Skip to content

Instantly share code, notes, and snippets.

@jmhebert

jmhebert/nano_boot_log_3.txt

Created March 17, 2020 15:23
Show Gist options
  • Star 0 You must be signed in to star a gist
  • Fork 0 You must be signed in to fork a gist
  • Save jmhebert/681ae906cc5d4c724b85e2ea4200003a to your computer and use it in GitHub Desktop.
Save jmhebert/681ae906cc5d4c724b85e2ea4200003a to your computer and use it in GitHub Desktop.
Download ZIP
Nano Boot Serial Console flash.sh
Raw
nano_boot_log_3.txt
[0000.125] [L4T TegraBoot] (version 00.00.2018.01-l4t-39a9dc3d)
[0000.131] Processing in cold boot mode Bootloader 2
[0000.135] A02 Bootrom Patch rev = 1023
[0000.139] Power-up reason: pmc por
[0000.142] No Battery Present
[0000.145] pmic max77620 reset reason
[0000.148] pmic max77620 NVERC : 0x40
[0000.151] RamCode = 0
[0000.154] Platform has DDR4 type RAM
[0000.157] max77620 disabling SD1 Remote Sense
[0000.161] Setting DDR voltage to 1125mv
[0000.165] Serial Number of Pmic Max77663: 0x1727e5
[0000.173] Entering ramdump check
[0000.176] Get RamDumpCarveOut = 0x0
[0000.179] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8
[0000.184] Last reboot was clean, booting normally!
[0000.189] Sdram initialization is successful
[0000.193] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000
[0000.199] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000
[0000.205] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000
[0000.211] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000
[0000.216] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000
[0000.222] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000
[0000.228] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000
[0000.234] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000
[0000.250] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000
[0000.256] Platform-DebugCarveout: 0
[0000.259] Nck Carveout Base=0x00000000ff080000 Size=0x00200000
[0000.265] Non secure mode, and RB not enabled.
[0000.320] Csd NumOfBlocks=62423040
[0000.325] Set High speed to 1
[0000.330] Using GPT Primary to query partitions
[0000.336] Loading Tboot-CPU binary
[0000.345] Verifying TBC in OdmNonSecureSBK mode
[0000.355] Bootloader load address is 0xa0000000, entry address is 0xa0000258
[0000.362] Bootloader downloaded successfully.
[0000.366] Downloaded Tboot-CPU binary to 0xa0000258
[0000.371] MAX77620_GPIO5 configured
[0000.375] CPU power rail is up
[0000.377] CPU clock enabled
[0000.381] Performing RAM repair
[0000.384] Updating A64 Warmreset Address to 0xa00002e9
[0000.389] Loading NvTbootBootloaderDTB
[0000.414] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode
[0000.479] Bootloader DTB Load Address: 0x83000000
[0000.484] Loading NvTbootKernelDTB
[0000.508] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode
[0000.573] Kernel DTB Load Address: 0x83100000
[0000.578] Loading cboot binary
[0000.608] Verifying EBT in OdmNonSecureSBK mode
[0000.649] Bootloader load address is 0x92c00000, entry address is 0x92c00258
[0000.656] Bootloader downloaded successfully.
[0000.673] Using BFS PT to query partitions
[0000.677] Next binary entry address: 0x92c00258
[0000.682] BoardId: 3448
[0000.686] Overriding pmu board id with proc board id
[0000.691] Display board id is not available
[0000.719] Verifying SC7EntryFw in OdmNonSecureSBK mode
[0000.771] /bpmp deleted
[0000.774] SC7EntryFw header found loaded at 0xff700000
[0000.962] OVR2 PMIC
[0000.964] Bpmp FW successfully loaded
[0000.969] WB0 init successfully at 0xff780000
[0000.973] Set NvDecSticky Bits
[0000.976] GSC2 address ff53fffc value c0edbbcc
[0000.983] GSC MC Settings done
[0000.986] TOS Image length 53680
[0000.989] Monitor size 53680
[0000.992] OS size 0
[0000.999] Secure Os AES-CMAC Verification Success!
[0001.004] TOS image cipher info: plaintext
[0001.008] Loading and Validation of Secure OS Successful
[0001.024] SC7 Entry Firmware - 0xff700000, 0x4000
[0001.028] NvTbootPackSdramParams: start.
[0001.033] NvTbootPackSdramParams: done.
[0001.037] Tegraboot started after 52314 us
[0001.041] Basic modules init took 660319 us
[0001.045] Sec Bootdevice Read Time = 12 ms, Read Size = 65 KB
[0001.051] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB
[0001.056] Storage Device Read Time = 109 ms, Read Size = 2226 KB
[0001.062] Storage Device Write Time = 0 ms, Write Size = 0 KB
[0001.067] Next stage binary read took 24535 us
[0001.072] Carveout took -36200 us
[0001.075] CPU initialization took 361422 us
[0001.079] Total time taken by TegraBoot 1010076 us
[0001.083] Starting CPU & Halting co-processor
64NOTICE: BL31: v1.3(release):23b153a63
NOTICE: BL31: Built : 22:39:57, Dec 9 2019
ERROR: Error initializing runtime service trusty_fast
[0001.206] RamCode = 0
[0001.210] LPDDR4 Training: Read DT: Number of tables = 2
[0001.215] EMC Training (SRC-freq: 204000; DST-freq: 1600000)
[0001.228] EMC Training Successful
[0001.231] 408000 not found in DVFS table
[0001.238] RamCode = 0
[0001.241] DT Write: emc-table@204000 succeeded
[0001.246] DT Write: emc-table@1600000 succeeded
[0001.251] LPDDR4 Training: Write DT: Number of tables = 2
[0001.290]
[0001.291] Debug Init done
[0001.294] Marked DTB cacheable
[0001.297] Bootloader DTB loaded at 0x83000000
[0001.301] Marked DTB cacheable
[0001.304] Kernel DTB loaded at 0x83100000
[0001.308] DeviceTree Init done
[0001.324] Pinmux applied successfully
[0001.328] gicd_base: 0x50041000
[0001.332] gicc_base: 0x50042000
[0001.335] Interrupts Init done
[0001.339] Using base:0x60005090 & irq:208 for tick-timer
[0001.344] Using base:0x60005098 for delay-timer
[0001.348] platform_init_timer: DONE
[0001.352] Timer(tick) Init done
[0001.356] osc freq = 38400 khz
[0001.360]
[0001.361] Welcome to L4T Cboot
[0001.364]
[0001.365] Cboot Version: 00.00.2018.01-t210-40c3ff9c
[0001.370] calling constructors
[0001.373] initializing heap
[0001.376] initializing threads
[0001.379] initializing timers
[0001.381] creating bootstrap completion thread
[0001.386] top of bootstrap2()
[0001.389] CPU: ARM Cortex A57
[0001.392] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000
[0001.396] initializing platform
[0001.404] Manufacturer: MF = 0xc2, ID MSB = 0x25
[0001.408] ID LSB = 0x36, ID-CFI len = 194 bytes
[0001.413] Macronix QSPI chip present
[0001.416] SPI device register
[0001.419] init boot device
[0001.422] allocating memory for boot device(SPI)
[0001.426] registering boot device
[0001.436] sdmmc node status = okay
[0001.439] sdcard instance = 0
[0001.442] sdcard gpio handle 0x56
[0001.445] sdcard gpio pin 0xc9
[0001.448] sdcard gpio flags 0x0
[0001.451] vmmc-supply 0x99
[0001.454] Instance: 0
[0001.456] Allocating memory for context
[0001.460] enabling clock
[0001.462] sd card init
[0001.464] Check card present and stable
[0001.468] Send command 0
[0001.484] Send command 3
[0001.489] Set RCA for the card
[0001.492] Query card specific data by command 9
[0001.498] Parse CSD data
[0001.501] Send command 7
[0001.511] Calling sd device register
[0001.514] Init sdcard
[0001.517] Allocating memory for boot device
[0001.521] Registering user device
[0001.534] Enable APE clock
[0001.536] Un-powergate APE partition
[0001.540] of_register: registering tegra_udc to of_hal
[0001.545] of_register: registering inv20628-driver to of_hal
[0001.551] of_register: registering ads1015-driver to of_hal
[0001.556] of_register: registering lp8557-bl-driver to of_hal
[0001.562] of_register: registering bq2419x_charger to of_hal
[0001.568] of_register: registering bq27441_fuel_gauge to of_hal
[0001.579] gpio framework initialized
[0001.583] of_register: registering tca9539_gpio to of_hal
[0001.588] of_register: registering tca9539_gpio to of_hal
[0001.593] of_register: registering i2c_bus_driver to of_hal
[0001.599] of_register: registering i2c_bus_driver to of_hal
[0001.604] of_register: registering i2c_bus_driver to of_hal
[0001.610] pmic framework initialized
[0001.613] of_register: registering max77620_pmic to of_hal
[0001.619] regulator framework initialized
[0001.623] of_register: registering tps65132_bl_driver to of_hal
[0001.629] initializing target
[0001.635] gpio_driver_register: register 'tegra_gpio_driver' driver
[0001.643] board ID = D78, board SKU = 0
[0001.646] Skipping Z3!
[0001.651] fixed regulator driver initialized
[0001.669] initializing OF layer
[0001.672] NCK carveout not present
[0001.675] Skipping dts_overrides
[0001.679] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.696] I2C Bus Init done
[0001.698] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.709] I2C Bus Init done
[0001.711] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.722] I2C Bus Init done
[0001.724] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.735] I2C Bus Init done
[0001.737] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.748] I2C Bus Init done
[0001.750] of_children_init: Ops found for compatible string maxim,max77620
[0001.761] max77620_init using irq 118
[0001.766] register 'maxim,max77620' pmic
[0001.770] gpio_driver_register: register 'max77620-gpio' driver
[0001.776] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.787] I2C Bus Init done
[0001.790] NCK carveout not present
[0001.800] Find /i2c@7000c000's alias i2c0
[0001.804] get eeprom at 1-a0, size 256, type 0
[0001.813] Find /i2c@7000c500's alias i2c2
[0001.817] get eeprom at 3-a0, size 256, type 0
[0001.821] get eeprom at 3-ae, size 256, type 0
[0001.826] pm_ids_update: Updating 1,a0, size 256, type 0
[0001.831] I2C slave not started
[0001.834] I2C write failed
[0001.836] Writing offset failed
[0001.839] eeprom_init: EEPROM read failed
[0001.843] pm_ids_update: eeprom init failed
[0001.848] pm_ids_update: Updating 3,a0, size 256, type 0
[0001.878] pm_ids_update: The pm board id is 3448-0000-200
[0001.884] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0001.892] pm_ids_update: pm id update successful
[0001.897] pm_ids_update: Updating 3,ae, size 256, type 0
[0001.927] pm_ids_update: The pm board id is 3449-0000-200
[0001.933] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0001.941] pm_ids_update: pm id update successful
[0001.972] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0001.978] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0001.986] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0001.992] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0002.000] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e6:53:41
[0002.007] Plugin Manager: Parse ODM data 0x00094000
[0002.017] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0
[0002.038] Find /i2c@7000c000's alias i2c0
[0002.042] get eeprom at 1-a0, size 256, type 0
[0002.051] Find /i2c@7000c500's alias i2c2
[0002.055] get eeprom at 3-a0, size 256, type 0
[0002.059] get eeprom at 3-ae, size 256, type 0
[0002.064] pm_ids_update: Updating 1,a0, size 256, type 0
[0002.069] I2C slave not started
[0002.072] I2C write failed
[0002.075] Writing offset failed
[0002.078] eeprom_init: EEPROM read failed
[0002.082] pm_ids_update: eeprom init failed
[0002.086] pm_ids_update: Updating 3,a0, size 256, type 0
[0002.116] pm_ids_update: The pm board id is 3448-0000-200
[0002.122] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0002.129] pm_ids_update: pm id update successful
[0002.134] pm_ids_update: Updating 3,ae, size 256, type 0
[0002.164] pm_ids_update: The pm board id is 3449-0000-200
[0002.170] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0002.177] pm_ids_update: pm id update successful
[0002.208] Add serial number:1422419088143 as DT property
[0002.216] Applying platform configs
[0002.222] platform-init is not present. Skipping
[0002.227] calling apps_init()
[0002.247] Found 14 GPT partitions in "sd0"
[0002.251] Proceeding to Cold Boot
[0002.254] starting app android_boot_app
[0002.258] Device state: unlocked
[0002.261] display console init
[0002.269] could not find regulator
[0002.293] hdmi cable not connected
[0002.296] is_hdmi_needed: HDMI not connected, returning falDT entry for leds-pwm not found
s[0002.308] e
[0002.309] hdmi is not connected
[0002.312] sor0 is not supported
[0002.315] display_console_init: no valid display out_type
[0002.323] subnode volume_up is not found !
[0002.327] subnode back is not found !
[0002.331] subnode volume_down is not found !
[0002.335] subnode menu is not found !
[0002.338] Gpio keyboard init success
[0002.382] found decompressor handler: lz4-legacy
[0002.397] decompressing blob (type 1)...
[0002.430] display_resolution: No display init
[0002.434] Failed to retrieve display resolution
[0002.439] Could not load/initialize BMP blob...ignoring
[0002.490] decompressor handler not found
[0002.494] load_firmware_blob: Firmware blob loaded, entries=2
[0002.500] -------> se_aes_verify_sbk_clear: 747
[0002.504] se_aes_verify_sbk_clear: Error
[0002.508] bl_battery_charging: connected to external power supply
[0002.515] xusb is supported
[0002.521] error while finding nvidia,portmap
[0003.026] xusb blob version 0 size 124416
[0003.029] firmware size 124416
[0003.034] Firmware timestamp: 0x5da88fc3, Version: 50.25 release
[0003.041] xhci0: 64 bytes context size, 32-bit DMA
[0003.081] usbus0: 5.0Gbps Super Speed USB v3.0
[0003.101] uhub0: <Nvidia XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
[0003.751] uhub0: 9 ports with 9 removable, self powered
[0004.751] failed to get HID devices
[0004.755] failed to init xhci or no usb device attached
[0004.762] display_console_ioctl: No display init
[0004.767] switch_backlight failed
[0004.773] device_query_partition_size: failed to open partition sd0:MSC !
[0004.780] MSC Partition not found
[0004.786] device_query_partition_size: failed to open partition sd0:USP !
[0004.793] USP partition read failed!
[0004.796] blob_init: blob-partition USP header read failed
[0004.802] android_boot Unable to update recovery partition
[0004.807] kfs_getpartname: name = LNX
[0004.811] Loading kernel from LNX
[0004.909] load kernel from storage
[0004.920] decompressor handler not found
[0004.978] Successfully loaded kernel and ramdisk images
[0004.984] display_resolution: No display init
[0004.989] Failed to retrieve display resolution
[0004.993] bmp blob is not loaded and initialized
[0004.998] Failed to display boot-logo
[0005.001] NCK carveout not present
[0005.005] Skipping dts_overrides
[0005.008] NCK carveout not present
[0005.018] Find /i2c@7000c000's alias i2c0
[0005.022] get eeprom at 1-a0, size 256, type 0
[0005.030] Find /i2c@7000c500's alias i2c2
[0005.034] get eeprom at 3-a0, size 256, type 0
[0005.039] get eeprom at 3-ae, size 256, type 0
[0005.043] pm_ids_update: Updating 1,a0, size 256, type 0
[0005.048] I2C slave not started
[0005.051] I2C write failed
[0005.054] Writing offset failed
[0005.057] eeprom_init: EEPROM read failed
[0005.061] pm_ids_update: eeprom init failed
[0005.065] pm_ids_update: Updating 3,a0, size 256, type 0
[0005.095] pm_ids_update: The pm board id is 3448-0000-200
[0005.102] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0005.110] pm_ids_update: pm id update successful
[0005.114] pm_ids_update: Updating 3,ae, size 256, type 0
[0005.144] pm_ids_update: The pm board id is 3449-0000-200
[0005.151] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0005.159] pm_ids_update: pm id update successful
[0005.189] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0005.195] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0005.203] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0005.209] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0005.218] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e6:53:41
[0005.224] Plugin Manager: Parse ODM data 0x00094000
[0005.235] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0
[0005.249] Add serial number:1422419088143 as DT property
[0005.258] "bpmp" doesn't exist, creating
[0005.264] Updated bpmp info to DTB
[0005.269] Updated initrd info to DTB
[0005.272] "proc-board" doesn't exist, creating
[0005.278] Updated board info to DTB
[0005.281] "pmu-board" doesn't exist, creating
[0005.287] Updated board info to DTB
[0005.290] "display-board" doesn't exist, creating
[0005.296] Updated board info to DTB
[0005.299] "reset" doesn't exist, creating
[0005.304] Updated reset info to DTB
[0005.307] display_console_ioctl: No display init
[0005.311] display_console_ioctl: No display init
[0005.316] display_console_ioctl: No display init
[0005.321] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000
[0005.355] DTB cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0
[0005.367] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0
[0005.380] Updated bootarg info to DTB
[0005.384] Adding uuid 00000001644495821c00000011fd8280 to DT
[0005.390] Adding eks info 0 to DT
[0005.395] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7
[0005.401] Updated memory info to DTB
[0005.407] Updated system-lp0-disable info to DTB
[0005.415] set vdd_core voltage to 1075 mv
[0005.419] setting 'vdd-core' regulator to 1075000 micro volts
[0005.441] Found secure-pmc; disable BPMP
U-Boot 2016.07-g0536cf2a27 (Dec 09 2019 - 22:40:32 -0800)
TEGRA210
Model: NVIDIA P3450-Porg
Board: NVIDIA P3450-PORG
DRAM: 4 GiB
MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1
SF: Detected MX25U3235F with page size 256 Bytes, erase size 4 KiB, total 4 MiB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Hit any key to stop autoboot: 1  0
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/extlinux.conf
734 bytes read in 173 ms (3.9 KiB/s)
1: primary kernel
Retrieving file: /boot/initrd
5487751 bytes read in 542 ms (9.7 MiB/s)
Retrieving file: /boot/Image
34191368 bytes read in 2934 ms (11.1 MiB/s)
## Flattened Device Tree blob at 83100000
Booting using the fdt blob at 0x83100000
reserving fdt memory region: addr=80000000 size=20000
Using Device Tree in place at 0000000083100000, end 00000000831776f0
Starting kernel ...
<hit enter to activate fiq debugger>
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.9.140-tegra (buildbrain@mobile-u64-2713) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Mon Dec 9 22:47:42 PST 2019
[ 0.000000] Boot CPU: AArch64 Processor [411fd071]
[ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 48,
[ 0.000000] OF: fdt: - 80000000 , 7ee00000
[ 0.000000] OF: fdt: - 100000000 , 7f200000
[ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB
[ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB
[ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB
[ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB
[ 0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout
[ 0.000000] OF: reserved mem: initialized node iram-carveout, compatible id nvidia,iram-carveout
[ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops
[ 0.000000] cma: Reserved 64 MiB at 0x00000000fac00000
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.1
[ 0.000000] percpu: Embedded 25 pages/cpu @ffffffc0fefb1000 s61592 r8192 d32616 u102400
[ 0.000000] CPU features: enabling workaround for ARM erratum 832075
[ 0.000000] Speculative Store Bypass Disable mitigation not required
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1023544
[ 0.000000] Kernel command line: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0
[ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes
[ 0.000000] log_buf_len total cpu_extra contributions: 98304 bytes
[ 0.000000] log_buf_len min size: 32768 bytes
[ 0.000000] log_buf_len: 131072 bytes
[ 0.000000] early log buf free: 29500(90%)
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] Memory: 3570416K/4159488K available (15230K kernel code, 2926K rwdata, 6620K rodata, 8576K init, 609K bss, 113936K reserved, 475136K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB)
[ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB)
[ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008f60000 ( 15232 KB)
[ 0.000000] .rodata : 0xffffff8008f60000 - 0xffffff80095e0000 ( 6656 KB)
[ 0.000000] .init : 0xffffff80095e0000 - 0xffffff8009e40000 ( 8576 KB)
[ 0.000000] .data : 0xffffff8009e40000 - 0xffffff800a11b808 ( 2927 KB)
[ 0.000000] .bss : 0xffffff800a11b808 - 0xffffff800a1b3dbc ( 610 KB)
[ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB)
[ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB)
[ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum)
[ 0.000000] 0xffffffbf00000000 - 0xffffffbf03fc8000 ( 63 MB actual)
[ 0.000000] memory : 0xffffffc000000000 - 0xffffffc0ff200000 ( 4082 MB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 64.
[ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[ 0.000000] NR_IRQS:64 nr_irqs:64 0
[ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller
[ 0.000000] t210 clock and reset probe
[ 0.000000] tegra-pmc: get_secure_pmc_setting: done secure_pmc=1
[ 0.000000] clk_cbus_recalc_rate: no gbus parent
[ 0.000000] clk_cbus_recalc_rate: no gbus parent
[ 0.000000] clk_cbus_recalc_rate: no gbus parent
[ 0.000000] clk_cbus_recalc_rate: no gbus parent
[ 0.000000] clk_cbus_recalc_rate: no gbus parent
[ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[ 0.000006] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[ 0.001674] Console: colour dummy device 80x25
[ 0.002507] console [tty0] enabled
[ 0.002534] kmemleak: Kernel memory leak detector disabled
[ 0.002564] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800)
[ 0.002594] pid_max: default: 32768 minimum: 301
[ 0.003052] Security Framework initialized
[ 0.003284] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.003304] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.004503] ftrace: allocating 47001 entries in 184 pages
[ 0.176601] ASID allocator initialised with 65536 entries
[ 0.215861] tegra-id: chipid=22117.
[ 0.215904] tegra-id: opt_subrevision=0.
[ 0.215933] Tegra Speedo/IDDQ fuse revision 4
[ 0.215949] Tegra: CPU Speedo ID 9, SoC Speedo ID 0, GPU Speedo ID 2
[ 0.215965] Tegra: CPU Process ID 0, SoC Process ID 1, GPU Process ID 0
[ 0.215981] Tegra: CPU Speedo Value 2084, SoC Speedo Value 1976, GPU Speedo Value 2075
[ 0.216003] Tegra: CPU IDDQ Value 1872, SoC IDDQ Value 1980, GPU IDDQ Value 2430
[ 0.216038] Tegra Revision: A02 SKU: 0x8f CPU Process: 0 SoC Process: 1
[ 0.216064] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0000-p3449-0000-a02.dts
[ 0.216097] DTB Build time: Dec 9 2019 22:51:54
[ 0.265030] CPU1: Booted secondary processor [411fd071]
[ 0.296976] CPU2: Booted secondary processor [411fd071]
[ 0.328943] CPU3: Booted secondary processor [411fd071]
[ 0.329032] Brought up 4 CPUs
[ 0.329095] SMP: Total of 4 processors activated.
[ 0.329114] CPU features: detected feature: 32-bit EL0 Support
[ 0.329387] CPU: All CPU(s) started at EL2
[ 0.329419] alternatives: patching kernel code
[ 0.337453] devtmpfs: initialized
[ 0.374610] Initilizing CustomIPI irq domain
[ 0.375031] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.375076] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.385595] pinctrl core: initialized pinctrl subsystem
[ 0.386281] OS set in device tree is not L4T.
[ 0.386691] regulator-dummy: no parameters
[ 0.386989] Initializing plugin-manager
[ 0.387114] Plugin module not found
[ 0.387356] node /plugin-manager/fragement@0 match with board >=3448-0000-100
[ 0.387908] node /plugin-manager/fragment@1 match with board >=3448-0000-101
[ 0.388778] node /plugin-manager/fragment@5 match with board 3449-0000-200
[ 0.389266] node /plugin-manager/fragement@6 match with odm-data enable-tegra-wdt
[ 0.389707] node /plugin-manager/fragement@8 match with odm-data enable-tegra-wdt
[ 0.390112] node /plugin-manager/fragement@9 match with board <3448-0000-300
[ 0.394905] NET: Registered protocol family 16
[ 0.396184] pstore: using zlib compression
[ 0.396856] console [pstore-1] enabled
[ 0.396873] pstore: Registered ramoops as persistent store backend
[ 0.396892] ramoops: attached 0x200000@0xb0000000, ecc: 0/0
[ 0.413049] cpuidle: using governor menu
[ 0.417242] tegra_smmu 70019000.iommu: Loaded Tegra IOMMU driver
[ 0.418830] vdso: 2 pages (1 code @ ffffff8008f67000, 1 data @ ffffff8009e44000)
[ 0.418875] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.421492] atomic_pool_init():622: DMA: preallocated 1024 KiB pool for atomic allocations
[ 0.424073] tegra_powergate_init: DONE
[ 0.424110] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0000-p3449-0000-a02.dts
[ 0.424147] DTB Build time: Dec 9 2019 22:51:54
[ 0.425875] Tegra reboot handler registered.
[ 0.430317] iommu: Adding device tegra-carveouts to group 0
[ 0.430486] platform tegra-carveouts: domain=ffffffc0f9baa318 allocates as[0]=ffffffc0f9bd40a8
[ 0.430855] iommu: Adding device smmu_test to group 1
[ 0.430924] platform smmu_test: domain=ffffffc0f9baa558 allocates as[0]=ffffffc0f9bd4110
[ 0.431746] mc: mapped MMIO address: 0xffffff800802e000 -> 0x70019000
[ 0.431825] mc: mapped MMIO address: 0xffffff8008065000 -> 0x7001c000
[ 0.431893] mc: mapped MMIO address: 0xffffff8008079000 -> 0x7001d000
[ 0.431917] nv-tegra-mc 70019000.mc: No mssnvlink node
[ 0.431951] mc-err: mcerr ops are set to t21x
[ 0.441705] iommu: Adding device 70090000.xusb to group 2
[ 0.442025] iommu: Adding device 70006000.serial to group 3
[ 0.442121] platform 70006000.serial: domain=ffffffc0f94ad618 allocates as[0]=ffffffc0f9bd4178
[ 0.442555] iommu: Adding device 70006040.serial to group 4
[ 0.442850] iommu: Adding device 70006200.serial to group 5
[ 0.443095] iommu: Adding device sound to group 6
[ 0.443162] platform sound: domain=ffffffc0f94adb58 allocates as[0]=ffffffc0f9bd41e0
[ 0.443738] iommu: Adding device 7000d400.spi to group 7
[ 0.444013] iommu: Adding device 7000d600.spi to group 8
[ 0.444304] iommu: Adding device 70410000.spi to group 9
[ 0.444630] iommu: Adding device 50000000.host1x to group 10
[ 0.444910] iommu: Adding device 54080000.vi to group 11
[ 0.445378] iommu: Adding device 54600000.isp to group 12
[ 0.445658] iommu: Adding device 54680000.isp to group 13
[ 0.445978] iommu: Adding device tegradc.0 to group 14
[ 0.446049] platform tegradc.0: domain=ffffffc0f94baa98 allocates as[0]=ffffffc0f9bd4248
[ 0.446573] platform tegradc.0: IOVA linear map 0x00000000d7000000(19000000)
[ 0.446911] iommu: Adding device tegradc.1 to group 15
[ 0.446974] platform tegradc.1: domain=ffffffc0f94bacd8 allocates as[0]=ffffffc0f9bd42b0
[ 0.447501] platform tegradc.1: IOVA linear map 0x00000000d7000000(19000000)
[ 0.447759] iommu: Adding device 54340000.vic to group 16
[ 0.447982] iommu: Adding device 544c0000.nvenc to group 17
[ 0.448197] iommu: Adding device 54500000.tsec to group 18
[ 0.448409] iommu: Adding device 54100000.tsecb to group 19
[ 0.448616] iommu: Adding device 54480000.nvdec to group 20
[ 0.448850] iommu: Adding device 54380000.nvjpg to group 21
[ 0.450109] iommu: Adding device 546c0000.i2c to group 22
[ 0.450462] iommu: Adding device 57000000.gpu to group 23
[ 0.450532] platform 57000000.gpu: domain=ffffffc0f94c5cd8 allocates as[0]=ffffffc0f9bd4318
[ 0.450589] platform 57000000.gpu: domain=ffffffc0f94c5cd8 allocates as[1]=ffffffc0f9bd4380
[ 0.450651] platform 57000000.gpu: domain=ffffffc0f94c5cd8 allocates as[2]=ffffffc0f9bd43e8
[ 0.450707] platform 57000000.gpu: domain=ffffffc0f94c5cd8 allocates as[3]=ffffffc0f9bd4450
[ 0.451613] tegra-pmc 7000e400.pmc: i2c-thermtrip node not found, emergency thermal reset disabled.
[ 0.451653] tegra-pmc 7000e400.pmc: scratch reg offset dts data not present
[ 0.451679] tegra-pmc: ### PMC reset source: TEGRA_POWER_ON_RESET
[ 0.451699] tegra-pmc: ### PMC reset level: TEGRA_RESET_LEVEL_WARM
[ 0.451716] tegra-pmc: ### PMC reset status reg: 0x0
[ 0.501153] padctrl padctrl.0: Pad control driver tegra-pmc-padctrl registered
[ 0.501190] tegra-pmc: Clear bootloader IO dpd settings
[ 0.501227] tegra-pmc 7000e400.pmc: IO padctrl driver initialized
[ 0.501306] tegra-pmc 7000e400.pmc: PMC: Successfully configure bootrom reset commands
[ 0.501609] iommu: Adding device 70012000.se to group 24
[ 0.502388] iommu: Adding device 7000c000.i2c to group 25
[ 0.502652] iommu: Adding device 7000c400.i2c to group 26
[ 0.502921] iommu: Adding device 7000c500.i2c to group 27
[ 0.503187] iommu: Adding device 7000c700.i2c to group 28
[ 0.503480] iommu: Adding device 7000d000.i2c to group 29
[ 0.503740] iommu: Adding device 7000d100.i2c to group 30
[ 0.504041] iommu: Adding device sdhci-tegra.0 to group 31
[ 0.504112] platform sdhci-tegra.0: domain=ffffffc0f955de58 allocates as[0]=ffffffc0f9bd44b8
[ 0.504959] iommu: Adding device 700d0000.xudc to group 32
[ 0.508342] vdd-ac-bat: 5000 mV
[ 0.508727] vdd-5v0-sys: 5000 mV
[ 0.509724] vdd-5v0-hdmi: supplied by vdd-5v0-sys
[ 0.509805] vdd-5v0-hdmi: 5000 mV
[ 0.510211] vdd-1v8-sys: 1800 mV
[ 0.510617] vdd-fan: supplied by vdd-5v0-sys
[ 0.510673] vdd-fan: 5000 mV
[ 0.511060] vdd-usb-vbus: supplied by vdd-5v0-sys
[ 0.511130] vdd-usb-vbus: 5000 mV
[ 0.511656] vdd-usb-vbus2: 5000 mV
[ 0.541857] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.544205] gpio gpiochip0: gpio-line-names specifies 240 line names but there are 256 lines on the chip
[ 0.545788] GPIO line 151 (camera-control-output-low) hogged as output/low
[ 0.545829] GPIO line 152 (camera-control-output-low) hogged as output/low
[ 0.546219] gpiochip_setup_dev: registered GPIOs 0 to 255 on device: gpiochip0 (tegra-gpio)
[ 0.554203] eventlib_kernel: keventlib is initialized, test id: 0
[ 0.554589] SCSI subsystem initialized
[ 0.555105] usbcore: registered new interface driver usbfs
[ 0.555185] usbcore: registered new interface driver hub
[ 0.555274] usbcore: registered new device driver usb
[ 0.559173] max77620 4-003c: PMIC Version OTP:0x35 and ES:0x8
[ 0.565153] vdd-core: 600 <--> 1162 mV at 1075 mV
[ 0.565819] random: fast init done
[ 0.566171] vdd-ddr-1v1: Bringing 1125000uV into 1150000-1150000uV
[ 0.569050] vdd-ddr-1v1: 1150 mV
[ 0.573044] vdd-pre-reg-1v35: 1350 mV
[ 0.577044] vdd-1v8: 1800 mV
[ 0.581044] avdd-sys-1v2: 1200 mV
[ 0.585041] vdd-pex-1v0: 1050 mV
[ 0.585715] vddio-sdmmc-ap: 1800 <--> 3300 mV at 3300 mV
[ 0.586275] max77620-ldo3: at 3100 mV
[ 0.589045] vdd-rtc: 850 <--> 1100 mV at 1000 mV
[ 0.589599] max77620-ldo5: at 3100 mV
[ 0.590163] max77620-ldo6: at 2800 mV
[ 0.593041] avdd-1v05-pll: 1050 mV
[ 0.597042] avdd-io-hdmi-dp: 1050 mV
[ 0.599645] GPIO line 505 (spmic-default-output-high) hogged as output/high
[ 0.599964] gpiochip_setup_dev: registered GPIOs 504 to 511 on device: gpiochip1 (max77620-gpio)
[ 0.600271] max77620 4-003c: max77620 probe successful
[ 0.602977] media: Linux media interface: v0.10
[ 0.603057] Linux video capture interface: v2.00
[ 0.603964] pps_core: LinuxPPS API ver. 1 registered
[ 0.603993] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.604032] PTP clock support registered
[ 0.607831] tegra_fiq_debugger_init: found FIQ source (IRQ 98)
[ 0.614121] tegra210-emc 7001b000.external-memory-controller: validated EMC DFS table
[ 0.614933] Advanced Linux Sound Architecture Driver Initialized.
[ 0.615569] Bluetooth: Core ver 2.22
[ 0.615634] NET: Registered protocol family 31
[ 0.615652] Bluetooth: HCI device and connection manager initialized
[ 0.615681] Bluetooth: HCI socket layer initialized
[ 0.615703] Bluetooth: L2CAP socket layer initialized
[ 0.615740] Bluetooth: SCO socket layer initialized
[ 0.617432] tegra210_dvfs: no clock found for sdmmc2_ddr
[ 0.617469] tegra210_dvfs: no clock found for sdmmc4_ddr
[ 0.617529] tegra210_dvfs: no clock found for sdmmc1_ddr
[ 0.617556] tegra210_dvfs: no clock found for sdmmc3_ddr
[ 0.620660] tegra_dvfs: Unable to get vdd-cpu rail for step info, defering probe
[ 0.621843] vdd-3v3-sys: supplied by vdd-5v0-sys
[ 0.621954] vdd-3v3-sys: 3300 mV
[ 0.622212] vdd-1v8-sys: supplied by vdd-3v3-sys
[ 0.625107] vdd-usb-vbus2: supplied by vdd-3v3-sys
[ 0.625577] vdd-3v3-sd: supplied by vdd-3v3-sys
[ 0.625630] vdd-3v3-sd: 3300 mV
[ 0.626711] avdd-io-edp-1v05: supplied by avdd-1v05-pll
[ 0.626771] avdd-io-edp-1v05: 1050 mV
[ 0.627253] vdd-usb-hub-en: supplied by vdd-1v8-sys
[ 0.627303] vdd-usb-hub-en: 5000 mV
[ 0.628698] camchar: rtcpu character device driver loaded
[ 0.629509] extcon-gpio-states extcon:extcon@1: Cable state:1, cable id:1
[ 0.630965] clocksource: Switched to clocksource arch_sys_counter
[ 0.670026] VFS: Disk quotas dquot_6.6.0
[ 0.670194] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.670693] nvmap_heap_init: nvmap_heap_init: created heap block cache
[ 0.671171] dma_declare_coherent_resizable_cma_memory:324: resizable heap=vpr, base=0x00000000d7000000, size=0x19000000
[ 0.671224] dma-vpr: heap size is not multiple of cma_chunk_size heap_info->num_chunks (13) rem_chunk_size(0x1000000)
[ 0.671429] cma: enabled page replacement for spfn=d7000, epfn=f0000
[ 0.671452] dma_declare_coherent_resizable_cma_memory:373: resizable cma heap=vpr create successful
[ 0.671481] tegra-carveouts tegra-carveouts: assigned reserved memory node vpr-carveout
[ 0.671531] tegra-carveouts tegra-carveouts: iram :dma coherent mem declare 0x0000000040001000,258048
[ 0.671558] tegra-carveouts tegra-carveouts: assigned reserved memory node iram-carveout
[ 0.671590] nvmap: nvmap_select_cache_ops() nvmap cache ops set to set/ways
[ 0.671613] nvmap_page_pool_init: Total RAM pages: 1011388
[ 0.671630] nvmap_page_pool_init: nvmap page pool size: 126423 pages (493 MB)
[ 0.671902] nvmap_background_zero_thread: PP zeroing thread starting.
[ 0.672190] misc nvmap: created heap iram base 0x0000000040001000 size (252KiB)
[ 0.673097] misc nvmap: created heap vpr base 0x00000000d7000000 size (409600KiB)
[ 0.681224] thermal thermal_zone0: Registering thermal zone thermal_zone0 for type AO-therm
[ 0.681652] thermal thermal_zone1: Registering thermal zone thermal_zone1 for type CPU-therm
[ 0.681915] thermal thermal_zone2: Registering thermal zone thermal_zone2 for type GPU-therm
[ 0.682131] thermal thermal_zone3: Registering thermal zone thermal_zone3 for type PLL-therm
[ 0.682328] thermal thermal_zone4: Registering thermal zone thermal_zone4 for type PMIC-Die
[ 0.682616] pre_t19x_iso_plat_init(): iso emc max clk=1600000KHz
[ 0.682640] pre_t19x_iso_plat_init(): max_iso_bw=11520000KB
[ 0.683132] NET: Registered protocol family 2
[ 0.684118] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.684355] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[ 0.684862] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.685027] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.685125] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.685552] NET: Registered protocol family 1
[ 0.686334] RPC: Registered named UNIX socket transport module.
[ 0.686363] RPC: Registered udp transport module.
[ 0.686380] RPC: Registered tcp transport module.
[ 0.686399] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.686658] Trying to unpack rootfs image as initramfs...
[ 0.918435] Freeing initrd memory: 5356K
[ 0.928506] host1x 50000000.host1x: initialized
[ 0.930267] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[ 0.933552] audit: initializing netlink subsys (disabled)
[ 0.933672] audit: type=2000 audit(0.783:1): initialized
[ 0.934484] workingset: timestamp_bits=46 max_order=20 bucket_order=0
[ 0.944474] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.946006] ntfs: driver 2.1.32 [Flags: R/W].
[ 0.946811] 9p: Installing v9fs 9p2000 file system support
[ 0.950180] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 240)
[ 0.950348] io scheduler noop registered
[ 0.950652] io scheduler cfq registered (default)
[ 0.953335] gic 702f9000.agic: GIC IRQ controller registered
[ 0.956348] iommu: Adding device 702ef000.adsp to group 33
[ 0.965664] iommu: Adding device aconnect@702c0000:adsp_audio to group 34
[ 0.965882] tegra-aconnect aconnect@702c0000: Tegra ACONNECT bus registered
[ 0.966486] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_SKU_CALIB_0 = 0x8229413
[ 0.966518] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_USB_CALIB_EXT_0 = 0x4
[ 0.968240] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.0, lane = usb2-0, function = xusb
[ 0.968376] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.1, lane = usb2-1, function = xusb
[ 0.968492] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.2, lane = usb2-2, function = xusb
[ 0.968695] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.3, lane = pcie-0, function = pcie-x1
[ 0.968805] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.4, lane = pcie-1, function = pcie-x4
[ 0.968913] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.5, lane = pcie-2, function = pcie-x4
[ 0.969022] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.6, lane = pcie-3, function = pcie-x4
[ 0.969128] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.7, lane = pcie-4, function = pcie-x4
[ 0.969233] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.8, lane = pcie-5, function = xusb
[ 0.969341] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.9, lane = pcie-6, function = xusb
[ 0.975343] tegra-pwm 7000a000.pwm: PWM clk cannot sleep in ops
[ 0.977041] tegra-dfll-pwm 70110000.pwm: DFLL pwm-rate: 12800000
[ 0.979000] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration
[ 0.980292] tegra-pcie 1003000.pcie: PCIE: Enable power rails
[ 0.980670] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes
[ 0.981856] tegra_camera_platform tegra-camera-platform: tegra_camera_probe:camera_platform_driver probe
[ 0.982097] misc tegra_camera_ctrl: tegra_camera_isomgr_register isp_iso_bw=1500000, vi_iso_bw=750000, max_bw=1500000
[ 0.982372] Adding domain tsec-pd to PM domain host1x-pd
[ 0.984678] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes
[ 0.985615] tsec 54500000.tsec: initialized
[ 0.987179] tsec 54100000.tsecb: initialized
[ 0.987869] Adding domain nvdec-pd to PM domain host1x-pd
[ 0.991290] nvdec 54480000.nvdec: initialized
[ 0.992344] Adding domain vic03-pd to PM domain host1x-pd
[ 0.992547] Adding domain msenc-pd to PM domain host1x-pd
[ 0.992718] Adding domain nvjpg-pd to PM domain host1x-pd
[ 0.996675] falcon 54340000.vic: initialized
[ 0.997970] falcon 544c0000.nvenc: initialized
[ 0.999310] falcon 54380000.nvjpg: initialized
[ 1.003618] tegra_cec 70015000.tegra_cec: dt=1 start=0x70015000 end=0x70015FFF irq=97
[ 1.003695] tegra_cec 70015000.tegra_cec: Enable clock result: 0.
[ 1.003750] tegra_cec 70015000.tegra_cec: tegra_cec_init started
[ 1.003800] tegradc tegradc.0: disp0 connected to head0->/host1x/sor1
[ 1.003942] display board info: id 0x0, fab 0x0
[ 1.004023] generic_infoframe_type: 0x87
[ 1.004047] tegra_cec 70015000.tegra_cec: cec_add_sysfs ret=0
[ 1.004070] tegra_cec 70015000.tegra_cec: probed
[ 1.004196] tegradc tegradc.0: DT parsed successfully
[ 1.004266] tegradc tegradc.0: Display dc.ffffff800ab40000 registered with id=0
[ 1.008015] tegradc tegradc.0: probed
[ 1.008744] Console: switching to colour frame buffer device 80x30
[ 1.008800] tegradc tegradc.0: fb registered
[ 1.010002] tegradc tegradc.1: disp1 connected to head1->/host1x/sor
[ 1.010114] tegradc tegradc.1: No lt-data, using default setting
[ 1.010152] tegradc tegradc.1: No hpd-gpio in DT
[ 1.010194] tegradc tegradc.1: DT parsed successfully
[ 1.010251] tegradc tegradc.1: Display dc.ffffff800acc0000 registered with id=1
[ 1.012176] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels
[ 1.012650] tegradc tegradc.1: dpd enable lookup fail:-19
[ 1.518800] Host read timeout at address 545c00c4
[ 1.520090] tegra-adma 702e2000.adma: Tegra210 ADMA driver registered 22 channels
[ 1.520446] tegradc tegradc.1: probed
[ 1.520812] tegradc tegradc.1: fb registered
[ 1.520919] tegra-fuse-burn 7000f800.efuse:efuse-burn: Fuse burn driver initialized
[ 1.521239] kfuse 7000fc00.kfuse: initialized
[ 1.522120] tegra-pmc-iopower pmc-iopower: Regulator supply iopower-dbg-supply not available
[ 1.523004] tegra-pmc-iopower pmc-iopower: NO_IOPOWER setting 0x0
[ 1.523962] tegra-dfll-pwm 70110000.pwm: DFLL_PWM regulator is available now
[ 1.523990] vdd-cpu: 708 <--> 1322 mV at 708 mV
[ 1.524092] hpd: state 7 (Takeover from bootloader), hpd 0, pending_hpd_evt 1
[ 1.524113] hpd: switching from state 7 (Takeover from bootloader) to state 0 (Reset)
[ 1.524135] hpd: state 0 (Reset), hpd 0, pending_hpd_evt 0
[ 1.524163] tegradc tegradc.1: blank - powerdown
[ 1.524197] extcon-disp-state extcon:disp-state: cable 44 state 0 already set.
[ 1.524214] Extcon DP: HPD disabled
[ 1.524227] hpd: hpd_switch 0
[ 1.524240] hpd: switching from state 0 (Reset) to state 1 (Check Plug)
[ 1.524261] hpd: state 1 (Check Plug), hpd 0, pending_hpd_evt 0
[ 1.524277] hpd: switching from state 1 (Check Plug) to state 3 (Disabled)
[ 1.524386] pwm-regulator pwm_regulators:pwm-regulator@0: PWM regulator registration passed
[ 1.525723] vdd-gpu: applied init 1000000uV constraint
[ 1.525744] vdd-gpu: 708 <--> 1323 mV at 997 mV
[ 1.526111] pwm-regulator pwm_regulators:pwm-regulator@1: PWM regulator registration passed
[ 1.529634] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.529760] No Device Node present for smmu client: serial8250 !!
[ 1.529781] platform serial8250: No iommus property found in DT node, got swgids from fixup(101004000)
[ 1.529832] iommu: Adding device serial8250 to group 35
[ 1.532252] console [ttyS0] disabled
[ 1.532363] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 63, base_baud = 25500000) is a Tegra
[ 1.930722] tegra-pcie 1003000.pcie: link 0 down, retrying
[ 2.038982] tegra_cec 70015000.tegra_cec: Can't find physical addresse.
[ 2.038986] tegra_cec 70015000.tegra_cec: tegra_cec_init Done.
[ 2.334684] tegra-pcie 1003000.pcie: link 0 down, retrying
[ 2.739008] tegra-pcie 1003000.pcie: link 0 down, retrying
[ 2.741025] tegra-pcie 1003000.pcie: link 0 down, ignoring
[ 2.847230] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00
[ 2.847240] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 2.847245] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff]
[ 2.847250] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref]
[ 2.847255] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 2.847646] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 2.859108] pci 0000:00:02.0: BAR 14: assigned [mem 0x13000000-0x130fffff]
[ 2.859113] pci 0000:00:02.0: BAR 13: assigned [io 0x1000-0x1fff]
[ 2.859123] pci 0000:01:00.0: BAR 4: assigned [mem 0x13000000-0x13003fff 64bit]
[ 2.859144] pci 0000:01:00.0: BAR 2: assigned [mem 0x13004000-0x13004fff 64bit]
[ 2.859162] pci 0000:01:00.0: BAR 0: assigned [io 0x1000-0x10ff]
[ 2.859173] pci 0000:00:02.0: PCI bridge to [bus 01]
[ 2.859178] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff]
[ 2.859185] pci 0000:00:02.0: bridge window [mem 0x13000000-0x130fffff]
[ 2.859565] pcieport 0000:00:02.0: Signaling PME through PCIe PME interrupt
[ 2.859569] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
[ 4.056452] console [ttyS0] enabled
[ 4.061125] 70006040.serial: ttyTHS1 at MMIO 0x70006040 (irq = 64, base_baud = 0) is a TEGRA_UART
[ 4.070318] serial-tegra 70006200.serial: RX in PIO mode
[ 4.075755] 70006200.serial: ttyTHS2 at MMIO 0x70006200 (irq = 65, base_baud = 0) is a TEGRA_UART
[ 4.085685] [drm] Initialized
[ 4.098748] brd: module loaded
[ 4.107393] loop: module loaded
[ 4.110663] tegra_profiler: version: 1.139, samples/io: 47/27
[ 4.116553] tegra_profiler: auth: init
[ 4.121641] THERMAL EST: found 2 subdevs
[ 4.125858] THERMAL EST num_resources: 0
[ 4.129800] [THERMAL EST subdev 0]
[ 4.133215] [THERMAL EST subdev 1]
[ 4.137092] thermal thermal_zone5: Registering thermal zone thermal_zone5 for type thermal-fan-est
[ 4.146064] THERMAL EST: thz register success.
[ 4.150693] THERMAL EST: end of probe, return err: 0
[ 4.156947] hisi_sas: driver version v1.6
[ 4.165283] tegra-qspi 70410000.spi: Prod settings list not found
[ 4.172628] qspi_mtd spi32766.0: MX25U3235F (4096 Kbytes)
[ 4.178059] qspi_mtd spi32766.0: mtd .name = spi32766.0, .size = 0x400000 (4MiB) .erasesize = 0x00001000 (4KiB) .numeraseregions = 0
[ 4.193035] libphy: Fixed MDIO Bus: probed
[ 4.198217] tun: Universal TUN/TAP device driver, 1.6
[ 4.203302] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 4.210401] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[ 4.216260] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 4.222258] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
[ 4.229267] igb: Copyright (c) 2007-2014 Intel Corporation.
[ 4.234906] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k
[ 4.242747] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
[ 4.248729] Intel(R) 10GbE PCI Express Linux Network Driver - version 4.6.4
[ 4.255700] Copyright(c) 1999 - 2017 Intel Corporation.
[ 4.261780] r8168 0000:01:00.0: enabling device (0000 -> 0003)
[ 4.267669] r8168 Gigabit Ethernet driver 8.045.08-NAPI loaded
[ 4.287669] r8168 0000:01:00.0 (unnamed net_device) (uninitialized): Invalid ethernet address 00:00:00:00:00:00, trying device tree node
[ 4.300102] r8168 0000:01:00.0 (unnamed net_device) (uninitialized): Found valid ethernet address 00:04:4b:e6:53:41 from device tree
[ 4.312582] r8168: This product is covered by one or more of the following patents: US6,570,884, US6,115,776, and US6,327,625.
[ 4.324049] r8168 Copyright (C) 2017 Realtek NIC software team <nicfae@realtek.com>
[ 4.324049] This program comes with ABSOLUTELY NO WARRANTY; for details, please see <http://www.gnu.org/licenses/>.
[ 4.324049] This is free software, and you are welcome to redistribute it under certain conditions; see <http://www.gnu.org/licenses/>.
[ 4.355417] PPP generic driver version 2.4.2
[ 4.359904] PPP BSD Compression module registered
[ 4.364629] PPP Deflate Compression module registered
[ 4.369725] PPP MPPE Compression module registered
[ 4.374531] NET: Registered protocol family 24
[ 4.379052] usbcore: registered new interface driver r8152
[ 4.384596] usbcore: registered new interface driver asix
[ 4.390061] usbcore: registered new interface driver ax88179_178a
[ 4.396207] usbcore: registered new interface driver cdc_ether
[ 4.402081] usbcore: registered new interface driver net1080
[ 4.407789] usbcore: registered new interface driver cdc_subset
[ 4.413750] usbcore: registered new interface driver zaurus
[ 4.419389] usbcore: registered new interface driver cdc_ncm
[ 4.425219] VFIO - User Level meta-driver version: 0.3
[ 4.431607] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.438175] ehci-pci: EHCI PCI platform driver
[ 4.442680] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.448878] ohci-pci: OHCI PCI platform driver
[ 4.453373] ohci-platform: OHCI generic platform driver
[ 4.461121] tegra-xusb 70090000.xusb: USB2 port 0 has OTG_CAP
[ 4.467497] tegra-xusb-padctl 7009f000.xusb_padctl: enabled OTG on UTMI pad 0
[ 4.475829] tegra-xusb 70090000.xusb: extcon 0: ffffffc0f966b800 id
[ 4.484279] usbcore: registered new interface driver uas
[ 4.489658] tegra-xusb 70090000.xusb: Firmware timestamp: 2019-10-17 15:58:59 UTC, Version: 50.25 release
[ 4.489723] tegra-xusb 70090000.xusb: xHCI Host Controller
[ 4.489748] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 1
[ 4.490514] tegra-xusb 70090000.xusb: hcc params 0x0184f525 hci version 0x100 quirks 0x00050010
[ 4.490579] tegra-xusb 70090000.xusb: irq 61, io mem 0x70090000
[ 4.490873] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 4.490879] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.490883] usb usb1: Product: xHCI Host Controller
[ 4.490886] usb usb1: Manufacturer: Linux 4.9.140-tegra xhci-hcd
[ 4.490890] usb usb1: SerialNumber: 70090000.xusb
[ 4.491520] hub 1-0:1.0: USB hub found
[ 4.491561] hub 1-0:1.0: 5 ports detected
[ 4.492086] tegra-xusb 70090000.xusb: xHCI Host Controller
[ 4.492098] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 2
[ 4.492172] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 4.492320] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 4.492324] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.492328] usb usb2: Product: xHCI Host Controller
[ 4.492332] usb usb2: Manufacturer: Linux 4.9.140-tegra xhci-hcd
[ 4.492335] usb usb2: SerialNumber: 70090000.xusb
[ 4.492749] hub 2-0:1.0: USB hub found
[ 4.492780] hub 2-0:1.0: 4 ports detected
[ 4.595021] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 1
[ 4.630969] usbcore: registered new interface driver usb-storage
[ 4.637106] usbcore: registered new interface driver usbserial
[ 4.646355] tegra-xudc-new 700d0000.xudc: device count: 1
[ 4.653059] tegra-xudc-new 700d0000.xudc: USB charger detection disabled
[ 4.659800] tegra-xudc-new 700d0000.xudc: vbus state: 1
[ 4.665046] tegra-xudc-new 700d0000.xudc: device mode on: 0
[ 4.670655] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 0
[ 4.677369] tegra-xudc-new 700d0000.xudc: active: 0 => 1
[ 4.683369] mousedev: PS/2 mouse device common for all mice
[ 4.689057] usbcore: registered new interface driver xpad
[ 4.818977] usb 1-2: new high-speed USB device number 2 using tegra-xusb
[ 4.825890] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0
[ 4.835673] rtc rtc1: alarm rtc device
[ 4.839457] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1
[ 4.846631] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock
[ 4.853342] i2c /dev entries driver
[ 4.858566] imx219 6-0010: tegracam sensor driver:imx219_v2.0.6
[ 4.859342] usb 1-2: New USB device found, idVendor=0bda, idProduct=5411
[ 4.859347] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 4.859351] usb 1-2: Product: 4-Port USB 2.1 Hub
[ 4.859355] usb 1-2: Manufacturer: Generic
[ 4.860833] hub 1-2:1.0: USB hub found
[ 4.861921] hub 1-2:1.0: 4 ports detected
[ 4.918158] tegra-vii2c 546c0000.i2c: no acknowledge from address 0x10
[ 4.924782] imx219 6-0010: imx219_board_setup: error during i2c read probe (-121)
[ 4.932300] imx219 6-0010: board setup failed
[ 4.936771] imx219: probe of 6-0010 failed with error -121
[ 4.943269] max77620-power max77620-power: Event recorder REG_NVERC : 0x0
[ 4.952709] tegra_soctherm 700e2000.soctherm: pllx_offset tz:0 max:14, min:2
[ 4.959796] tegra_soctherm 700e2000.soctherm: pllx_offset tz:2 max:8, min:4
[ 4.967655] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[ 4.977003] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when cpu reaches 102500 mC
[ 4.985995] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when cpu reaches 100500 mC
[ 4.995066] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[ 5.004392] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when gpu reaches 103000 mC
[ 5.013359] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when gpu reaches 101000 mC
[ 5.022386] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[ 5.031707] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when pll reaches 127000 mC
[ 5.040670] tegra_soctherm 700e2000.soctherm: throttrip: pll: missing hot temperature
[ 5.048681] tegra_soctherm 700e2000.soctherm: failed to register sensor: -19
[ 5.056566] tegra_aotag tegra-aotag: Registering sensor 0
[ 5.062082] tegra_aotag tegra-aotag: Bound to TZ : ID 0
[ 5.067334] tegra_aotag tegra-aotag: Probe done [SUCCESS]:0
[ 5.074300] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[ 5.083653] tegra_dfll_action dfll-cdev-cap: Tegra DFLL 'cap cooling device' registered
[ 5.092042] tegra_dfll_action dfll-cdev-floor: Tegra DFLL 'floor cooling device' registered
[ 5.100842] parse_throttle_dt_data: Num cap clks = 6
[ 5.105822] parse_throttle_dt_data: clk=cclk_g type=2
[ 5.110895] parse_throttle_dt_data: clk=gpu type=4
[ 5.115741] parse_throttle_dt_data: clk=cap.throttle.c2bus type=0
[ 5.121864] parse_throttle_dt_data: clk=cap.throttle.c3bus type=0
[ 5.127982] parse_throttle_dt_data: clk=cap.throttle.sclk type=0
[ 5.133997] parse_throttle_dt_data: clk=emc type=3
[ 5.139201] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[ 5.148617] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[ 5.157948] usb 1-2.1: new low-speed USB device number 3 using tegra-xusb
[ 5.164955] tegra_throttle_probe: probe successful. #cdevs=4
[ 5.171383] FAN dev name: pwm-fan
[ 5.174787] FAN:gpio request success.
[ 5.178541] pwm_fan_driver pwm-fan: cap state:7, cap pwm:255
[ 5.184563] pwm_fan_driver pwm-fan: got pwm for fan. polarity is normal
[ 5.191445] pwm_fan_driver pwm-fan: fan tach request irq success
[ 5.197564] pwm_fan_driver pwm-fan: tach period: 1000
[ 5.202792] pwm_fan_driver pwm-fan: index 0: pwm=0, rpm=0, rru=40, rrd=40, state:2
[ 5.210446] pwm_fan_driver pwm-fan: index 1: pwm=80, rpm=1000, rru=2, rrd=2, state:2
[ 5.218266] pwm_fan_driver pwm-fan: index 2: pwm=120, rpm=2000, rru=1, rrd=1, state:2
[ 5.226169] pwm_fan_driver pwm-fan: index 3: pwm=160, rpm=3000, rru=1, rrd=1, state:2
[ 5.234053] usb 1-2.1: New USB device found, idVendor=040b, idProduct=2000
[ 5.234059] usb 1-2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 5.234063] usb 1-2.1: Product: USB Keyboard
[ 5.234066] usb 1-2.1: Manufacturer: Generic
[ 5.257171] pwm_fan_driver pwm-fan: index 4: pwm=255, rpm=4000, rru=1, rrd=1, state:3
[ 5.265015] pwm_fan_driver pwm-fan: index 5: pwm=255, rpm=5000, rru=1, rrd=1, state:3
[ 5.272856] pwm_fan_driver pwm-fan: index 6: pwm=255, rpm=6000, rru=1, rrd=1, state:3
[ 5.280696] pwm_fan_driver pwm-fan: index 7: pwm=255, rpm=7000, rru=1, rrd=1, state:4
[ 5.288530] pwm_fan_driver pwm-fan: index 8: pwm=255, rpm=10000, rru=1, rrd=1, state:4
[ 5.296454] pwm_fan_driver pwm-fan: index 9: pwm=255, rpm=11000, rru=1, rrd=1, state:4
[ 5.305140] tegra-wdt 60005100.watchdog: Tegra WDT enabled on probe. Timeout = 120 seconds.
[ 5.313856] tegra-wdt 60005100.watchdog: initialized (timeout = 120 sec, nowayout = 1)
[ 5.322696] device-mapper: uevent: version 1.0.3
[ 5.327359] usb 1-2.3: new low-speed USB device number 4 using tegra-xusb
[ 5.334692] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com
[ 5.348489] tegra210-cpufreq cpufreq: probe()...completed
[ 5.354751] sdhci: Secure Digital Host Controller Interface driver
[ 5.360987] sdhci: Copyright(c) Pierre Ossman
[ 5.365389] sdhci-pltfm: SDHCI platform and OF driver helper
[ 5.371631] sdhci-tegra sdhci-tegra.0: Got CD GPIO
[ 5.376849] sdhci-tegra sdhci-tegra.0: Client registration for eMC Successful
[ 5.384016] usb 1-2.3: New USB device found, idVendor=093a, idProduct=2510
[ 5.384020] usb 1-2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 5.384022] usb 1-2.3: Product: USB Optical Mouse
[ 5.384025] usb 1-2.3: Manufacturer: PixArt
[ 5.407354] sdhci-tegra sdhci-tegra.0: wakeup init done, cdirq 300
[ 5.417910] tegra-se 70012000.se: tegra_se_probe: complete
[ 5.423899] hidraw: raw HID events driver (C) Jiri Kosina
[ 5.433915] input: Generic USB Keyboard as /devices/70090000.xusb/usb1/1-2/1-2.1/1-2.1:1.0/0003:040B:2000.0001/input/input0
[ 5.459171] mmc0: SDHCI controller on sdhci-tegra.0 [sdhci-tegra.0] using ADMA 64-bit with 64 bit addr
[ 5.503485] hid-generic 0003:040B:2000.0001: input,hidraw0: USB HID v1.10 Keyboard [Generic USB Keyboard] on usb-70090000.xusb-2.1/input0
[ 5.521773] input: Generic USB Keyboard as /devices/70090000.xusb/usb1/1-2/1-2.1/1-2.1:1.1/0003:040B:2000.0002/input/input1
[ 5.536467] mmc0: new SDHC card at address 0001
[ 5.541315] mmcblk0: mmc0:0001 SD16G 29.8 GiB
[ 5.591566] hid-generic 0003:040B:2000.0002: input,hidraw1: USB HID v1.10 Mouse [Generic USB Keyboard] on usb-70090000.xusb-2.1/input1
[ 5.605983] input: PixArt USB Optical Mouse as /devices/70090000.xusb/usb1/1-2/1-2.3/1-2.3:1.0/0003:093A:2510.0003/input/input2
[ 5.617987] hid-generic 0003:093A:2510.0003: input,hidraw2: USB HID v1.11 Mouse [PixArt USB Optical Mouse] on usb-70090000.xusb-2.3/input0
[ 5.630499] usbcore: registered new interface driver usbhid
[ 5.636099] usbhid: USB HID core driver
[ 5.642075] tegra21x_actmon 6000c800.actmon: in actmon_register()...
[ 5.648666] tegra21x_actmon 6000c800.actmon: initialization Completed for the device mc_all
[ 5.658752] nvpmodel: initialized successfully
[ 5.664402] usbcore: registered new interface driver snd-usb-audio
[ 5.670656] No Device Node present for smmu client: snd-soc-dummy !!
[ 5.677024] platform snd-soc-dummy: No iommus property found in DT node, got swgids from fixup(101004000)
[ 5.687769] iommu: Adding device snd-soc-dummy to group 36
[ 5.694057] input: tegra-hda HDMI/DP,pcm=3 as /devices/70030000.hda/sound/card0/input3
[ 5.717037] OPE platform probe
[ 5.720183] OPE platform probe successful
[ 5.724238] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14
[ 5.731259] OPE platform probe
[ 5.734411] OPE platform probe successful
[ 5.764135] tegra-asoc: sound: ADMAIF1 <-> ADMAIF1 mapping ok
[ 5.770018] tegra-asoc: sound: ADMAIF2 <-> ADMAIF2 mapping ok
[ 5.775885] tegra-asoc: sound: ADMAIF3 <-> ADMAIF3 mapping ok
[ 5.781748] tegra-asoc: sound: ADMAIF4 <-> ADMAIF4 mapping ok
[ 5.787621] tegra-asoc: sound: ADMAIF5 <-> ADMAIF5 mapping ok
[ 5.793484] tegra-asoc: sound: ADMAIF6 <-> ADMAIF6 mapping ok
[ 5.799351] tegra-asoc: sound: ADMAIF7 <-> ADMAIF7 mapping ok
[ 5.805216] tegra-asoc: sound: ADMAIF8 <-> ADMAIF8 mapping ok
[ 5.811078] tegra-asoc: sound: ADMAIF9 <-> ADMAIF9 mapping ok
[ 5.816946] tegra-asoc: sound: ADMAIF10 <-> ADMAIF10 mapping ok
[ 5.834605] u32 classifier
[ 5.837331] Actions configured
[ 5.840800] Initializing XFRM netlink socket
[ 5.845778] NET: Registered protocol family 10
[ 5.850962] NET: Registered protocol family 17
[ 5.855422] NET: Registered protocol family 15
[ 5.859939] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 5.873031] Bluetooth: RFCOMM socket layer initialized
[ 5.878181] Bluetooth: RFCOMM ver 1.11
[ 5.881935] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 5.887856] Bluetooth: HIDP socket layer initialized
[ 5.892843] 9pnet: Installing 9P2000 support
[ 5.897146] Key type dns_resolver registered
[ 5.901822] Registered cp15_barrier emulation handler
[ 5.906928] Registered setend emulation handler
[ 5.913312] registered taskstats version 1
[ 5.917997] Adding domain ve2-pd to PM domain host1x-pd
[ 5.923474] Adding domain ve-pd to PM domain host1x-pd
[ 5.930618] isp 54600000.isp: initialized
[ 5.935675] isp 54680000.isp: initialized
[ 5.949778] last reset is due to power on reset
[ 5.954346] KERNEL: PMC reset status reg: 0x0
[ 5.958780] BL: PMC reset status reg: 0x0
[ 5.962791] BL: PMIC poweroff Event Recorder: 0x40
[ 5.968999] clk_cbus_recalc_rate: no gbus parent
[ 5.973637] clk_cbus_round_rate: no gbus parent
[ 5.978206] clk_cbus_round_rate: no gbus parent
[ 5.982741] clk_cbus_recalc_rate: no gbus parent
[ 5.987460] clk_cbus_recalc_rate: no gbus parent
[ 5.992098] clk_cbus_round_rate: no gbus parent
[ 5.996627] clk_cbus_round_rate: no gbus parent
[ 6.001156] clk_cbus_recalc_rate: no gbus parent
[ 6.005785] tegra_dvfs: GPU-cap: registered
[ 6.010032] tegra dvfs: vdd-cpu: nominal 1168mV, offset 708000uV, step 19200uV, scaling enabled
[ 6.018728] tegra dvfs: vdd-core: nominal 1075mV, offset 600000uV, step 12500uV, scaling enabled
[ 6.027506] tegra dvfs: vdd-gpu: nominal 1058mV, offset 708000uV, step 10000uV, scaling enabled
[ 6.037548] tegra_dvfs: vdd-gpu-vts: registered
[ 6.042749] tegra_core_action core_dvfs_cdev_floor: Tegra CORE DVFS 'floor cooling device' registered
[ 6.052577] tegra_core_action core_dvfs_cdev_cap: Tegra CORE DVFS 'cap cooling device' registered
[ 6.061976] input: gpio-keys as /devices/gpio-keys/input/input4
[ 6.101541] tegra_rtc 7000e000.rtc: setting system clock to 2000-01-01 01:00:20 UTC (946688420)
[ 6.111264] vi 54080000.vi: vi_probe: ++
[ 6.117718] vi 54080000.vi: initialized
[ 6.123531] vi 54080000.vi: subdev nvcsi--1 bound
[ 6.128453] mmcblk mmc0:0001: Card claimed for testing.
[ 6.134901] Disable partitions left on by BL
[ 6.139182] disb
[ 6.141232] bwmgr: missing cdev-type property
[ 6.145678] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[ 6.154988] DRAM derating cdev registered.
[ 6.160049] vdd-fan: disabling
[ 6.163119] vdd-usb-vbus: disabling
[ 6.166600] vdd-usb-vbus2: disabling
[ 6.170182] avdd-io-edp-1v05: disabling
[ 6.174160] ALSA device list:
[ 6.177131] #0: tegra-hda at 0x70038000 irq 83
[ 6.181748] #1: tegra-snd-t210ref-mobile-rt565x
[ 6.189572] Freeing unused kernel memory: 8576K
[ 6.214467] Root device found: mmcblk0p1
[ 6.219480] Found dev node: /dev/mmcblk0p1
[ 8.655590] tegra-xusb 70090000.xusb: Upgrade port 0 to USB3.0
[ 8.661421] tegra-xusb 70090000.xusb: Upgrade port 1 to USB3.0
[ 8.983947] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb
[ 9.022562] usb 2-1: New USB device found, idVendor=0bda, idProduct=0411
[ 9.029268] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 9.036398] usb 2-1: Product: 4-Port USB 3.1 Hub
[ 9.041014] usb 2-1: Manufacturer: Generic
[ 9.049744] hub 2-1:1.0: USB hub found
[ 9.056111] hub 2-1:1.0: 4 ports detected
[ 9.219018] usb 2-1: usb_suspend_both: status 0
[ 9.223658] usb usb2: usb_suspend_both: status 0
[ 65.367013] random: crng init done
[ 78.960571] EXT4-fs (mmcblk0p1): recovery complete
[ 79.058593] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)
[ 79.067454] Rootfs mounted over mmcblk0p1
[ 104.041021] Switching from initrd to actual rootfs
[ 329.797880] systemd[1]: System time before build time, advancing clock.
[ 351.419222] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 352.769051] cgroup: cgroup2: unknown option "nsdelegate"
[ 360.057513] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[ 360.079553] systemd[1]: Detected architecture arm64.
[ 363.071804] systemd[1]: No hostname configured.
[ 363.076380] systemd[1]: Set hostname to <localhost>.
[ 408.140015] systemd[1]: File /lib/systemd/system/systemd-journald.service:36 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling.
[ 408.157058] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.)
[ 450.744363] systemd[1]: Created slice System Slice.
[ 450.749668] systemd[1]: Listening on fsck to fsckd communication Socket.
[ 450.756507] systemd[1]: Reached target Slices.
[ 450.761162] systemd[1]: Listening on RPCbind Server Activation Socket.
[ 450.767978] systemd[1]: Listening on Journal Socket.
[ 450.775313] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[ 450.787066] systemd[1]: Starting Set console scheme...
[ 450.792596] systemd[1]: Listening on udev Kernel Socket.
[ 450.947080] systemd[1]: Listening on udev Control Socket.
[ 450.954780] systemd[1]: Starting Nameserver information manager...
[ 464.046267] systemd[1]: Starting Load Kernel Modules...
[ 464.051909] systemd[1]: Listening on Journal Socket (/dev/log).
[ 464.059940] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 483.374005] systemd[1]: Listening on Journal Audit Socket.
[ 483.379703] systemd[1]: Reached target Swap.
[ 483.386379] systemd[1]: Mounting Huge Pages File System...
[ 483.394346] systemd[1]: Mounting POSIX Message Queue File System...
[ 483.403102] systemd[1]: Starting Journal Service...
[ 483.410418] systemd[1]: Starting udev Coldplug all Devices...
[ 483.419067] systemd[1]: Mounting Kernel Debug File System...
[ 483.425061] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 483.434467] systemd[1]: Starting Remount Root and Kernel File Systems...
[ 483.444394] systemd[1]: Started Set console scheme.
[ 496.242179] systemd[1]: Started Create list of required static device nodes for the current kernel.
[ 496.253989] systemd[1]: Starting Create Static Device Nodes in /dev...
[ 510.601201] systemd[1]: Started Journal Service.
[ 588.629106] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null)
[ 610.549856] systemd-journald[1983]: Received request to flush runtime journal from PID 1
[ 1088.627061] INFO: task systemd-tmpfile:3630 blocked for more than 120 seconds.
[ 1088.634295] Not tainted 4.9.140-tegra #1
[ 1088.638770] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1088.646686] Kernel panic - not syncing: hung_task: blocked tasks
[ 1088.652682] CPU: 3 PID: 584 Comm: khungtaskd Not tainted 4.9.140-tegra #1
[ 1088.659455] Hardware name: NVIDIA Jetson Nano Developer Kit (DT)
[ 1088.665448] Call trace:
[ 1088.667888] [<ffffff800808bdb8>] dump_backtrace+0x0/0x198
[ 1088.673277] [<ffffff800808c37c>] show_stack+0x24/0x30
[ 1088.678318] [<ffffff800845d820>] dump_stack+0x98/0xc0
[ 1088.683361] [<ffffff80081c2198>] panic+0x11c/0x298
[ 1088.688143] [<ffffff8008181f90>] watchdog+0x300/0x3b8
[ 1088.693184] [<ffffff80080dbee4>] kthread+0xec/0xf0
[ 1088.697964] [<ffffff8008083850>] ret_from_fork+0x10/0x40
[ 1088.703265] SMP: stopping secondary CPUs
[ 1088.707230] Kernel Offset: disabled
[ 1088.710713] Memory Limit: none
[ 1088.719815] Rebooting in 5 seconds..
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment