 4.858254] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when gpu reaches 101000 mC
[ 4.858400] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[ 4.858410] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when pll reaches 127000 mC
[ 4.858415] tegra_soctherm 700e2000.soctherm: throttrip: pll: missing hot temperature
[ 4.858590] tegra_soctherm 700e2000.soctherm: failed to register sensor: -19
[ 4.859404] tegra_aotag tegra-aotag: Registering sensor 0
[ 4.859458] tegra_aotag tegra-aotag: Invalid temp readout
[ 4.859484] tegra_aotag tegra-aotag: Invalid temp readout
[ 4.859500] tegra_aotag tegra-aotag: Bound to TZ : ID 0
[ 4.859509] tegra_aotag tegra-aotag: Probe done [SUCCESS]:0
[ 4.860368] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[ 4.860387] tegra_dfll_action dfll-cdev-cap: Tegra DFLL 'cap cooling device' registered
[ 4.860564] tegra_aotag tegra-aotag: Invalid temp readout
[ 4.860596] tegra_dfll_action dfll-cdev-floor: Tegra DFLL 'floor cooling device' registered
[ 4.860971] parse_throttle_dt_data: Num cap clks = 6
[ 4.860978] parse_throttle_dt_data: clk=cclk_g type=2
[ 4.860991] parse_throttle_dt_data: clk=gpu type=4
[ 4.861015] parse_throttle_dt_data: clk=cap.throttle.c2bus type=0
[ 4.861034] parse_throttle_dt_data: clk=cap.throttle.c3bus type=0
[ 4.861054] parse_throttle_dt_data: clk=cap.throttle.sclk type=0
[ 4.861058] parse_throttle_dt_data: clk=emc type=3
[ 4.861620] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[ 4.861731] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[ 4.861892] tegra_throttle_probe: probe successful. #cdevs=4
[ 4.862777] FAN dev name: pwm-fan
[ 4.862872] FAN:gpio request success.
[ 4.862944] pwm_fan_driver pwm-fan: cap state:7, cap pwm:255
[ 4.863262] pwm_fan_driver pwm-fan: got pwm for fan. polarity is normal
[ 4.863442] pwm_fan_driver pwm-fan: fan tach request irq success
[ 4.863450] pwm_fan_driver pwm-fan: tach period: 1000
[ 4.863548] pwm_fan_driver pwm-fan: index 0: pwm=0, rpm=0, rru=40, rrd=40, state:2
[ 4.863553] pwm_fan_driver pwm-fan: index 1: pwm=80, rpm=1000, rru=2, rrd=2, state:2
[ 4.863557] pwm_fan_driver pwm-fan: index 2: pwm=120, rpm=2000, rru=1, rrd=1, state:2
[ 4.863561] pwm_fan_driver pwm-fan: index 3: pwm=160, rpm=3000, rru=1, rrd=1, state:2
[ 4.863565] pwm_fan_driver pwm-fan: index 4: pwm=255, rpm=4000, rru=1, rrd=1, state:3
[ 4.863568] pwm_fan_driver pwm-fan: index 5: pwm=255, rpm=5000, rru=1, rrd=1, state:3
[ 4.863572] pwm_fan_driver pwm-fan: index 6: pwm=255, rpm=6000, rru=1, rrd=1, state:3
[ 4.863576] pwm_fan_driver pwm-fan: index 7: pwm=255, rpm=7000, rru=1, rrd=1, state:4
[ 4.863579] pwm_fan_driver pwm-fan: index 8: pwm=255, rpm=10000, rru=1, rrd=1, state:4
[ 4.863583] pwm_fan_driver pwm-fan: index 9: pwm=255, rpm=11000, rru=1, rrd=1, state:4
[ 4.864312] tegra-wdt 60005100.watchdog: Tegra WDT enabled on probe. Timeout = 120 seconds.
[ 4.864658] tegra-wdt 60005100.watchdog: initialized (timeout = 120 sec, nowayout = 1)
[ 4.865702] device-mapper: uevent: version 1.0.3
[ 4.866211] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com
[ 4.871618] tegra210-cpufreq cpufreq: probe()...completed
[ 4.872491] sdhci: Secure Digital Host Controller Interface driver
[ 4.872493] sdhci: Copyright(c) Pierre Ossman
[ 4.872494] sdhci-pltfm: SDHCI platform and OF driver helper
[ 4.872962] sdhci-tegra sdhci-tegra.0: Got CD GPIO
[ 4.873300] sdhci-tegra sdhci-tegra.0: Client registration for eMC Successful
[ 4.873419] sdhci-tegra sdhci-tegra.0: wakeup init done, cdirq 300
[ 4.877844] tegra-se 70012000.se: tegra_se_probe: complete
[ 4.878356] hidraw: raw HID events driver (C) Jiri Kosina
[ 4.879575] usbcore: registered new interface driver usbhid
[ 4.879577] usbhid: USB HID core driver
[ 4.881657] tegra21x_actmon 6000c800.actmon: in actmon_register()...
[ 4.881819] tegra21x_actmon 6000c800.actmon: initialization Completed for the device mc_all
[ 4.883528] nvpmodel: initialized successfully
[ 4.884601] usbcore: registered new interface driver snd-usb-audio
[ 4.884655] No Device Node present for smmu client: snd-soc-dummy !!
[ 4.884660] platform snd-soc-dummy: No iommus property found in DT node, got swgids from fixup(101004000)
[ 4.884676] iommu: Adding device snd-soc-dummy to group 36
[ 4.891215] input: tegra-hda HDMI/DP,pcm=3 as /devices/70030000.hda/sound/card0/input0
[ 4.912476] OPE platform probe
[ 4.912563] OPE platform probe successful
[ 4.912884] OPE platform probe
[ 4.912962] OPE platform probe successful
[ 4.922865] mmc0: SDHCI controller on sdhci-tegra.0 [sdhci-tegra.0] using ADMA 64-bit with 64 bit addr
[ 4.939608] tegra-asoc: sound: ADMAIF1 <-> ADMAIF1 mapping ok
[ 4.939739] tegra-asoc: sound: ADMAIF2 <-> ADMAIF2 mapping ok
[ 4.939859] tegra-asoc: sound: ADMAIF3 <-> ADMAIF3 mapping ok
[ 4.939982] tegra-asoc: sound: ADMAIF4 <-> ADMAIF4 mapping ok
[ 4.940100] tegra-asoc: sound: ADMAIF5 <-> ADMAIF5 mapping ok
[ 4.940219] tegra-asoc: sound: ADMAIF6 <-> ADMAIF6 mapping ok
[ 4.940339] tegra-asoc: sound: ADMAIF7 <-> ADMAIF7 mapping ok
[ 4.940460] tegra-asoc: sound: ADMAIF8 <-> ADMAIF8 mapping ok
[ 4.940579] tegra-asoc: sound: ADMAIF9 <-> ADMAIF9 mapping ok
[ 4.940699] tegra-asoc: sound: ADMAIF10 <-> ADMAIF10 mapping ok
[ 4.952084] u32 classifier
[ 4.952085] Actions configured
[ 4.952157] Initializing XFRM netlink socket
[ 4.952878] NET: Registered protocol family 10
[ 4.953614] NET: Registered protocol family 17
[ 4.953624] NET: Registered protocol family 15
[ 4.953698] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 4.953743] Bluetooth: RFCOMM socket layer initialized
[ 4.953751] Bluetooth: RFCOMM ver 1.11
[ 4.953763] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 4.953767] Bluetooth: HIDP socket layer initialized
[ 4.953785] 9pnet: Installing 9P2000 support
[ 4.953819] Key type dns_resolver registered
[ 4.958547] Registered cp15_barrier emulation handler
[ 4.958602] Registered setend emulation handler
[ 4.961060] registered taskstats version 1
[ 4.962701] Adding domain ve2-pd to PM domain host1x-pd
[ 4.962952] Adding domain ve-pd to PM domain host1x-pd
[ 4.964929] isp 54600000.isp: initialized
[ 4.965853] isp 54680000.isp: initialized
[ 4.975839] last reset is due to software reset
[ 4.975842] KERNEL: PMC reset status reg: 0x3
[ 4.975918] BL: PMC reset status reg: 0x3
[ 4.975919] BL: PMIC poweroff Event Recorder: 0x0
[ 4.977326] clk_cbus_recalc_rate: no gbus parent
[ 4.977330] clk_cbus_round_rate: no gbus parent
[ 4.977331] clk_cbus_round_rate: no gbus parent
[ 4.977338] clk_cbus_recalc_rate: no gbus parent
[ 4.977439] clk_cbus_recalc_rate: no gbus parent
[ 4.977442] clk_cbus_round_rate: no gbus parent
[ 4.977443] clk_cbus_round_rate: no gbus parent
[ 4.977446] clk_cbus_recalc_rate: no gbus parent
[ 4.978140] tegra_dvfs: GPU-cap: registered
[ 4.978192] tegra dvfs: vdd-cpu: nominal 1168mV, offset 708000uV, step 19200uV, scaling enabled
[ 4.978194] tegra dvfs: vdd-core: nominal 1075mV, offset 600000uV, step 12500uV, scaling enabled
[ 4.978196] tegra dvfs: vdd-gpu: nominal 1058mV, offset 708000uV, step 10000uV, scaling enabled
[ 4.980607] tegra_dvfs: vdd-gpu-vts: registered
[ 4.981307] tegra_core_action core_dvfs_cdev_floor: Tegra CORE DVFS 'floor cooling device' registered
[ 4.981948] tegra_core_action core_dvfs_cdev_cap: Tegra CORE DVFS 'cap cooling device' registered
[ 4.982413] input: gpio-keys as /devices/gpio-keys/input/input1
[ 4.985733] mmc0: new SDHC card at address 0001
[ 4.990077] mmcblk0: mmc0:0001 SD16G 29.8 GiB
[ 5.018704] tegra_rtc 7000e000.rtc: setting system clock to 2000-01-01 01:14:53 UTC (946689293)
[ 5.019731] vi 54080000.vi: vi_probe: ++
[ 5.022638] vi 54080000.vi: initialized
[ 5.024600] vi 54080000.vi: subdev nvcsi--1 bound
[ 5.024850] mmcblk mmc0:0001: Card claimed for testing.
[ 5.026123] Disable partitions left on by BL
[ 5.026126] disb
[ 5.026167] bwmgr: missing cdev-type property
[ 5.026258] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[ 5.026262] DRAM derating cdev registered.
[ 5.027238] vdd-fan: disabling
[ 5.027241] vdd-usb-vbus: disabling
[ 5.027242] vdd-usb-vbus2: disabling
[ 5.027251] avdd-io-edp-1v05: disabling
[ 5.027345] ALSA device list:
[ 5.027347] #0: tegra-hda at 0x70038000 irq 83
[ 5.027348] #1: tegra-snd-t210ref-mobile-rt565x
[ 5.160085] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14
[ 5.749692] Freeing unused kernel memory: 8576K
[ 5.774478] Root device found: mmcblk0p1
[ 5.779492] Found dev node: /dev/mmcblk0p1
[ 5.792263] usb 1-2: New USB device found, idVendor=0bda, idProduct=5411
[ 5.798975] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 5.806111] usb 1-2: Product: 4-Port USB 2.1 Hub
[ 5.810726] usb 1-2: Manufacturer: Generic
[ 5.816353] hub 1-2:1.0: USB hub found
[ 5.821222] hub 1-2:1.0: 4 ports detected
[ 6.114815] usb 1-2.1: new low-speed USB device number 3 using tegra-xusb
[ 6.147209] usb 1-2.1: New USB device found, idVendor=040b, idProduct=2000
[ 6.154088] usb 1-2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 6.161393] usb 1-2.1: Product: USB Keyboard
[ 6.165671] usb 1-2.1: Manufacturer: Generic
[ 6.174867] input: Generic USB Keyboard as /devices/70090000.xusb/usb1/1-2/1-2.1/1-2.1:1.0/0003:040B:2000.0001/input/input2
[ 6.243206] hid-generic 0003:040B:2000.0001: input,hidraw0: USB HID v1.10 Keyboard [Generic USB Keyboard] on usb-70090000.xusb-2.1/input0
[ 6.261268] input: Generic USB Keyboard as /devices/70090000.xusb/usb1/1-2/1-2.1/1-2.1:1.1/0003:040B:2000.0002/input/input3
[ 6.331306] hid-generic 0003:040B:2000.0002: input,hidraw1: USB HID v1.10 Mouse [Generic USB Keyboard] on usb-70090000.xusb-2.1/input1
[ 6.422814] usb 1-2.3: new low-speed USB device number 4 using tegra-xusb
[ 6.451687] usb 1-2.3: New USB device found, idVendor=093a, idProduct=2510
[ 6.458566] usb 1-2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 6.465871] usb 1-2.3: Product: USB Optical Mouse
[ 6.470575] usb 1-2.3: Manufacturer: PixArt
[ 6.478158] input: PixArt USB Optical Mouse as /devices/70090000.xusb/usb1/1-2/1-2.3/1-2.3:1.0/0003:093A:2510.0003/input/input4
[ 6.489973] hid-generic 0003:093A:2510.0003: input,hidraw2: USB HID v1.11 Mouse [PixArt USB Optical Mouse] on usb-70090000.xusb-2.3/input0
[ 8.659320] tegra-xusb 70090000.xusb: Upgrade port 0 to USB3.0
[ 8.665147] tegra-xusb 70090000.xusb: Upgrade port 1 to USB3.0
[ 8.987775] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb
[ 9.027970] usb 2-1: New USB device found, idVendor=0bda, idProduct=0411
[ 9.034675] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 9.041807] usb 2-1: Product: 4-Port USB 3.1 Hub
[ 9.046423] usb 2-1: Manufacturer: Generic
[ 9.056306] hub 2-1:1.0: USB hub found
[ 9.061571] hub 2-1:1.0: 4 ports detected
[ 9.222814] usb 2-1: usb_suspend_both: status 0
[ 9.227453] usb usb2: usb_suspend_both: status 0
[ 27.926171] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)
[ 27.935041] Rootfs mounted over mmcblk0p1
[ 67.442803] random: crng init done
[ 82.272866] Switching from initrd to actual rootfs
[ 286.390629] systemd[1]: System time before build time, advancing clock.
[ 306.644183] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 307.993937] cgroup: cgroup2: unknown option "nsdelegate"
[ 315.447228] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GN)
[ 315.469264] systemd[1]: Detected architecture arm64.
[ 318.367176] systemd[1]: No hostname configured.
[ 318.371757] systemd[1]: Set hostname to <localhost>.
[ 321.985068] systemd[1]: Initializing machine ID from random generator.
[ 365.309411] systemd[1]: File /lib/systemd/system/systemd-journald.service:36 configures an IP firewall (IPAddressDeny=any), but the local system d.
[ 365.326461] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.)
[ 410.669142] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 410.678794] systemd[1]: Reached target Swap.
[ 410.685071] systemd[1]: Created slice System Slice.
[ 410.690233] systemd[1]: Listening on RPCbind Server Activation Socket.
[ 410.696962] systemd[1]: Listening on udev Kernel Socket.
[ 410.702490] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 410.709740] systemd[1]: Listening on Journal Socket.
[ 410.844442] systemd[1]: Starting Set the console keyboard layout...
[ 410.853102] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[ 410.864850] systemd[1]: Mounting POSIX Message Queue File System...
[ 440.921212] systemd[1]: Starting Load Kernel Modules...
[ 440.928666] systemd[1]: Starting Nameserver information manager...
[ 440.937496] systemd[1]: Starting Journal Service...
[ 440.942694] systemd[1]: Listening on fsck to fsckd communication Socket.
[ 440.951845] systemd[1]: Starting Remount Root and Kernel File Systems...
[ 440.961727] systemd[1]: Started Create list of required static device nodes for the current kernel.
[ 440.975439] systemd[1]: Starting Create Static Device Nodes in /dev...
[ 443.730917] systemd[1]: Started udev Coldplug all Devices.
[ 453.505550] systemd[1]: Started Journal Service.
[ 477.183800] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null)
[ 533.445768] nvgpu: 57000000.gpu gm20b_init_clk_setup_sw:1268 [INFO] GPCPLL initial settings: NA mode, M=1, N=34, P=3 (id = 1)
[ 586.039097] systemd-journald[2583]: Received request to flush runtime journal from PID 1
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment