Nano boot sequence after flash.sh executes

nano_flash_boot.txt

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2020.03.18 09:55:14 =~=~=~=~=~=~=~=~=~=~=~=
0023.092] Enabled early print
[0023.094] [L4T TegraBoot] (version 00.00.2018.01-l4t-1463e5a5)
[0023.100] Processing in recovery mode
[0023.103] A02 Bootrom Patch rev = 1023
[0023.107] Power-up reason: pmc por
[0023.110] Established communication link with host
[0024.111] NvTbootI2cWrite(): error code 0x00045100 Error while starting write transaction
[0024.119] NvTbootI2cDeviceRead(): error code 0x00045001 Error while sending the offset to slave
[0024.127] NvTbootI2c: Read failed for slave 0xac, offset 0x00 with error code 0x00045001
[0205.831] Odmdata from BCT: 0x00094000
[0205.835] DebugPort= 0x3
[0205.844] BoardId read from EEPROM/NCT: 3448
[0205.848] BoardID = 3448, SKU = 0x0
[0205.875] NvTbootInit_Porg: Setting GPIO_A6 for HDMI ...
[0205.880] max77620 setting MBLPD bit
[0205.884] No Battery Present
[0205.886] RamCode = 0
[0205.889] Platform has DDR4 type RAM
[0205.892] max77620 disabling SD1 Remote Sense
[0205.896] Setting DDR voltage to 1125mv
[0205.900] Serial Number of Pmic Max77663: 0x1727e5
[0205.908] Entering ramdump check
[0205.911] Get RamDumpCarveOut = 0x0
[0205.914] RamDumpCarveOut=0x0,  RamDumperFlag=0xe59ff3f8
[0205.920] Last reboot was clean, booting normally!
[0205.924] Sdram initialization is successful 
[0205.928] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000
[0205.935] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000
[0205.940] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000
[0205.946] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000
[0205.952] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000
[0205.958] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000
[0205.964] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000
[0205.970] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000
[0205.986] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000
[0205.992] Platform-DebugCarveout: 0
[0205.995] Downloaded BCT successfully
[0206.256] Downloaded Bootloader successfully
[0206.307] Downloaded rp1 successfully
[0206.335] MAX77620_GPIO5 configured
[0206.339] CPU power rail is up
[0206.341] CPU clock enabled
[0206.345] Performing RAM repair
[0206.348] Updating A64 Warmreset Address to 0x92c002e9
[0206.354] Enable APE clock/reset
[0206.358] Error in NvTbootGetTOSBinaryLength: 0x11 !
[0206.362] Loading Secure OS image failed. 
[0206.366] Set NvDecSticky Bits
[0206.370] GSC2 address ff53fffc value c0edbbcc
[0206.376] GSC MC Settings done
[0206.380] Next binary entry address: 0x92c00258 
[0206.385] BoardId: 3448
[0206.387] Overriding pmu board id with proc board id
[0206.392] Display board id is not available 
[0206.396] Starting CPU & Halting co-processor 

[0211.361] 
[0211.362] Debug Init done
[0211.366] Marked DTB cacheable
[0211.369] Bootloader DTB loaded at 0x83000400
[0211.373] DeviceTree Init done
[0211.386] Pinmux applied successfully
[0211.390] gicd_base: 0x50041000
[0211.394] gicc_base: 0x50042000
[0211.396] Interrupts Init done
[0211.401] Using base:0x60005090 & irq:208 for tick-timer
[0211.406] Using base:0x60005098 for delay-timer
[0211.410] platform_init_timer: DONE
[0211.414] Timer(tick) Init done
[0211.417] osc freq = 38400 khz
[0211.422] 
[0211.423] Welcome to L4T Cboot
[0211.426] 
[0211.427] Cboot Version: 00.00.2018.01-t210-40c3ff9c
[0211.432] calling constructors
[0211.435] initializing heap
[0211.437] initializing threads
[0211.440] initializing timers
[0211.443] creating bootstrap completion thread
[0211.448] top of bootstrap2()
[0211.451] CPU: ARM Cortex A57
[0211.453] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000
[0211.458] initializing platform
[0211.466] Manufacturer: MF = 0xc2, ID MSB = 0x25
[0211.470] ID LSB = 0x36, ID-CFI len = 194 bytes
[0211.475] Macronix QSPI chip present
[0211.478] SPI device register
[0211.481] init boot device
[0211.484] allocating memory for boot device(SPI)
[0211.488] registering boot device
[0211.498] sdmmc node status = okay
[0211.501] sdcard instance = 0
[0211.504] sdcard gpio handle 0x56
[0211.507] sdcard gpio pin 0xc9
[0211.510] sdcard gpio flags 0x0
[0211.513] vmmc-supply 0x99
[0211.516] Instance: 0
[0211.518] Allocating memory for context
[0211.521] enabling clock
[0211.524] sd card init
[0211.526] Check card present and stable
[0211.530] Send command 0
[0211.583] Send command 3
[0211.587] Set RCA for the card
[0211.590] Query card specific data by command 9
[0211.596] Parse CSD data
[0211.599] Send command 7
[0211.609] Calling sd device register
[0211.612] Init sdcard
[0211.615] Allocating memory for boot device
[0211.619] Registering user device
[0211.632] of_register: registering tegra_udc to of_hal
[0211.637] of_register: registering inv20628-driver to of_hal
[0211.643] of_register: registering ads1015-driver to of_hal
[0211.648] of_register: registering lp8557-bl-driver to of_hal
[0211.654] of_register: registering bq2419x_charger to of_hal
[0211.660] of_register: registering bq27441_fuel_gauge to of_hal
[0211.671] gpio framework initialized
[0211.674] of_register: registering tca9539_gpio to of_hal
[0211.680] of_register: registering tca9539_gpio to of_hal
[0211.685] of_register: registering i2c_bus_driver to of_hal
[0211.691] of_register: registering i2c_bus_driver to of_hal
[0211.696] of_register: registering i2c_bus_driver to of_hal
[0211.702] pmic framework initialized
[0211.705] of_register: registering max77620_pmic to of_hal
[0211.711] regulator framework initialized
[0211.715] of_register: registering tps65132_bl_driver to of_hal
[0211.721] initializing target
[0211.727] gpio_driver_register: register 'tegra_gpio_driver' driver
[0211.735] board ID = D78, board SKU = 0
[0211.738] Skipping Z3!
[0211.743] fixed regulator driver initialized
[0211.761] initializing OF layer
[0211.764] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0211.781] I2C Bus Init done
[0211.784] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0211.794] I2C Bus Init done
[0211.797] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0211.807] I2C Bus Init done
[0211.810] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0211.820] I2C Bus Init done
[0211.823] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0211.833] I2C Bus Init done
[0211.836] of_children_init: Ops found for compatible string maxim,max77620
[0211.846] max77620_init using irq 118
[0211.851] register 'maxim,max77620' pmic
[0211.855] gpio_driver_register: register 'max77620-gpio' driver
[0211.862] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0211.872] I2C Bus Init done
[0211.876] Applying platform configs
[0211.883] platform-init is not present. Skipping
[0211.887] calling apps_init()
[0211.907] Found 14 GPT partitions in "sd0"
[0211.911] Proceeding to flashing Server
[0211.915] usbdcd_reinit Initialize driver to use already enumerated device
[0211.922] nv3p_priv_usbf_open USB configuration success
[0211.958] Writing GPT partition
[0211.962] Erasing Boot device
[0211.964] device_write_gpt: Erasing boot device spiflash0
[0227.279] Erasing Storage Device
[0227.282] Writing protective mbr
[0227.296] Writing primary GPT
[0227.350] Writing secondary GPT
[0227.381] Found 14 GPT partitions in "sd0"
[0227.385] Writing NVC partition
[0237.400] partition NVC write successful.
[0237.405] Writing PT partition
[0237.654] partition PT write successful.
[0237.659] Writing NVC_R partition
[0247.691] partition NVC_R write successful.
[0247.696] Writing VER_b partition
[0247.970] partition VER_b write successful.
[0247.975] Writing VER partition
[0248.241] partition VER write successful.
[0248.247] Writing APP partition
[0699.896] partition APP write successful.
[0699.901] Writing TBC partition
[0699.957] partition TBC write successful.
[0699.961] Writing RP1 partition
[0700.067] partition RP1 write successful.
[0700.072] Writing EBT partition
[0700.172] partition EBT write successful.
[0700.177] Writing WB0 partition
[0700.227] partition WB0 write successful.
[0700.232] Writing BPF partition
[0700.271] partition BPF write successful.
[0700.276] Writing TOS partition
[0700.324] partition TOS write successful.
[0700.329] Writing DTB partition
[0700.397] partition DTB write successful.
[0700.402] Writing LNX partition
[0700.493] partition LNX write successful.
[0700.499] Writing EKS partition
[0700.538] partition EKS write successful.
[0700.543] Writing BMP partition
[0700.592] partition BMP write successful.
[0700.597] Writing RP4 partition
[0700.650] partition RP4 write successful.
[0700.661] Writing BCT partition
[0707.312] partition BCT write successful.
[0707.324] Change state to cold boot mode
[0707.328] Flushing data to stroage
[0000.157] [L4T TegraBoot] (version 00.00.2018.01-l4t-39a9dc3d)
[0000.163] Processing in cold boot mode Bootloader 2
[0000.167] A02 Bootrom Patch rev = 1023
[0000.171] Power-up reason: software reset
[0000.175] No Battery Present
[0000.177] pmic max77620 reset reason
[0000.181] pmic max77620 NVERC : 0x0
[0000.184] RamCode = 0
[0000.186] Platform has DDR4 type RAM
[0000.190] max77620 disabling SD1 Remote Sense
[0000.194] Setting DDR voltage to 1125mv
[0000.198] Serial Number of Pmic Max77663: 0x1727e5
[0000.206] Entering ramdump check
[0000.209] Get RamDumpCarveOut = 0x0
[0000.212] RamDumpCarveOut=0x0,  RamDumperFlag=0xe59ff3f8
[0000.217] Last reboot was clean, booting normally!
[0000.221] Sdram initialization is successful 
[0000.226] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000
[0000.232] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000
[0000.237] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000
[0000.243] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000
[0000.249] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000
[0000.255] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000
[0000.261] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000
[0000.267] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000
[0000.283] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000
[0000.289] Platform-DebugCarveout: 0
[0000.292] Nck Carveout Base=0x00000000ff080000 Size=0x00200000
[0000.298] Non secure mode, and RB not enabled.
[0000.375] Csd NumOfBlocks=62423040
[0000.380] Set High speed to 1
[0000.385] Using GPT Primary to query partitions
[0000.390] Loading Tboot-CPU binary
[0000.400] Verifying TBC in OdmNonSecureSBK mode
[0000.410] Bootloader load address is 0xa0000000, entry address is 0xa0000258
[0000.417] Bootloader downloaded successfully.
[0000.421] Downloaded Tboot-CPU binary to 0xa0000258
[0000.426] MAX77620_GPIO5 configured
[0000.429] CPU power rail is up
[0000.432] CPU clock enabled
[0000.436] Performing RAM repair
[0000.439] Updating A64 Warmreset Address to 0xa00002e9
[0000.444] Loading NvTbootBootloaderDTB
[0000.468] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode
[0000.534] Bootloader DTB Load Address: 0x83000000
[0000.538] Loading NvTbootKernelDTB
[0000.562] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode
[0000.628] Kernel DTB Load Address: 0x83100000
[0000.632] Loading cboot binary
[0000.662] Verifying EBT in OdmNonSecureSBK mode
[0000.704] Bootloader load address is 0x92c00000, entry address is 0x92c00258
[0000.711] Bootloader downloaded successfully.
[0000.728] Using BFS PT to query partitions 
[0000.732] Next binary entry address: 0x92c00258 
[0000.736] BoardId: 3448
[0000.741] Overriding pmu board id with proc board id
[0000.745] Display board id is not available 
[0000.774] Verifying SC7EntryFw in OdmNonSecureSBK mode
[0000.826] /bpmp deleted
[0000.828] SC7EntryFw header found loaded at 0xff700000
[0001.017] OVR2 PMIC
[0001.019] Bpmp FW successfully loaded
[0001.023] WB0 init successfully at 0xff780000
[0001.027] Set NvDecSticky Bits
[0001.031] GSC2 address ff53fffc value c0edbbcc
[0001.037] GSC MC Settings done
[0001.040] TOS Image length 53680
[0001.043]  Monitor size 53680
[0001.046]  OS size 0
[0001.053] Secure Os AES-CMAC Verification Success!
[0001.058] TOS image cipher info: plaintext
[0001.062] Loading and Validation of Secure OS Successful
[0001.078] SC7 Entry Firmware - 0xff700000, 0x4000
[0001.082] NvTbootPackSdramParams: start. 
[0001.087] NvTbootPackSdramParams: done. 
[0001.091] Tegraboot started after 85365 us
[0001.095] Basic modules init took 682933 us
[0001.099] Sec Bootdevice Read Time = 12 ms, Read Size = 65 KB
[0001.105] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB
[0001.110] Storage Device Read Time = 108 ms, Read Size = 2226 KB
[0001.116] Storage Device Write Time = 0 ms, Write Size = 0 KB
[0001.121] Next stage binary read took 24467 us
[0001.126] Carveout took -36130 us
[0001.129] CPU initialization took 361251 us
[0001.133] Total time taken by TegraBoot 1032521 us

[0001.138] Starting CPU & Halting co-processor 

64NOTICE:  BL31: v1.3(release):23b153a63
NOTICE:  BL31: Built : 22:39:57, Dec  9 2019
ERROR:   Error initializing runtime service trusty_fast
[0001.260] RamCode = 0
[0001.265] LPDDR4 Training: Read DT: Number of tables = 2
[0001.270] EMC Training (SRC-freq: 204000; DST-freq: 1600000)
[0001.282] EMC Training Successful
[0001.285] 408000 not found in DVFS table
[0001.292] RamCode = 0
[0001.295] DT Write: emc-table@204000 succeeded
[0001.301] DT Write: emc-table@1600000 succeeded
[0001.305] LPDDR4 Training: Write DT: Number of tables = 2
[0001.346] 
[0001.347] Debug Init done
[0001.349] Marked DTB cacheable
[0001.352] Bootloader DTB loaded at 0x83000000
[0001.357] Marked DTB cacheable
[0001.360] Kernel DTB loaded at 0x83100000
[0001.364] DeviceTree Init done
[0001.379] Pinmux applied successfully
[0001.384] gicd_base: 0x50041000
[0001.387] gicc_base: 0x50042000
[0001.390] Interrupts Init done
[0001.394] Using base:0x60005090 & irq:208 for tick-timer
[0001.399] Using base:0x60005098 for delay-timer
[0001.404] platform_init_timer: DONE
[0001.407] Timer(tick) Init done
[0001.411] osc freq = 38400 khz
[0001.415] 
[0001.416] Welcome to L4T Cboot
[0001.419] 
[0001.420] Cboot Version: 00.00.2018.01-t210-40c3ff9c
[0001.425] calling constructors
[0001.428] initializing heap
[0001.431] initializing threads
[0001.434] initializing timers
[0001.437] creating bootstrap completion thread
[0001.441] top of bootstrap2()
[0001.444] CPU: ARM Cortex A57
[0001.447] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000
[0001.452] initializing platform
[0001.459] Manufacturer: MF = 0xc2, ID MSB = 0x25
[0001.464] ID LSB = 0x36, ID-CFI len = 194 bytes
[0001.468] Macronix QSPI chip present
[0001.472] SPI device register
[0001.475] init boot device
[0001.477] allocating memory for boot device(SPI)
[0001.482] registering boot device
[0001.491] sdmmc node status = okay
[0001.494] sdcard instance = 0
[0001.497] sdcard gpio handle 0x56
[0001.501] sdcard gpio pin 0xc9
[0001.503] sdcard gpio flags 0x0
[0001.507] vmmc-supply 0x99
[0001.509] Instance: 0
[0001.511] Allocating memory for context
[0001.515] enabling clock
[0001.517] sd card init
[0001.520] Check card present and stable
[0001.523] Send command 0
[0001.540] Send command 3
[0001.544] Set RCA for the card
[0001.547] Query card specific data by command 9
[0001.554] Parse CSD data
[0001.556] Send command 7
[0001.566] Calling sd device register
[0001.570] Init sdcard
[0001.572] Allocating memory for boot device
[0001.576] Registering user device
[0001.589] Enable APE clock
[0001.592] Un-powergate APE partition
[0001.595] of_register: registering tegra_udc to of_hal
[0001.600] of_register: registering inv20628-driver to of_hal
[0001.606] of_register: registering ads1015-driver to of_hal
[0001.612] of_register: registering lp8557-bl-driver to of_hal
[0001.617] of_register: registering bq2419x_charger to of_hal
[0001.623] of_register: registering bq27441_fuel_gauge to of_hal
[0001.635] gpio framework initialized
[0001.638] of_register: registering tca9539_gpio to of_hal
[0001.643] of_register: registering tca9539_gpio to of_hal
[0001.649] of_register: registering i2c_bus_driver to of_hal
[0001.654] of_register: registering i2c_bus_driver to of_hal
[0001.660] of_register: registering i2c_bus_driver to of_hal
[0001.665] pmic framework initialized
[0001.669] of_register: registering max77620_pmic to of_hal
[0001.674] regulator framework initialized
[0001.678] of_register: registering tps65132_bl_driver to of_hal
[0001.684] initializing target
[0001.690] gpio_driver_register: register 'tegra_gpio_driver' driver
[0001.698] board ID = D78, board SKU = 0
[0001.702] Skipping Z3!
[0001.707] fixed regulator driver initialized
[0001.724] initializing OF layer
[0001.727] NCK carveout not present
[0001.730] Skipping dts_overrides
[0001.734] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.751] I2C Bus Init done
[0001.754] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.764] I2C Bus Init done
[0001.767] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.777] I2C Bus Init done
[0001.780] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.790] I2C Bus Init done
[0001.793] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.803] I2C Bus Init done
[0001.806] of_children_init: Ops found for compatible string maxim,max77620
[0001.816] max77620_init using irq 118
[0001.821] register 'maxim,max77620' pmic
[0001.825] gpio_driver_register: register 'max77620-gpio' driver
[0001.832] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.842] I2C Bus Init done
[0001.846] NCK carveout not present
[0001.856] Find /i2c@7000c000's alias i2c0
[0001.859] get eeprom at 1-a0, size 256, type 0
[0001.868] Find /i2c@7000c500's alias i2c2
[0001.872] get eeprom at 3-a0, size 256, type 0
[0001.877] get eeprom at 3-ae, size 256, type 0
[0001.881] pm_ids_update: Updating 1,a0, size 256, type 0
[0001.886] I2C slave not started
[0001.889] I2C write failed
[0001.892] Writing offset failed
[0001.895] eeprom_init: EEPROM read failed
[0001.899] pm_ids_update: eeprom init failed
[0001.903] pm_ids_update: Updating 3,a0, size 256, type 0
[0001.933] pm_ids_update: The pm board id is 3448-0000-200
[0001.940] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0001.948] pm_ids_update: pm id update successful
[0001.952] pm_ids_update: Updating 3,ae, size 256, type 0
[0001.982] pm_ids_update: The pm board id is 3449-0000-200
[0001.989] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0001.997] pm_ids_update: pm id update successful
[0002.027] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0002.033] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0002.041] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0002.047] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0002.056] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e6:53:41
[0002.062] Plugin Manager: Parse ODM data 0x00094000
[0002.072] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0   
[0002.094] Find /i2c@7000c000's alias i2c0
[0002.098] get eeprom at 1-a0, size 256, type 0
[0002.106] Find /i2c@7000c500's alias i2c2
[0002.110] get eeprom at 3-a0, size 256, type 0
[0002.115] get eeprom at 3-ae, size 256, type 0
[0002.119] pm_ids_update: Updating 1,a0, size 256, type 0
[0002.124] I2C slave not started
[0002.127] I2C write failed
[0002.130] Writing offset failed
[0002.133] eeprom_init: EEPROM read failed
[0002.137] pm_ids_update: eeprom init failed
[0002.141] pm_ids_update: Updating 3,a0, size 256, type 0
[0002.171] pm_ids_update: The pm board id is 3448-0000-200
[0002.178] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0002.185] pm_ids_update: pm id update successful
[0002.189] pm_ids_update: Updating 3,ae, size 256, type 0
[0002.219] pm_ids_update: The pm board id is 3449-0000-200
[0002.226] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0002.233] pm_ids_update: pm id update successful
[0002.263] Add serial number:1422419088143 as DT property
[0002.271] Applying platform configs
[0002.278] platform-init is not present. Skipping
[0002.282] calling apps_init()
[0002.302] Found 14 GPT partitions in "sd0"
[0002.306] Proceeding to Cold Boot
[0002.309] starting app android_boot_app
[0002.313] Device state: unlocked
[0002.316] display console init
[0002.325] could not find regulator
[0002.348] hdmi cable not connected
[0002.351] is_hdmi_needed: HDMI not connected, returning falDT entry for leds-pwm not found
s[0002.363] e
[0002.364] hdmi is not connected
[0002.367] sor0 is not supported
[0002.370] display_console_init: no valid display out_type
[0002.379] subnode volume_up is not found !
[0002.383] subnode back is not found !
[0002.386] subnode volume_down is not found !
[0002.390] subnode menu is not found !
[0002.394] Gpio keyboard init success
[0002.438] found decompressor handler: lz4-legacy
[0002.452] decompressing blob (type 1)...
[0002.486] display_resolution: No display init
[0002.490] Failed to retrieve display resolution
[0002.494] Could not load/initialize BMP blob...ignoring
[0002.545] decompressor handler not found
[0002.549] load_firmware_blob: Firmware blob loaded, entries=2
[0002.555] -------> se_aes_verify_sbk_clear: 747
[0002.559] se_aes_verify_sbk_clear: Error
[0002.563] bl_battery_charging: connected to external power supply
[0002.571] xusb is supported
[0002.577] error while finding nvidia,portmap
[0003.081] xusb blob version 0 size 124416
[0003.085] firmware size 124416
[0003.090] Firmware timestamp: 0x5da88fc3, Version: 50.25 release
[0003.097] xhci0: 64 bytes context size, 32-bit DMA
[0003.137] usbus0: 5.0Gbps Super Speed USB v3.0
[0003.157] uhub0: <Nvidia XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
[0003.807] uhub0: 9 ports with 9 removable, self powered
[0004.807] failed to get HID devices
[0004.810] failed to init xhci or no usb device attached
[0004.818] display_console_ioctl: No display init
[0004.822] switch_backlight failed
[0004.828] device_query_partition_size: failed to open partition sd0:MSC !
[0004.835] MSC Partition not found
[0004.841] device_query_partition_size: failed to open partition sd0:USP !
[0004.848] USP partition read failed!
[0004.852] blob_init: blob-partition USP header read failed
[0004.857] android_boot Unable to update recovery partition
[0004.863] kfs_getpartname: name = LNX
[0004.866] Loading kernel from LNX
[0004.964] load kernel from storage
[0004.976] decompressor handler not found
[0005.033] Successfully loaded kernel and ramdisk images
[0005.040] display_resolution: No display init
[0005.044] Failed to retrieve display resolution
[0005.048] bmp blob is not loaded and initialized
[0005.053] Failed to display boot-logo
[0005.057] NCK carveout not present
[0005.060] Skipping dts_overrides
[0005.063] NCK carveout not present
[0005.073] Find /i2c@7000c000's alias i2c0
[0005.077] get eeprom at 1-a0, size 256, type 0
[0005.086] Find /i2c@7000c500's alias i2c2
[0005.090] get eeprom at 3-a0, size 256, type 0
[0005.094] get eeprom at 3-ae, size 256, type 0
[0005.098] pm_ids_update: Updating 1,a0, size 256, type 0
[0005.104] I2C slave not started
[0005.107] I2C write failed
[0005.109] Writing offset failed
[0005.112] eeprom_init: EEPROM read failed
[0005.116] pm_ids_update: eeprom init failed
[0005.120] pm_ids_update: Updating 3,a0, size 256, type 0
[0005.151] pm_ids_update: The pm board id is 3448-0000-200
[0005.157] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0005.165] pm_ids_update: pm id update successful
[0005.170] pm_ids_update: Updating 3,ae, size 256, type 0
[0005.200] pm_ids_update: The pm board id is 3449-0000-200
[0005.206] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0005.214] pm_ids_update: pm id update successful
[0005.245] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0005.250] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0005.259] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0005.265] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0005.273] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e6:53:41
[0005.280] Plugin Manager: Parse ODM data 0x00094000
[0005.290] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0   
[0005.305] Add serial number:1422419088143 as DT property
[0005.314] "bpmp" doesn't exist, creating 
[0005.319] Updated bpmp info to DTB
[0005.324] Updated initrd info to DTB
[0005.327] "proc-board" doesn't exist, creating 
[0005.333] Updated board info to DTB
[0005.336] "pmu-board" doesn't exist, creating 
[0005.342] Updated board info to DTB
[0005.345] "display-board" doesn't exist, creating 
[0005.351] Updated board info to DTB
[0005.354] "reset" doesn't exist, creating 
[0005.359] Updated reset info to DTB
[0005.362] display_console_ioctl: No display init
[0005.367] display_console_ioctl: No display init
[0005.371] display_console_ioctl: No display init
[0005.376] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 
[0005.410] DTB cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0   
[0005.422] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 
[0005.435] Updated bootarg info to DTB
[0005.439] Adding uuid 00000001644495821c00000011fd8280 to DT
[0005.445] Adding eks info 0 to DT
[0005.450] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7
[0005.456] Updated memory info to DTB
[0005.462] Updated system-lp0-disable info to DTB
[0005.470] set vdd_core voltage to 1075 mv
[0005.474] setting 'vdd-core' regulator to 1075000 micro volts
[0005.497] Found secure-pmc; disable BPMP


U-Boot 2016.07-g0536cf2a27 (Dec 09 2019 - 22:40:32 -0800)

TEGRA210
Model: NVIDIA P3450-Porg
Board: NVIDIA P3450-PORG
DRAM:  4 GiB
MMC:   Tegra SD/MMC: 0, Tegra SD/MMC: 1
SF: Detected MX25U3235F with page size 256 Bytes, erase size 4 KiB, total 4 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Hit any key to stop autoboot:  1  0 
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/extlinux.conf
728 bytes read in 174 ms (3.9 KiB/s)
1:primary kernel
Retrieving file: /boot/initrd
5487751 bytes read in 542 ms (9.7 MiB/s)
Retrieving file: /boot/Image
34191368 bytes read in 2934 ms (11.1 MiB/s)
append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000  root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0    root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 
## Flattened Device Tree blob at 83100000
   Booting using the fdt blob at 0x83100000
   reserving fdt memory region: addr=80000000 size=20000
   Using Device Tree in place at 0000000083100000, end 00000000831776f0

Starting kernel ...

<hit enter to activate fiq debugger>
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.9.140-tegra (buildbrain@mobile-u64-2713) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Mon Dec 9 22:47:42 PST 2019
[    0.000000] Boot CPU: AArch64 Processor [411fd071]
[    0.000000] OF: fdt:memory scan node memory@80000000, reg size 48,
[    0.000000] OF: fdt: - 80000000 ,  7ee00000
[    0.000000] OF: fdt: - 100000000 ,  7f200000
[    0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB
[    0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB
[    0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB
[    0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB
[    0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout
[    0.000000] OF: reserved mem: initialized node iram-carveout, compatible id nvidia,iram-carveout
[    0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops
[    0.000000] cma: Reserved 64 MiB at 0x00000000fac00000
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.1
[    0.000000] percpu: Embedded 25 pages/cpu @ffffffc0fefb1000 s61592 r8192 d32616 u102400
[    0.000000] CPU features: enabling workaround for ARM erratum 832075
[    0.000000] Speculative Store Bypass Disable mitigation not required
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 1023544
[    0.000000] Kernel command line: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000  root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0    root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 
[    0.000000] log_buf_len individual max cpu contribution: 32768 bytes
[    0.000000] log_buf_len total cpu_extra contributions: 98304 bytes
[    0.000000] log_buf_len min size: 32768 bytes
[    0.000000] log_buf_len: 131072 bytes
[    0.000000] early log buf free: 29504(90%)
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.000000] Memory: 3570416K/4159488K available (15230K kernel code, 2926K rwdata, 6620K rodata, 8576K init, 609K bss, 113936K reserved, 475136K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)
[    0.000000]     vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000   (   250 GB)
[    0.000000]       .text : 0xffffff8008080000 - 0xffffff8008f60000   ( 15232 KB)
[    0.000000]     .rodata : 0xffffff8008f60000 - 0xffffff80095e0000   (  6656 KB)
[    0.000000]       .init : 0xffffff80095e0000 - 0xffffff8009e40000   (  8576 KB)
[    0.000000]       .data : 0xffffff8009e40000 - 0xffffff800a11b808   (  2927 KB)
[    0.000000]        .bss : 0xffffff800a11b808 - 0xffffff800a1b3dbc   (   610 KB)
[    0.000000]     fixed   : 0xffffffbefe7fd000 - 0xffffffbefec00000   (  4108 KB)
[    0.000000]     PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000   (    16 MB)
[    0.000000]     vmemmap : 0xffffffbf00000000 - 0xffffffc000000000   (     4 GB maximum)
[    0.000000]               0xffffffbf00000000 - 0xffffffbf03fc8000   (    63 MB actual)
[    0.000000]     memory  : 0xffffffc000000000 - 0xffffffc0ff200000   (  4082 MB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] Build-time adjustment of leaf fanout to 64.
[    0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[    0.000000] NR_IRQS:64 nr_irqs:64 0
[    0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller
[    0.000000] t210 clock and reset probe
[    0.000000] tegra-pmc: get_secure_pmc_setting: done secure_pmc=1
[    0.000000] clk_cbus_recalc_rate: no gbus parent
[    0.000000] clk_cbus_recalc_rate: no gbus parent
[    0.000000] clk_cbus_recalc_rate: no gbus parent
[    0.000000] clk_cbus_recalc_rate: no gbus parent
[    0.000000] clk_cbus_recalc_rate: no gbus parent
[    0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[    0.000005] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[    0.001715] Console: colour dummy device 80x25
[    0.002556] console [tty0] enabled
[    0.002583] kmemleak: Kernel memory leak detector disabled
[    0.002614] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800)
[    0.002644] pid_max: default: 32768 minimum: 301
[    0.003099] Security Framework initialized
[    0.003333] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.003354] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.004561] ftrace: allocating 47001 entries in 184 pages
[    0.176487] ASID allocator initialised with 65536 entries
[    0.215731] tegra-id: chipid=22117.
[    0.215776] tegra-id: opt_subrevision=0.
[    0.215805] Tegra Speedo/IDDQ fuse revision 4
[    0.215820] Tegra: CPU Speedo ID 9, SoC Speedo ID 0, GPU Speedo ID 2
[    0.215837] Tegra: CPU Process ID 0, SoC Process ID 1, GPU Process ID 0
[    0.215852] Tegra: CPU Speedo Value 2084, SoC Speedo Value 1976, GPU Speedo Value 2075
[    0.215872] Tegra: CPU IDDQ Value 1872, SoC IDDQ Value 1980, GPU IDDQ Value 2430
[    0.215906] Tegra Revision: A02 SKU: 0x8f CPU Process: 0 SoC Process: 1
[    0.215931] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0000-p3449-0000-a02.dts
[    0.215966] DTB Build time: Dec  9 2019 22:51:54
[    0.265031] CPU1: Booted secondary processor [411fd071]
[    0.296970] CPU2: Booted secondary processor [411fd071]
[    0.328935] CPU3: Booted secondary processor [411fd071]
[    0.329024] Brought up 4 CPUs
[    0.329087] SMP: Total of 4 processors activated.
[    0.329105] CPU features: detected feature: 32-bit EL0 Support
[    0.329385] CPU: All CPU(s) started at EL2
[    0.329415] alternatives: patching kernel code
[    0.337493] devtmpfs: initialized
[    0.374702] Initilizing CustomIPI irq domain
[    0.375120] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.375163] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.385636] pinctrl core: initialized pinctrl subsystem
[    0.386319] OS set in device tree is not L4T.
[    0.386728] regulator-dummy: no parameters
[    0.387028] Initializing plugin-manager
[    0.387148] Plugin module not found
[    0.387393] node /plugin-manager/fragement@0 match with board >=3448-0000-100
[    0.387952] node /plugin-manager/fragment@1 match with board >=3448-0000-101
[    0.388848] node /plugin-manager/fragment@5 match with board 3449-0000-200
[    0.389368] node /plugin-manager/fragement@6 match with odm-data enable-tegra-wdt
[    0.389819] node /plugin-manager/fragement@8 match with odm-data enable-tegra-wdt
[    0.390232] node /plugin-manager/fragement@9 match with board <3448-0000-300
[    0.394923] NET: Registered protocol family 16
[    0.396223] pstore: using zlib compression
[    0.396892] console [pstore-1] enabled
[    0.396910] pstore: Registered ramoops as persistent store backend
[    0.396929] ramoops: attached 0x200000@0xb0000000, ecc: 0/0
[    0.413051] cpuidle: using governor menu
[    0.417245] tegra_smmu 70019000.iommu: Loaded Tegra IOMMU driver
[    0.418828] vdso: 2 pages (1 code @ ffffff8008f67000, 1 data @ ffffff8009e44000)
[    0.418874] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.421487] atomic_pool_init():622: DMA: preallocated 1024 KiB pool for atomic allocations
[    0.424162] tegra_powergate_init: DONE
[    0.424200] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0000-p3449-0000-a02.dts
[    0.424238] DTB Build time: Dec  9 2019 22:51:54
[    0.426103] Tegra reboot handler registered.
[    0.430623] iommu: Adding device tegra-carveouts to group 0
[    0.430794] platform tegra-carveouts: domain=ffffffc0f9baa318 allocates as[0]=ffffffc0f9bdc0a8
[    0.431174] iommu: Adding device smmu_test to group 1
[    0.431240] platform smmu_test: domain=ffffffc0f9baa558 allocates as[0]=ffffffc0f9bdc110
[    0.432059] mc: mapped MMIO address: 0xffffff800802e000 -> 0x70019000
[    0.432148] mc: mapped MMIO address: 0xffffff8008065000 -> 0x7001c000
[    0.432215] mc: mapped MMIO address: 0xffffff8008079000 -> 0x7001d000
[    0.432239] nv-tegra-mc 70019000.mc: No mssnvlink node
[    0.432275] mc-err: mcerr ops are set to t21x
[    0.441943] iommu: Adding device 70090000.xusb to group 2
[    0.442282] iommu: Adding device 70006000.serial to group 3
[    0.442358] platform 70006000.serial: domain=ffffffc0f942ec18 allocates as[0]=ffffffc0f9bdc178
[    0.442792] iommu: Adding device 70006040.serial to group 4
[    0.443056] iommu: Adding device 70006200.serial to group 5
[    0.443265] iommu: Adding device sound to group 6
[    0.443333] platform sound: domain=ffffffc0f94aa198 allocates as[0]=ffffffc0f9bdc1e0
[    0.443912] iommu: Adding device 7000d400.spi to group 7
[    0.444195] iommu: Adding device 7000d600.spi to group 8
[    0.444525] iommu: Adding device 70410000.spi to group 9
[    0.444839] iommu: Adding device 50000000.host1x to group 10
[    0.445174] iommu: Adding device 54080000.vi to group 11
[    0.445604] iommu: Adding device 54600000.isp to group 12
[    0.445891] iommu: Adding device 54680000.isp to group 13
[    0.446188] iommu: Adding device tegradc.0 to group 14
[    0.446253] platform tegradc.0: domain=ffffffc0f94b60d8 allocates as[0]=ffffffc0f9bdc248
[    0.446791] platform tegradc.0: IOVA linear map 0x00000000d7000000(19000000)
[    0.447120] iommu: Adding device tegradc.1 to group 15
[    0.447182] platform tegradc.1: domain=ffffffc0f94b6318 allocates as[0]=ffffffc0f9bdc2b0
[    0.447706] platform tegradc.1: IOVA linear map 0x00000000d7000000(19000000)
[    0.447990] iommu: Adding device 54340000.vic to group 16
[    0.448210] iommu: Adding device 544c0000.nvenc to group 17
[    0.448427] iommu: Adding device 54500000.tsec to group 18
[    0.448643] iommu: Adding device 54100000.tsecb to group 19
[    0.448853] iommu: Adding device 54480000.nvdec to group 20
[    0.449083] iommu: Adding device 54380000.nvjpg to group 21
[    0.450168] iommu: Adding device 546c0000.i2c to group 22
[    0.450511] iommu: Adding device 57000000.gpu to group 23
[    0.450585] platform 57000000.gpu: domain=ffffffc0f94c1318 allocates as[0]=ffffffc0f9bdc318
[    0.450662] platform 57000000.gpu: domain=ffffffc0f94c1318 allocates as[1]=ffffffc0f9bdc380
[    0.450722] platform 57000000.gpu: domain=ffffffc0f94c1318 allocates as[2]=ffffffc0f9bdc3e8
[    0.450775] platform 57000000.gpu: domain=ffffffc0f94c1318 allocates as[3]=ffffffc0f9bdc450
[    0.451648] tegra-pmc 7000e400.pmc: i2c-thermtrip node not found, emergency thermal reset disabled.
[    0.451687] tegra-pmc 7000e400.pmc: scratch reg offset dts data not present
[    0.451715] tegra-pmc: ### PMC reset source: TEGRA_SOFTWARE_RESET
[    0.451736] tegra-pmc: ### PMC reset level: TEGRA_RESET_LEVEL_WARM
[    0.451754] tegra-pmc: ### PMC reset status reg: 0x3
[    0.501225] padctrl padctrl.0: Pad control driver tegra-pmc-padctrl registered
[    0.501262] tegra-pmc: Clear bootloader IO dpd settings
[    0.501299] tegra-pmc 7000e400.pmc: IO padctrl driver initialized
[    0.501379] tegra-pmc 7000e400.pmc: PMC: Successfully configure bootrom reset commands
[    0.501689] iommu: Adding device 70012000.se to group 24
[    0.502546] iommu: Adding device 7000c000.i2c to group 25
[    0.502868] iommu: Adding device 7000c400.i2c to group 26
[    0.503189] iommu: Adding device 7000c500.i2c to group 27
[    0.503520] iommu: Adding device 7000c700.i2c to group 28
[    0.503838] iommu: Adding device 7000d000.i2c to group 29
[    0.504162] iommu: Adding device 7000d100.i2c to group 30
[    0.504540] iommu: Adding device sdhci-tegra.0 to group 31
[    0.504615] platform sdhci-tegra.0: domain=ffffffc0f955c498 allocates as[0]=ffffffc0f9bdc4b8
[    0.505727] iommu: Adding device 700d0000.xudc to group 32
[    0.509921] vdd-ac-bat: 5000 mV 
[    0.510425] vdd-5v0-sys: 5000 mV 
[    0.511635] vdd-5v0-hdmi: supplied by vdd-5v0-sys
[    0.511697] vdd-5v0-hdmi: 5000 mV 
[    0.512210] vdd-1v8-sys: 1800 mV 
[    0.512770] vdd-fan: supplied by vdd-5v0-sys
[    0.512826] vdd-fan: 5000 mV 
[    0.513310] vdd-usb-vbus: supplied by vdd-5v0-sys
[    0.513362] vdd-usb-vbus: 5000 mV 
[    0.514043] vdd-usb-vbus2: 5000 mV 
[    0.545920] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.548283] gpio gpiochip0: gpio-line-names specifies 240 line names but there are 256 lines on the chip
[    0.549785] GPIO line 151 (camera-control-output-low) hogged as output/low
[    0.549826] GPIO line 152 (camera-control-output-low) hogged as output/low
[    0.550180] gpiochip_setup_dev: registered GPIOs 0 to 255 on device: gpiochip0 (tegra-gpio)
[    0.557959] eventlib_kernel: keventlib is initialized, test id: 0
[    0.558328] SCSI subsystem initialized
[    0.558830] usbcore: registered new interface driver usbfs
[    0.558902] usbcore: registered new interface driver hub
[    0.558990] usbcore: registered new device driver usb
[    0.562897] max77620 4-003c: PMIC Version OTP:0x35 and ES:0x8
[    0.568343] vdd-core: 600 <--> 1162 mV at 1075 mV 
[    0.568523] random: fast init done
[    0.569411] vdd-ddr-1v1: Bringing 1125000uV into 1150000-1150000uV
[    0.572236] vdd-ddr-1v1: 1150 mV 
[    0.576230] vdd-pre-reg-1v35: 1350 mV 
[    0.580243] vdd-1v8: 1800 mV 
[    0.584228] avdd-sys-1v2: 1200 mV 
[    0.588228] vdd-pex-1v0: 1050 mV 
[    0.588944] vddio-sdmmc-ap: 1800 <--> 3300 mV at 3300 mV 
[    0.589514] max77620-ldo3: at 3100 mV 
[    0.592233] vdd-rtc: 850 <--> 1100 mV at 1000 mV 
[    0.592786] max77620-ldo5: at 3100 mV 
[    0.593347] max77620-ldo6: at 2800 mV 
[    0.596236] avdd-1v05-pll: 1050 mV 
[    0.600228] avdd-io-hdmi-dp: 1050 mV 
[    0.602844] GPIO line 505 (spmic-default-output-high) hogged as output/high
[    0.603171] gpiochip_setup_dev: registered GPIOs 504 to 511 on device: gpiochip1 (max77620-gpio)
[    0.603486] max77620 4-003c: max77620 probe successful
[    0.606277] media: Linux media interface: v0.10
[    0.606349] Linux video capture interface: v2.00
[    0.607283] pps_core: LinuxPPS API ver. 1 registered
[    0.607308] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.607350] PTP clock support registered
[    0.611099] tegra_fiq_debugger_init: found FIQ source (IRQ 98)
[    0.617395] tegra210-emc 7001b000.external-memory-controller: validated EMC DFS table
[    0.618218] Advanced Linux Sound Architecture Driver Initialized.
[    0.618871] Bluetooth: Core ver 2.22
[    0.618949] NET: Registered protocol family 31
[    0.618968] Bluetooth: HCI device and connection manager initialized
[    0.618997] Bluetooth: HCI socket layer initialized
[    0.619023] Bluetooth: L2CAP socket layer initialized
[    0.619059] Bluetooth: SCO socket layer initialized
[    0.620810] tegra210_dvfs: no clock found for sdmmc2_ddr
[    0.620849] tegra210_dvfs: no clock found for sdmmc4_ddr
[    0.620908] tegra210_dvfs: no clock found for sdmmc1_ddr
[    0.620935] tegra210_dvfs: no clock found for sdmmc3_ddr
[    0.624079] tegra_dvfs: Unable to get vdd-cpu rail for step info, defering probe
[    0.625320] vdd-3v3-sys: supplied by vdd-5v0-sys
[    0.625426] vdd-3v3-sys: 3300 mV 
[    0.625713] vdd-1v8-sys: supplied by vdd-3v3-sys
[    0.628293] vdd-usb-vbus2: supplied by vdd-3v3-sys
[    0.628763] vdd-3v3-sd: supplied by vdd-3v3-sys
[    0.628815] vdd-3v3-sd: 3300 mV 
[    0.629912] avdd-io-edp-1v05: supplied by avdd-1v05-pll
[    0.629969] avdd-io-edp-1v05: 1050 mV 
[    0.630442] vdd-usb-hub-en: supplied by vdd-1v8-sys
[    0.630497] vdd-usb-hub-en: 5000 mV 
[    0.631861] camchar: rtcpu character device driver loaded
[    0.632629] extcon-gpio-states extcon:extcon@1: Cable state:1, cable id:1
[    0.634109] clocksource: Switched to clocksource arch_sys_counter
[    0.673745] VFS: Disk quotas dquot_6.6.0
[    0.673908] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.674478] nvmap_heap_init: nvmap_heap_init: created heap block cache
[    0.674894] dma_declare_coherent_resizable_cma_memory:324: resizable heap=vpr, base=0x00000000d7000000, size=0x19000000
[    0.674940]  dma-vpr: heap size is not multiple of cma_chunk_size heap_info->num_chunks (13) rem_chunk_size(0x1000000)
[    0.675216] cma: enabled page replacement for spfn=d7000, epfn=f0000
[    0.675244] dma_declare_coherent_resizable_cma_memory:373: resizable cma heap=vpr create successful
[    0.675275] tegra-carveouts tegra-carveouts: assigned reserved memory node vpr-carveout
[    0.675327] tegra-carveouts tegra-carveouts: iram :dma coherent mem declare 0x0000000040001000,258048
[    0.675355] tegra-carveouts tegra-carveouts: assigned reserved memory node iram-carveout
[    0.675387] nvmap: nvmap_select_cache_ops() nvmap cache ops set to set/ways
[    0.675410] nvmap_page_pool_init: Total RAM pages: 1011388
[    0.675428] nvmap_page_pool_init: nvmap page pool size: 126423 pages (493 MB)
[    0.675688] nvmap_background_zero_thread: PP zeroing thread starting.
[    0.675939] misc nvmap: created heap iram base 0x0000000040001000 size (252KiB)
[    0.676881] misc nvmap: created heap vpr base 0x00000000d7000000 size (409600KiB)
[    0.685015] thermal thermal_zone0: Registering thermal zone thermal_zone0 for type AO-therm
[    0.685466] thermal thermal_zone1: Registering thermal zone thermal_zone1 for type CPU-therm
[    0.685730] thermal thermal_zone2: Registering thermal zone thermal_zone2 for type GPU-therm
[    0.685959] thermal thermal_zone3: Registering thermal zone thermal_zone3 for type PLL-therm
[    0.686185] thermal thermal_zone4: Registering thermal zone thermal_zone4 for type PMIC-Die
[    0.686478] pre_t19x_iso_plat_init(): iso emc max clk=1600000KHz
[    0.686500] pre_t19x_iso_plat_init(): max_iso_bw=11520000KB
[    0.686959] NET: Registered protocol family 2
[    0.688021] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[    0.688259] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[    0.688775] TCP: Hash tables configured (established 32768 bind 32768)
[    0.688937] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    0.689035] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    0.689455] NET: Registered protocol family 1
[    0.690309] RPC: Registered named UNIX socket transport module.
[    0.690338] RPC: Registered udp transport module.
[    0.690355] RPC: Registered tcp transport module.
[    0.690372] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.690624] Trying to unpack rootfs image as initramfs...
[    0.921965] Freeing initrd memory: 5356K
[    0.931947] host1x 50000000.host1x: initialized
[    0.933769] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[    0.937057] audit: initializing netlink subsys (disabled)
[    0.937149] audit: type=2000 audit(0.787:1): initialized
[    0.937910] workingset: timestamp_bits=46 max_order=20 bucket_order=0
[    0.947919] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.949426] ntfs: driver 2.1.32 [Flags: R/W].
[    0.950295] 9p: Installing v9fs 9p2000 file system support
[    0.953520] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 240)
[    0.953688] io scheduler noop registered
[    0.954008] io scheduler cfq registered (default)
[    0.956724] gic 702f9000.agic: GIC IRQ controller registered
[    0.959784] iommu: Adding device 702ef000.adsp to group 33
[    0.968686] iommu: Adding device aconnect@702c0000:adsp_audio to group 34
[    0.968862] tegra-aconnect aconnect@702c0000: Tegra ACONNECT bus registered
[    0.969477] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_SKU_CALIB_0 = 0x8229413
[    0.969509] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_USB_CALIB_EXT_0 = 0x4
[    0.971202] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.0, lane = usb2-0, function = xusb
[    0.971342] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.1, lane = usb2-1, function = xusb
[    0.971458] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.2, lane = usb2-2, function = xusb
[    0.971665] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.3, lane = pcie-0, function = pcie-x1
[    0.971774] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.4, lane = pcie-1, function = pcie-x4
[    0.971885] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.5, lane = pcie-2, function = pcie-x4
[    0.971990] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.6, lane = pcie-3, function = pcie-x4
[    0.972101] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.7, lane = pcie-4, function = pcie-x4
[    0.972213] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.8, lane = pcie-5, function = xusb
[    0.972328] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.9, lane = pcie-6, function = xusb
[    0.978973] tegra-pwm 7000a000.pwm: PWM clk cannot sleep in ops
[    0.980807] tegra-dfll-pwm 70110000.pwm: DFLL pwm-rate: 12800000
[    0.982771] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration
[    0.984077] tegra-pcie 1003000.pcie: PCIE: Enable power rails
[    0.984447] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes
[    0.985692] tegra_camera_platform tegra-camera-platform: tegra_camera_probe:camera_platform_driver probe
[    0.985951] misc tegra_camera_ctrl: tegra_camera_isomgr_register isp_iso_bw=1500000, vi_iso_bw=750000, max_bw=1500000
[    0.986358] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes
[    0.986418] Adding domain tsec-pd to PM domain host1x-pd
[    0.989788] tsec 54500000.tsec: initialized
[    0.991195] tsec 54100000.tsecb: initialized
[    0.991916] Adding domain nvdec-pd to PM domain host1x-pd
[    0.995299] nvdec 54480000.nvdec: initialized
[    0.996368] Adding domain vic03-pd to PM domain host1x-pd
[    0.996572] Adding domain msenc-pd to PM domain host1x-pd
[    0.996751] Adding domain nvjpg-pd to PM domain host1x-pd
[    1.000864] falcon 54340000.vic: initialized
[    1.002210] falcon 544c0000.nvenc: initialized
[    1.003536] falcon 54380000.nvjpg: initialized
[    1.007858] tegra_cec 70015000.tegra_cec: dt=1 start=0x70015000 end=0x70015FFF irq=97
[    1.007944] tegra_cec 70015000.tegra_cec: Enable clock result: 0.
[    1.007995] tegra_cec 70015000.tegra_cec: tegra_cec_init started
[    1.008105] tegradc tegradc.0: disp0 connected to head0->/host1x/sor1
[    1.008250] display board info: id 0x0, fab 0x0
[    1.008315] tegra_cec 70015000.tegra_cec: cec_add_sysfs ret=0
[    1.008330] generic_infoframe_type: 0x87
[    1.008352] tegra_cec 70015000.tegra_cec: probed
[    1.008480] tegradc tegradc.0: DT parsed successfully
[    1.008549] tegradc tegradc.0: Display dc.ffffff800ab40000 registered with id=0
[    1.016007] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels
[    1.017129] tegradc tegradc.0: probed
[    1.017912] Console: switching to colour frame buffer device 80x30
[    1.017965] tegradc tegradc.0: fb registered
[    1.019407] tegradc tegradc.1: disp1 connected to head1->/host1x/sor
[    1.019516] tegradc tegradc.1: No lt-data, using default setting
[    1.019570] tegradc tegradc.1: No hpd-gpio in DT
[    1.019622] tegradc tegradc.1: DT parsed successfully
[    1.019690] tegradc tegradc.1: Display dc.ffffff800acc0000 registered with id=1
[    1.021153] tegradc tegradc.1: dpd enable lookup fail:-19
[    1.022084] tegra-adma 702e2000.adma: Tegra210 ADMA driver registered 22 channels
[    1.022998] tegra-fuse-burn 7000f800.efuse:efuse-burn: Fuse burn driver initialized
[    1.023361] kfuse 7000fc00.kfuse: initialized
[    1.024256] tegra-pmc-iopower pmc-iopower: Regulator supply iopower-dbg-supply not available
[    1.527338] Host read timeout at address 545c00c4
[    1.527651] tegra-pmc-iopower pmc-iopower: NO_IOPOWER setting 0x0
[    1.528521] tegradc tegradc.1: probed
[    1.528795] tegra-dfll-pwm 70110000.pwm: DFLL_PWM regulator is available now
[    1.528822] vdd-cpu: 708 <--> 1322 mV at 708 mV 
[    1.528929] tegradc tegradc.1: fb registered
[    1.529259] pwm-regulator pwm_regulators:pwm-regulator@0: PWM regulator registration passed
[    1.530992] vdd-gpu: applied init 1000000uV constraint
[    1.531018] vdd-gpu: 708 <--> 1323 mV at 997 mV 
[    1.531422] pwm-regulator pwm_regulators:pwm-regulator@1: PWM regulator registration passed
[    1.532157] hpd: state 7 (Takeover from bootloader), hpd 0, pending_hpd_evt 1
[    1.532184] hpd: switching from state 7 (Takeover from bootloader) to state 0 (Reset)
[    1.532206] hpd: state 0 (Reset), hpd 0, pending_hpd_evt 0
[    1.532238] tegradc tegradc.1: blank - powerdown
[    1.532269] extcon-disp-state extcon:disp-state: cable 44 state 0 already set.
[    1.532286] Extcon DP: HPD disabled
[    1.532298] hpd: hpd_switch 0
[    1.532311] hpd: switching from state 0 (Reset) to state 1 (Check Plug)
[    1.532331] hpd: state 1 (Check Plug), hpd 0, pending_hpd_evt 0
[    1.532348] hpd: switching from state 1 (Check Plug) to state 3 (Disabled)
[    1.535008] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    1.535133] No Device Node present for smmu client: serial8250 !!
[    1.535153] platform serial8250: No iommus property found in DT node, got swgids from fixup(101004000)
[    1.535205] iommu: Adding device serial8250 to group 35
[    1.537468] console [ttyS0] disabled
[    1.537590] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 63, base_baud = 25500000) is a Tegra
[    2.041532] tegra_cec 70015000.tegra_cec: Can't find physical addresse.
[    2.041537] tegra_cec 70015000.tegra_cec: tegra_cec_init Done.
[    2.093083] tegra-pcie 1003000.pcie: link 0 down, retrying
[    2.765262] tegra-pcie 1003000.pcie: link 0 down, retrying
[    3.169530] tegra-pcie 1003000.pcie: link 0 down, retrying
[    3.171546] tegra-pcie 1003000.pcie: link 0 down, ignoring
[    3.277714] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00
[    3.277724] pci_bus 0000:00: root bus resource [io  0x0000-0xffff]
[    3.277735] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff]
[    3.277740] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref]
[    3.277745] pci_bus 0000:00: root bus resource [bus 00-ff]
[    3.278152] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    3.290257] pci 0000:00:02.0: BAR 14: assigned [mem 0x13000000-0x130fffff]
[    3.290262] pci 0000:00:02.0: BAR 13: assigned [io  0x1000-0x1fff]
[    3.290271] pci 0000:01:00.0: BAR 4: assigned [mem 0x13000000-0x13003fff 64bit]
[    3.290291] pci 0000:01:00.0: BAR 2: assigned [mem 0x13004000-0x13004fff 64bit]
[    3.290310] pci 0000:01:00.0: BAR 0: assigned [io  0x1000-0x10ff]
[    3.290320] pci 0000:00:02.0: PCI bridge to [bus 01]
[    3.290326] pci 0000:00:02.0:   bridge window [io  0x1000-0x1fff]
[    3.290332] pci 0000:00:02.0:   bridge window [mem 0x13000000-0x130fffff]
[    3.290729] pcieport 0000:00:02.0: Signaling PME through PCIe PME interrupt
[    3.290733] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
[    4.063602] console [ttyS0] enabled
[    4.068339] 70006040.serial: ttyTHS1 at MMIO 0x70006040 (irq = 64, base_baud = 0) is a TEGRA_UART
[    4.077561] serial-tegra 70006200.serial: RX in PIO mode
[    4.082994] 70006200.serial: ttyTHS2 at MMIO 0x70006200 (irq = 65, base_baud = 0) is a TEGRA_UART
[    4.092979] [drm] Initialized
[    4.105943] brd: module loaded
[    4.114551] loop: module loaded
[    4.117819] tegra_profiler: version: 1.139, samples/io: 47/27
[    4.123736] tegra_profiler: auth: init
[    4.128856] THERMAL EST: found 2 subdevs
[    4.132858] THERMAL EST num_resources: 0
[    4.136810] [THERMAL EST subdev 0]
[    4.140284] [THERMAL EST subdev 1]
[    4.144152] thermal thermal_zone5: Registering thermal zone thermal_zone5 for type thermal-fan-est
[    4.153126] THERMAL EST: thz register success.
[    4.157722] THERMAL EST: end of probe, return err: 0
[    4.163964] hisi_sas: driver version v1.6
[    4.172473] tegra-qspi 70410000.spi: Prod settings list not found
[    4.179820] qspi_mtd spi32766.0: MX25U3235F (4096 Kbytes)
[    4.185264] qspi_mtd spi32766.0: mtd .name = spi32766.0, .size = 0x400000 (4MiB) .erasesize = 0x00001000 (4KiB) .numeraseregions = 0
[    4.200303] libphy: Fixed MDIO Bus: probed
[    4.205181] tun: Universal TUN/TAP device driver, 1.6
[    4.210262] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    4.217421] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[    4.223283] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    4.229279] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
[    4.236249] igb: Copyright (c) 2007-2014 Intel Corporation.
[    4.241887] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k
[    4.249724] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
[    4.255700] Intel(R) 10GbE PCI Express Linux Network Driver - version 4.6.4
[    4.262668] Copyright(c) 1999 - 2017 Intel Corporation.
[    4.268866] r8168 0000:01:00.0: enabling device (0000 -> 0003)
[    4.274756] r8168 Gigabit Ethernet driver 8.045.08-NAPI loaded
[    4.294780] r8168 0000:01:00.0 (unnamed net_device) (uninitialized): Invalid ethernet address 00:00:00:00:00:00, trying device tree node
[    4.307217] r8168 0000:01:00.0 (unnamed net_device) (uninitialized): Found valid ethernet address 00:04:4b:e6:53:41 from device tree
[    4.319697] r8168: This product is covered by one or more of the following patents: US6,570,884, US6,115,776, and US6,327,625.
[    4.331149] r8168  Copyright (C) 2017  Realtek NIC software team <nicfae@realtek.com> 
[    4.331149]  This program comes with ABSOLUTELY NO WARRANTY; for details, please see <http://www.gnu.org/licenses/>. 
[    4.331149]  This is free software, and you are welcome to redistribute it under certain conditions; see <http://www.gnu.org/licenses/>. 
[    4.362566] PPP generic driver version 2.4.2
[    4.367046] PPP BSD Compression module registered
[    4.371771] PPP Deflate Compression module registered
[    4.376863] PPP MPPE Compression module registered
[    4.381670] NET: Registered protocol family 24
[    4.386189] usbcore: registered new interface driver r8152
[    4.391736] usbcore: registered new interface driver asix
[    4.397198] usbcore: registered new interface driver ax88179_178a
[    4.403343] usbcore: registered new interface driver cdc_ether
[    4.409220] usbcore: registered new interface driver net1080
[    4.414932] usbcore: registered new interface driver cdc_subset
[    4.420904] usbcore: registered new interface driver zaurus
[    4.426542] usbcore: registered new interface driver cdc_ncm
[    4.432383] VFIO - User Level meta-driver version: 0.3
[    4.438784] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.445356] ehci-pci: EHCI PCI platform driver
[    4.449858] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    4.456058] ohci-pci: OHCI PCI platform driver
[    4.460552] ohci-platform: OHCI generic platform driver
[    4.468477] tegra-xusb 70090000.xusb: USB2 port 0 has OTG_CAP
[    4.474851] tegra-xusb-padctl 7009f000.xusb_padctl: enabled OTG on UTMI pad 0
[    4.483187] tegra-xusb 70090000.xusb: extcon 0: ffffffc0f969dc00 id
[    4.491525] usbcore: registered new interface driver uas
[    4.492375] tegra-xusb 70090000.xusb: Firmware timestamp: 2019-10-17 15:58:59 UTC, Version: 50.25 release
[    4.492441] tegra-xusb 70090000.xusb: xHCI Host Controller
[    4.492465] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 1
[    4.493250] tegra-xusb 70090000.xusb: hcc params 0x0184f525 hci version 0x100 quirks 0x00050010
[    4.493311] tegra-xusb 70090000.xusb: irq 61, io mem 0x70090000
[    4.493516] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    4.493522] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.493526] usb usb1: Product: xHCI Host Controller
[    4.493529] usb usb1: Manufacturer: Linux 4.9.140-tegra xhci-hcd
[    4.493533] usb usb1: SerialNumber: 70090000.xusb
[    4.494213] hub 1-0:1.0: USB hub found
[    4.494294] hub 1-0:1.0: 5 ports detected
[    4.494895] tegra-xusb 70090000.xusb: xHCI Host Controller
[    4.494908] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 2
[    4.495004] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    4.495108] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[    4.495113] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.495116] usb usb2: Product: xHCI Host Controller
[    4.495120] usb usb2: Manufacturer: Linux 4.9.140-tegra xhci-hcd
[    4.495123] usb usb2: SerialNumber: 70090000.xusb
[    4.495567] hub 2-0:1.0: USB hub found
[    4.495599] hub 2-0:1.0: 4 ports detected
[    4.598176] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 1
[    4.636989] usbcore: registered new interface driver usb-storage
[    4.643155] usbcore: registered new interface driver usbserial
[    4.652522] tegra-xudc-new 700d0000.xudc: device count: 1
[    4.659261] tegra-xudc-new 700d0000.xudc: USB charger detection disabled
[    4.665997] tegra-xudc-new 700d0000.xudc: vbus state: 1
[    4.671264] tegra-xudc-new 700d0000.xudc: device mode on: 0
[    4.676871] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 0
[    4.683587] tegra-xudc-new 700d0000.xudc: active: 0 => 1
[    4.689585] mousedev: PS/2 mouse device common for all mice
[    4.695280] usbcore: registered new interface driver xpad
[    4.822129] usb 1-2: new high-speed USB device number 2 using tegra-xusb
[    4.831160] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0
[    4.840963] rtc rtc1: alarm rtc device
[    4.844758] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1
[    4.851986] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock
[    4.858779] i2c /dev entries driver
[    4.864119] imx219 6-0010: tegracam sensor driver:imx219_v2.0.6
[    4.878363] usb 1-2: New USB device found, idVendor=0bda, idProduct=5411
[    4.885085] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    4.892234] usb 1-2: Product: 4-Port USB 2.1 Hub
[    4.893433] tegra-vii2c 546c0000.i2c: no acknowledge from address 0x10
[    4.893502] imx219 6-0010: imx219_board_setup: error during i2c read probe (-121)
[    4.893530] imx219 6-0010: board setup failed
[    4.893627] imx219: probe of 6-0010 failed with error -121
[    4.894555] max77620-power max77620-power: Event recorder REG_NVERC : 0x0
[    4.897277] tegra_soctherm 700e2000.soctherm: pllx_offset tz:0 max:14, min:2
[    4.897282] tegra_soctherm 700e2000.soctherm: pllx_offset tz:2 max:8, min:4
[    4.897737] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[    4.897755] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when cpu reaches 102500 mC
[    4.897764] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when cpu reaches 100500 mC
[    4.897894] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[    4.897904] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when gpu reaches 103000 mC
[    4.897909] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when gpu reaches 101000 mC
[    4.898058] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[    4.898068] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when pll reaches 127000 mC
[    4.898073] tegra_soctherm 700e2000.soctherm: throttrip: pll: missing hot temperature
[    4.898288] tegra_soctherm 700e2000.soctherm: failed to register sensor: -19
[    4.899051] tegra_aotag tegra-aotag: Registering sensor 0
[    4.899102] tegra_aotag tegra-aotag: Invalid temp readout
[    4.899127] tegra_aotag tegra-aotag: Invalid temp readout
[    4.899143] tegra_aotag tegra-aotag: Bound to TZ : ID 0
[    4.899152] tegra_aotag tegra-aotag: Probe done [SUCCESS]:0
[    4.900002] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[    4.900022] tegra_dfll_action dfll-cdev-cap: Tegra DFLL 'cap cooling device' registered
[    4.900202] tegra_aotag tegra-aotag: Invalid temp readout
[    4.900234] tegra_dfll_action dfll-cdev-floor: Tegra DFLL 'floor cooling device' registered
[    4.900622] parse_throttle_dt_data: Num cap clks = 6
[    4.900627] parse_throttle_dt_data: clk=cclk_g type=2
[    4.900642] parse_throttle_dt_data: clk=gpu type=4
[    4.900663] parse_throttle_dt_data: clk=cap.throttle.c2bus type=0
[    4.900681] parse_throttle_dt_data: clk=cap.throttle.c3bus type=0
[    4.900700] parse_throttle_dt_data: clk=cap.throttle.sclk type=0
[    4.900704] parse_throttle_dt_data: clk=emc type=3
[    4.901083] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[    4.901170] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[    4.901290] tegra_throttle_probe: probe successful. #cdevs=4
[    4.901997] FAN dev name: pwm-fan
[    4.902085] FAN:gpio request success.
[    4.902189] pwm_fan_driver pwm-fan: cap state:7, cap pwm:255
[    4.902490] pwm_fan_driver pwm-fan: got pwm for fan. polarity is normal
[    4.902666] pwm_fan_driver pwm-fan: fan tach request irq success
[    4.902674] pwm_fan_driver pwm-fan: tach period: 1000
[    4.902796] pwm_fan_driver pwm-fan: index 0: pwm=0, rpm=0, rru=40, rrd=40, state:2
[    4.902801] pwm_fan_driver pwm-fan: index 1: pwm=80, rpm=1000, rru=2, rrd=2, state:2
[    4.902805] pwm_fan_driver pwm-fan: index 2: pwm=120, rpm=2000, rru=1, rrd=1, state:2
[    4.902809] pwm_fan_driver pwm-fan: index 3: pwm=160, rpm=3000, rru=1, rrd=1, state:2
[    4.902812] pwm_fan_driver pwm-fan: index 4: pwm=255, rpm=4000, rru=1, rrd=1, state:3
[    4.902816] pwm_fan_driver pwm-fan: index 5: pwm=255, rpm=5000, rru=1, rrd=1, state:3
[    4.902820] pwm_fan_driver pwm-fan: index 6: pwm=255, rpm=6000, rru=1, rrd=1, state:3
[    4.902823] pwm_fan_driver pwm-fan: index 7: pwm=255, rpm=7000, rru=1, rrd=1, state:4
[    4.902827] pwm_fan_driver pwm-fan: index 8: pwm=255, rpm=10000, rru=1, rrd=1, state:4
[    4.902831] pwm_fan_driver pwm-fan: index 9: pwm=255, rpm=11000, rru=1, rrd=1, state:4
[    4.903465] tegra-wdt 60005100.watchdog: Tegra WDT enabled on probe. Timeout = 120 seconds.
[    4.903932] tegra-wdt 60005100.watchdog: initialized (timeout = 120 sec, nowayout = 1)
[    4.905051] device-mapper: uevent: version 1.0.3
[    4.905560] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com
[    4.911052] tegra210-cpufreq cpufreq: probe()...completed
[    4.911818] sdhci: Secure Digital Host Controller Interface driver
[    4.911820] sdhci: Copyright(c) Pierre Ossman
[    4.911821] sdhci-pltfm: SDHCI platform and OF driver helper
[    4.912303] sdhci-tegra sdhci-tegra.0: Got CD GPIO
[    4.912647] sdhci-tegra sdhci-tegra.0: Client registration for eMC Successful
[    4.912768] sdhci-tegra sdhci-tegra.0: wakeup init done, cdirq 300
[    4.917217] tegra-se 70012000.se: tegra_se_probe: complete
[    4.917717] hidraw: raw HID events driver (C) Jiri Kosina
[    4.918835] usbcore: registered new interface driver usbhid
[    4.918836] usbhid: USB HID core driver
[    4.920797] tegra21x_actmon 6000c800.actmon: in actmon_register()...
[    4.921045] tegra21x_actmon 6000c800.actmon: initialization Completed for the device mc_all
[    4.922978] nvpmodel: initialized successfully
[    4.924131] usbcore: registered new interface driver snd-usb-audio
[    4.924194] No Device Node present for smmu client: snd-soc-dummy !!
[    4.924198] platform snd-soc-dummy: No iommus property found in DT node, got swgids from fixup(101004000)
[    4.924216] iommu: Adding device snd-soc-dummy to group 36
[    4.944422] OPE platform probe
[    4.944508] OPE platform probe successful
[    4.944835] OPE platform probe
[    4.944916] OPE platform probe successful
[    4.962249] mmc0: SDHCI controller on sdhci-tegra.0 [sdhci-tegra.0] using ADMA 64-bit with 64 bit addr
[    4.971451] tegra-asoc: sound: ADMAIF1 <-> ADMAIF1 mapping ok
[    4.971576] tegra-asoc: sound: ADMAIF2 <-> ADMAIF2 mapping ok
[    4.971702] tegra-asoc: sound: ADMAIF3 <-> ADMAIF3 mapping ok
[    4.971824] tegra-asoc: sound: ADMAIF4 <-> ADMAIF4 mapping ok
[    4.971942] tegra-asoc: sound: ADMAIF5 <-> ADMAIF5 mapping ok
[    4.972062] tegra-asoc: sound: ADMAIF6 <-> ADMAIF6 mapping ok
[    4.972181] tegra-asoc: sound: ADMAIF7 <-> ADMAIF7 mapping ok
[    4.972298] tegra-asoc: sound: ADMAIF8 <-> ADMAIF8 mapping ok
[    4.972426] tegra-asoc: sound: ADMAIF9 <-> ADMAIF9 mapping ok
[    4.972543] tegra-asoc: sound: ADMAIF10 <-> ADMAIF10 mapping ok
[    4.983797] u32 classifier
[    4.983799]     Actions configured
[    4.983870] Initializing XFRM netlink socket
[    4.984583] NET: Registered protocol family 10
[    4.985315] NET: Registered protocol family 17
[    4.985326] NET: Registered protocol family 15
[    4.985399] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    4.985442] Bluetooth: RFCOMM socket layer initialized
[    4.985451] Bluetooth: RFCOMM ver 1.11
[    4.985457] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    4.985462] Bluetooth: HIDP socket layer initialized
[    4.985480] 9pnet: Installing 9P2000 support
[    4.985514] Key type dns_resolver registered
[    4.988115] Registered cp15_barrier emulation handler
[    4.988122] Registered setend emulation handler
[    4.989162] registered taskstats version 1
[    4.989729] Adding domain ve2-pd to PM domain host1x-pd
[    4.989970] Adding domain ve-pd to PM domain host1x-pd
[    4.993350] isp 54600000.isp: initialized
[    4.994801] isp 54680000.isp: initialized
[    5.004773] last reset is due to software reset
[    5.004776] KERNEL: PMC reset status reg: 0x3
[    5.004850] BL: PMC reset status reg: 0x3
[    5.004851] BL: PMIC poweroff Event Recorder: 0x0
[    5.006328] clk_cbus_recalc_rate: no gbus parent
[    5.006332] clk_cbus_round_rate: no gbus parent
[    5.006337] clk_cbus_round_rate: no gbus parent
[    5.006344] clk_cbus_recalc_rate: no gbus parent
[    5.006445] clk_cbus_recalc_rate: no gbus parent
[    5.006447] clk_cbus_round_rate: no gbus parent
[    5.006449] clk_cbus_round_rate: no gbus parent
[    5.006452] clk_cbus_recalc_rate: no gbus parent
[    5.007115] tegra_dvfs: GPU-cap: registered
[    5.007168] tegra dvfs: vdd-cpu: nominal 1168mV, offset 708000uV, step 19200uV, scaling enabled
[    5.007170] tegra dvfs: vdd-core: nominal 1075mV, offset 600000uV, step 12500uV, scaling enabled
[    5.007171] tegra dvfs: vdd-gpu: nominal 1058mV, offset 708000uV, step 10000uV, scaling enabled
[    5.008499] tegra_dvfs: vdd-gpu-vts: registered
[    5.009179] tegra_core_action core_dvfs_cdev_floor: Tegra CORE DVFS 'floor cooling device' registered
[    5.009772] tegra_core_action core_dvfs_cdev_cap: Tegra CORE DVFS 'cap cooling device' registered
[    5.010398] input: gpio-keys as /devices/gpio-keys/input/input0
[    5.020445] mmc0: new SDHC card at address 0001
[    5.020727] mmcblk0: mmc0:0001 SD16G 29.8 GiB 
[    5.046343] tegra_rtc 7000e000.rtc: setting system clock to 2000-01-01 01:12:07 UTC (946689127)
[    5.047398] vi 54080000.vi: vi_probe: ++
[    5.049958] vi 54080000.vi: initialized
[    5.051937] vi 54080000.vi: subdev nvcsi--1 bound
[    5.052165] mmcblk mmc0:0001: Card claimed for testing.
[    5.053446] Disable partitions left on by BL
[    5.053448]   disb
[    5.053491] bwmgr: missing cdev-type property
[    5.053582] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[    5.053587] DRAM derating cdev registered.
[    5.054566] vdd-fan: disabling
[    5.054568] vdd-usb-vbus: disabling
[    5.054570] vdd-usb-vbus2: disabling
[    5.054578] avdd-io-edp-1v05: disabling
[    5.054673] ALSA device list:
[    5.054675]   #1: tegra-snd-t210ref-mobile-rt565x
[    5.190971]  mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14
[    5.772393] usb 1-2: Manufacturer: Generic
[    5.777254] input: tegra-hda HDMI/DP,pcm=3 as /devices/70030000.hda/sound/card0/input1
[    5.785158] Freeing unused kernel memory: 8576K
[    5.785337] hub 1-2:1.0: USB hub found
[    5.789815] hub 1-2:1.0: 4 ports detected
[    5.816305] Root device found: mmcblk0p1
[    5.821395] Found dev node: /dev/mmcblk0p1
[    6.086174] usb 1-2.1: new low-speed USB device number 3 using tegra-xusb
[    6.118604] usb 1-2.1: New USB device found, idVendor=040b, idProduct=2000
[    6.125481] usb 1-2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    6.132786] usb 1-2.1: Product: USB Keyboard
[    6.137055] usb 1-2.1: Manufacturer: Generic
[    6.146549] input: Generic USB Keyboard as /devices/70090000.xusb/usb1/1-2/1-2.1/1-2.1:1.0/0003:040B:2000.0001/input/input2
[    6.214588] hid-generic 0003:040B:2000.0001: input,hidraw0: USB HID v1.10 Keyboard [Generic USB Keyboard] on usb-70090000.xusb-2.1/input0
[    6.232668] input: Generic USB Keyboard as /devices/70090000.xusb/usb1/1-2/1-2.1/1-2.1:1.1/0003:040B:2000.0002/input/input3
[    6.302580] hid-generic 0003:040B:2000.0002: input,hidraw1: USB HID v1.10 Mouse [Generic USB Keyboard] on usb-70090000.xusb-2.1/input1
[    6.394172] usb 1-2.3: new low-speed USB device number 4 using tegra-xusb
[    6.422788] usb 1-2.3: New USB device found, idVendor=093a, idProduct=2510
[    6.429666] usb 1-2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    6.436972] usb 1-2.3: Product: USB Optical Mouse
[    6.441672] usb 1-2.3: Manufacturer: PixArt
[    6.449307] input: PixArt USB Optical Mouse as /devices/70090000.xusb/usb1/1-2/1-2.3/1-2.3:1.0/0003:093A:2510.0003/input/input4
[    6.461084] hid-generic 0003:093A:2510.0003: input,hidraw2: USB HID v1.11 Mouse [PixArt USB Optical Mouse] on usb-70090000.xusb-2.3/input0
[    8.658661] tegra-xusb 70090000.xusb: Upgrade port 0 to USB3.0
[    8.664488] tegra-xusb 70090000.xusb: Upgrade port 1 to USB3.0
[    8.987127] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb
[    9.025871] usb 2-1: New USB device found, idVendor=0bda, idProduct=0411
[    9.032577] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    9.039709] usb 2-1: Product: 4-Port USB 3.1 Hub
[    9.044325] usb 2-1: Manufacturer: Generic
[    9.053019] hub 2-1:1.0: USB hub found
[    9.059378] hub 2-1:1.0: 4 ports detected
[    9.222170] usb 2-1: usb_suspend_both: status 0
[    9.226807] usb usb2: usb_suspend_both: status 0
[   27.969238] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)
[   27.978159] Rootfs mounted over mmcblk0p1
[   55.969134] random: crng init done
[   82.313747] Switching from initrd to actual rootfs
[  286.479477] systemd[1]: System time before build time, advancing clock.
[  306.734225] ip_tables: (C) 2000-2006 Netfilter Core Team
[  308.084037] cgroup: cgroup2: unknown option "nsdelegate"
[  315.621261] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[  315.643302] systemd[1]: Detected architecture arm64.
[  318.506872] systemd[1]: No hostname configured.
[  318.511433] systemd[1]: Set hostname to <localhost>.
[  322.123368] systemd[1]: Initializing machine ID from random generator.
[  362.110461] systemd[1]: File /lib/systemd/system/systemd-journald.service:36 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling.
[  362.127504] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.)
[  404.896514] systemd[1]: Reached target Swap.
[  404.902930] systemd[1]: Created slice System Slice.
[  404.907973] systemd[1]: Reached target Slices.
[  404.912669] systemd[1]: Listening on fsck to fsckd communication Socket.
[  404.919629] systemd[1]: Listening on Journal Socket (/dev/log).
[  404.925758] systemd[1]: Listening on RPCbind Server Activation Socket.
[  404.932561] systemd[1]: Listening on Journal Socket.
[  404.939757] systemd[1]: Starting Set console scheme...
[  405.364266] systemd[1]: Starting Set the console keyboard layout...
[  405.373076] systemd[1]: Mounting POSIX Message Queue File System...
[  419.481342] systemd[1]: Starting Load Kernel Modules...
[  419.486905] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[  419.495625] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[  430.084798] systemd[1]: Listening on udev Control Socket.
[  430.090487] systemd[1]: Listening on udev Kernel Socket.
[  430.098128] systemd[1]: Starting udev Coldplug all Devices...
[  430.106277] systemd[1]: Starting Remount Root and Kernel File Systems...
[  430.115671] systemd[1]: Mounting Kernel Debug File System...
[  430.121807] systemd[1]: Listening on Journal Audit Socket.
[  430.129688] systemd[1]: Starting Journal Service...
[  430.171490] systemd[1]: Started Create list of required static device nodes for the current kernel.
[  430.183619] systemd[1]: Starting Create Static Device Nodes in /dev...
[  457.223323] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null)
[  457.224527] systemd[1]: Mounted POSIX Message Queue File System.
[  457.236669] systemd[1]: Mounted Huge Pages File System.
[  457.244347] systemd[1]: Started Remount Root and Kernel File Systems.
[  457.251730] systemd[1]: Mounted Kernel Debug File System.
[  457.260436] systemd[1]: Starting Load/Save Random Seed...
[  487.434078] systemd[1]: systemd-random-seed.service: Start operation timed out. Terminating.
[  509.684086] systemd[1]: systemd-modules-load.service: Start operation timed out. Terminating.
[  515.644468] systemd[1]: Started Journal Service.
[  538.412951] systemd-journald[2009]: Received request to flush runtime journal from PID 1
[ 1088.626204] INFO: task systemd-tmpfile:3743 blocked for more than 120 seconds.
[ 1088.633434]       Not tainted 4.9.140-tegra #1
[ 1088.637881] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1088.645793] Kernel panic - not syncing: hung_task: blocked tasks
[ 1088.651788] CPU: 2 PID: 584 Comm: khungtaskd Not tainted 4.9.140-tegra #1
[ 1088.658562] Hardware name: NVIDIA Jetson Nano Developer Kit (DT)
[ 1088.664555] Call trace:
[ 1088.666996] [<ffffff800808bdb8>] dump_backtrace+0x0/0x198
[ 1088.672383] [<ffffff800808c37c>] show_stack+0x24/0x30
[ 1088.677426] [<ffffff800845d820>] dump_stack+0x98/0xc0
[ 1088.682467] [<ffffff80081c2198>] panic+0x11c/0x298
[ 1088.687250] [<ffffff8008181f90>] watchdog+0x300/0x3b8
[ 1088.692290] [<ffffff80080dbee4>] kthread+0xec/0xf0
[ 1088.697071] [<ffffff8008083850>] ret_from_fork+0x10/0x40
[ 1088.702373] SMP: stopping secondary CPUs
[ 1088.706338] Kernel Offset: disabled
[ 1088.709820] Memory Limit: none
[ 1088.718923] Rebooting in 5 seconds..
[0000.159] [L4T TegraBoot] (version 00.00.2018.01-l4t-39a9dc3d)
[0000.165] Processing in cold boot mode Bootloader 2
[0000.169] A02 Bootrom Patch rev = 1023
[0000.173] Power-up reason: software reset
[0000.177] No Battery Present
[0000.179] pmic max77620 reset reason
[0000.183] pmic max77620 NVERC : 0x0
[0000.186] RamCode = 0
[0000.188] Platform has DDR4 type RAM
[0000.192] max77620 disabling SD1 Remote Sense
[0000.196] Setting DDR voltage to 1125mv
[0000.200] Serial Number of Pmic Max77663: 0x1727e5
[0000.208] Entering ramdump check
[0000.211] Get RamDumpCarveOut = 0x0
[0000.214] RamDumpCarveOut=0x0,  RamDumperFlag=0xe59ff3f8
[0000.219] Last reboot was clean, booting normally!
[0000.224] Sdram initialization is successful 
[0000.228] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000
[0000.234] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000
[0000.240] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000
[0000.245] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000
[0000.251] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000
[0000.257] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000
[0000.263] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000
[0000.269] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000
[0000.285] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000
[0000.291] Platform-DebugCarveout: 0
[0000.294] Nck Carveout Base=0x00000000ff080000 Size=0x00200000
[0000.300] Non secure mode, and RB not enabled.
[0000.341] Csd NumOfBlocks=62423040
[0000.346] Set High speed to 1
[0000.351] Using GPT Primary to query partitions
[0000.357] Loading Tboot-CPU binary
[0000.366] Verifying TBC in OdmNonSecureSBK mode
[0000.376] Bootloader load address is 0xa0000000, entry address is 0xa0000258
[0000.383] Bootloader downloaded successfully.
[0000.387] Downloaded Tboot-CPU binary to 0xa0000258
[0000.392] MAX77620_GPIO5 configured
[0000.396] CPU power rail is up
[0000.398] CPU clock enabled
[0000.402] Performing RAM repair
[0000.405] Updating A64 Warmreset Address to 0xa00002e9
[0000.410] Loading NvTbootBootloaderDTB
[0000.435] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode
[0000.500] Bootloader DTB Load Address: 0x83000000
[0000.505] Loading NvTbootKernelDTB
[0000.529] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode
[0000.594] Kernel DTB Load Address: 0x83100000
[0000.599] Loading cboot binary
[0000.629] Verifying EBT in OdmNonSecureSBK mode
[0000.670] Bootloader load address is 0x92c00000, entry address is 0x92c00258
[0000.677] Bootloader downloaded successfully.
[0000.694] Using BFS PT to query partitions 
[0000.698] Next binary entry address: 0x92c00258 
[0000.703] BoardId: 3448
[0000.707] Overriding pmu board id with proc board id
[0000.712] Display board id is not available 
[0000.740] Verifying SC7EntryFw in OdmNonSecureSBK mode
[0000.792] /bpmp deleted
[0000.795] SC7EntryFw header found loaded at 0xff700000
[0000.983] OVR2 PMIC
[0000.985] Bpmp FW successfully loaded
[0000.990] WB0 init successfully at 0xff780000
[0000.994] Set NvDecSticky Bits
[0000.997] GSC2 address ff53fffc value c0edbbcc
[0001.004] GSC MC Settings done
[0001.007] TOS Image length 53680
[0001.010]  Monitor size 53680
[0001.013]  OS size 0
[0001.020] Secure Os AES-CMAC Verification Success!
[0001.025] TOS image cipher info: plaintext
[0001.029] Loading and Validation of Secure OS Successful
[0001.045] SC7 Entry Firmware - 0xff700000, 0x4000
[0001.049] NvTbootPackSdramParams: start. 
[0001.054] NvTbootPackSdramParams: done. 
[0001.058] Tegraboot started after 87450 us
[0001.062] Basic modules init took 646735 us
[0001.066] Sec Bootdevice Read Time = 12 ms, Read Size = 65 KB
[0001.072] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB
[0001.077] Storage Device Read Time = 109 ms, Read Size = 2226 KB
[0001.083] Storage Device Write Time = 0 ms, Write Size = 0 KB
[0001.088] Next stage binary read took 24544 us
[0001.093] Carveout took -36207 us
[0001.096] CPU initialization took 361424 us
[0001.100] Total time taken by TegraBoot 996496 us

[0001.104] Starting CPU & Halting co-processor 

64NOTICE:  BL31: v1.3(release):23b153a63
NOTICE:  BL31: Built : 22:39:57, Dec  9 2019
ERROR:   Error initializing runtime service trusty_fast
[0001.227] RamCode = 0
[0001.231] LPDDR4 Training: Read DT: Number of tables = 2
[0001.236] EMC Training (SRC-freq: 204000; DST-freq: 1600000)
[0001.249] EMC Training Successful
[0001.252] 408000 not found in DVFS table
[0001.259] RamCode = 0
[0001.262] DT Write: emc-table@204000 succeeded
[0001.267] DT Write: emc-table@1600000 succeeded
[0001.272] LPDDR4 Training: Write DT: Number of tables = 2
[0001.312] 
[0001.313] Debug Init done
[0001.315] Marked DTB cacheable
[0001.318] Bootloader DTB loaded at 0x83000000
[0001.323] Marked DTB cacheable
[0001.326] Kernel DTB loaded at 0x83100000
[0001.330] DeviceTree Init done
[0001.345] Pinmux applied successfully
[0001.350] gicd_base: 0x50041000
[0001.353] gicc_base: 0x50042000
[0001.356] Interrupts Init done
[0001.360] Using base:0x60005090 & irq:208 for tick-timer
[0001.365] Using base:0x60005098 for delay-timer
[0001.370] platform_init_timer: DONE
[0001.373] Timer(tick) Init done
[0001.377] osc freq = 38400 khz
[0001.381] 
[0001.382] Welcome to L4T Cboot
[0001.385] 
[0001.386] Cboot Version: 00.00.2018.01-t210-40c3ff9c
[0001.391] calling constructors
[0001.394] initializing heap
[0001.397] initializing threads
[0001.400] initializing timers
[0001.403] creating bootstrap completion thread
[0001.407] top of bootstrap2()
[0001.410] CPU: ARM Cortex A57
[0001.413] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000
[0001.418] initializing platform
[0001.425] Manufacturer: MF = 0xc2, ID MSB = 0x25
[0001.430] ID LSB = 0x36, ID-CFI len = 194 bytes
[0001.434] Macronix QSPI chip present
[0001.438] SPI device register
[0001.441] init boot device
[0001.443] allocating memory for boot device(SPI)
[0001.448] registering boot device
[0001.457] sdmmc node status = okay
[0001.460] sdcard instance = 0
[0001.463] sdcard gpio handle 0x56
[0001.467] sdcard gpio pin 0xc9
[0001.469] sdcard gpio flags 0x0
[0001.473] vmmc-supply 0x99
[0001.475] Instance: 0
[0001.477] Allocating memory for context
[0001.481] enabling clock
[0001.483] sd card init
[0001.486] Check card present and stable
[0001.489] Send command 0
[0001.506] Send command 3
[0001.510] Set RCA for the card
[0001.513] Query card specific data by command 9
[0001.520] Parse CSD data
[0001.522] Send command 7
[0001.532] Calling sd device register
[0001.536] Init sdcard
[0001.538] Allocating memory for boot device
[0001.542] Registering user device
[0001.555] Enable APE clock
[0001.558] Un-powergate APE partition
[0001.561] of_register: registering tegra_udc to of_hal
[0001.566] of_register: registering inv20628-driver to of_hal
[0001.572] of_register: registering ads1015-driver to of_hal
[0001.578] of_register: registering lp8557-bl-driver to of_hal
[0001.583] of_register: registering bq2419x_charger to of_hal
[0001.589] of_register: registering bq27441_fuel_gauge to of_hal
[0001.601] gpio framework initialized
[0001.604] of_register: registering tca9539_gpio to of_hal
[0001.609] of_register: registering tca9539_gpio to of_hal
[0001.615] of_register: registering i2c_bus_driver to of_hal
[0001.620] of_register: registering i2c_bus_driver to of_hal
[0001.626] of_register: registering i2c_bus_driver to of_hal
[0001.631] pmic framework initialized
[0001.635] of_register: registering max77620_pmic to of_hal
[0001.640] regulator framework initialized
[0001.644] of_register: registering tps65132_bl_driver to of_hal
[0001.650] initializing target
[0001.656] gpio_driver_register: register 'tegra_gpio_driver' driver
[0001.664] board ID = D78, board SKU = 0
[0001.668] Skipping Z3!
[0001.673] fixed regulator driver initialized
[0001.690] initializing OF layer
[0001.693] NCK carveout not present
[0001.696] Skipping dts_overrides
[0001.700] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.717] I2C Bus Init done
[0001.720] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.730] I2C Bus Init done
[0001.733] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.743] I2C Bus Init done
[0001.746] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.756] I2C Bus Init done
[0001.759] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.769] I2C Bus Init done
[0001.772] of_children_init: Ops found for compatible string maxim,max77620
[0001.782] max77620_init using irq 118
[0001.787] register 'maxim,max77620' pmic
[0001.791] gpio_driver_register: register 'max77620-gpio' driver
[0001.797] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.808] I2C Bus Init done
[0001.812] NCK carveout not present
[0001.821] Find /i2c@7000c000's alias i2c0
[0001.825] get eeprom at 1-a0, size 256, type 0
[0001.834] Find /i2c@7000c500's alias i2c2
[0001.838] get eeprom at 3-a0, size 256, type 0
[0001.842] get eeprom at 3-ae, size 256, type 0
[0001.847] pm_ids_update: Updating 1,a0, size 256, type 0
[0001.852] I2C slave not started
[0001.855] I2C write failed
[0001.858] Writing offset failed
[0001.861] eeprom_init: EEPROM read failed
[0001.865] pm_ids_update: eeprom init failed
[0001.869] pm_ids_update: Updating 3,a0, size 256, type 0
[0001.899] pm_ids_update: The pm board id is 3448-0000-200
[0001.906] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0001.914] pm_ids_update: pm id update successful
[0001.918] pm_ids_update: Updating 3,ae, size 256, type 0
[0001.948] pm_ids_update: The pm board id is 3449-0000-200
[0001.955] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0001.962] pm_ids_update: pm id update successful
[0001.993] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0001.999] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0002.007] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0002.013] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0002.022] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e6:53:41
[0002.028] Plugin Manager: Parse ODM data 0x00094000
[0002.038] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0   
[0002.060] Find /i2c@7000c000's alias i2c0
[0002.063] get eeprom at 1-a0, size 256, type 0
[0002.072] Find /i2c@7000c500's alias i2c2
[0002.076] get eeprom at 3-a0, size 256, type 0
[0002.081] get eeprom at 3-ae, size 256, type 0
[0002.085] pm_ids_update: Updating 1,a0, size 256, type 0
[0002.090] I2C slave not started
[0002.093] I2C write failed
[0002.096] Writing offset failed
[0002.099] eeprom_init: EEPROM read failed
[0002.103] pm_ids_update: eeprom init failed
[0002.107] pm_ids_update: Updating 3,a0, size 256, type 0
[0002.137] pm_ids_update: The pm board id is 3448-0000-200
[0002.144] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0002.151] pm_ids_update: pm id update successful
[0002.155] pm_ids_update: Updating 3,ae, size 256, type 0
[0002.185] pm_ids_update: The pm board id is 3449-0000-200
[0002.192] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0002.199] pm_ids_update: pm id update successful
[0002.229] Add serial number:1422419088143 as DT property
[0002.237] Applying platform configs
[0002.244] platform-init is not present. Skipping
[0002.248] calling apps_init()
[0002.268] Found 14 GPT partitions in "sd0"
[0002.272] Proceeding to Cold Boot
[0002.275] starting app android_boot_app
[0002.279] Device state: unlocked
[0002.282] display console init
[0002.291] could not find regulator
[0002.314] hdmi cable not connected
[0002.317] is_hdmi_needed: HDMI not connected, returning false[0002.326] DT entry for leds-pwm not found

[0002.330] hdmi is not connected
[0002.333] sor0 is not supported
[0002.336] display_console_init: no valid display out_type
[0002.344] subnode volume_up is not found !
[0002.348] subnode back is not found !
[0002.352] subnode volume_down is not found !
[0002.356] subnode menu is not found !
[0002.360] Gpio keyboard init success
[0002.404] found decompressor handler: lz4-legacy
[0002.418] decompressing blob (type 1)...
[0002.451] display_resolution: No display init
[0002.456] Failed to retrieve display resolution
[0002.460] Could not load/initialize BMP blob...ignoring
[0002.511] decompressor handler not found
[0002.515] load_firmware_blob: Firmware blob loaded, entries=2
[0002.521] -------> se_aes_verify_sbk_clear: 747
[0002.525] se_aes_verify_sbk_clear: Error
[0002.529] bl_battery_charging: connected to external power supply
[0002.537] xusb is supported
[0002.543] error while finding nvidia,portmap
[0003.047] xusb blob version 0 size 124416
[0003.051] firmware size 124416
[0003.056] Firmware timestamp: 0x5da88fc3, Version: 50.25 release
[0003.063] xhci0: 64 bytes context size, 32-bit DMA
[0003.103] usbus0: 5.0Gbps Super Speed USB v3.0
[0003.123] uhub0: <Nvidia XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
[0003.773] uhub0: 9 ports with 9 removable, self powered
[0004.773] failed to get HID devices
[0004.776] failed to init xhci or no usb device attached
[0004.784] display_console_ioctl: No display init
[0004.788] switch_backlight failed
[0004.794] device_query_partition_size: failed to open partition sd0:MSC !
[0004.801] MSC Partition not found
[0004.807] device_query_partition_size: failed to open partition sd0:USP !
[0004.814] USP partition read failed!
[0004.818] blob_init: blob-partition USP header read failed
[0004.823] android_boot Unable to update recovery partition
[0004.829] kfs_getpartname: name = LNX
[0004.832] Loading kernel from LNX
[0004.930] load kernel from storage
[0004.942] decompressor handler not found
[0004.999] Successfully loaded kernel and ramdisk images
[0005.006] display_resolution: No display init
[0005.010] Failed to retrieve display resolution
[0005.015] bmp blob is not loaded and initialized
[0005.019] Failed to display boot-logo
[0005.023] NCK carveout not present
[0005.026] Skipping dts_overrides
[0005.029] NCK carveout not present
[0005.039] Find /i2c@7000c000's alias i2c0
[0005.043] get eeprom at 1-a0, size 256, type 0
[0005.052] Find /i2c@7000c500's alias i2c2
[0005.056] get eeprom at 3-a0, size 256, type 0
[0005.060] get eeprom at 3-ae, size 256, type 0
[0005.065] pm_ids_update: Updating 1,a0, size 256, type 0
[0005.070] I2C slave not started
[0005.073] I2C write failed
[0005.075] Writing offset failed
[0005.079] eeprom_init: EEPROM read failed
[0005.082] pm_ids_update: eeprom init failed
[0005.087] pm_ids_update: Updating 3,a0, size 256, type 0
[0005.117] pm_ids_update: The pm board id is 3448-0000-200
[0005.123] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0005.131] pm_ids_update: pm id update successful
[0005.136] pm_ids_update: Updating 3,ae, size 256, type 0
[0005.166] pm_ids_update: The pm board id is 3449-0000-200
[0005.172] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0005.180] pm_ids_update: pm id update successful
[0005.211] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0005.217] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0005.225] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0005.231] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0005.239] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e6:53:41
[0005.246] Plugin Manager: Parse ODM data 0x00094000
[0005.256] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0   
[0005.271] Add serial number:1422419088143 as DT property
[0005.280] "bpmp" doesn't exist, creating 
[0005.285] Updated bpmp info to DTB
[0005.290] Updated initrd info to DTB
[0005.294] "proc-board" doesn't exist, creating 
[0005.299] Updated board info to DTB
[0005.303] "pmu-board" doesn't exist, creating 
[0005.308] Updated board info to DTB
[0005.311] "display-board" doesn't exist, creating 
[0005.317] Updated board info to DTB
[0005.320] "reset" doesn't exist, creating 
[0005.325] Updated reset info to DTB
[0005.328] display_console_ioctl: No display init
[0005.333] display_console_ioctl: No display init
[0005.337] display_console_ioctl: No display init
[0005.342] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 
[0005.376] DTB cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0   
[0005.388] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 
[0005.401] Updated bootarg info to DTB
[0005.405] Adding uuid 00000001644495821c00000011fd8280 to DT
[0005.411] Adding eks info 0 to DT
[0005.416] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7
[0005.422] Updated memory info to DTB
[0005.428] Updated system-lp0-disable info to DTB
[0005.436] set vdd_core voltage to 1075 mv
[0005.440] setting 'vdd-core' regulator to 1075000 micro volts
[0005.463] Found secure-pmc; disable BPMP


U-Boot 2016.07-g0536cf2a27 (Dec 09 2019 - 22:40:32 -0800)

TEGRA210
Model: NVIDIA P3450-Porg
Board: NVIDIA P3450-PORG
DRAM:  4 GiB
MMC:   Tegra SD/MMC: 0, Tegra SD/MMC: 1
SF: Detected MX25U3235F with page size 256 Bytes, erase size 4 KiB, total 4 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Hit any key to stop autoboot:  1  0 
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/extlinux.conf
728 bytes read in 174 ms (3.9 KiB/s)
1:primary kernel
Retrieving file: /boot/initrd
5487751 bytes read in 542 ms (9.7 MiB/s)
Retrieving file: /boot/Image
34191368 bytes read in 2934 ms (11.1 MiB/s)
append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000  root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0    root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 
## Flattened Device Tree blob at 83100000
   Booting using the fdt blob at 0x83100000
   reserving fdt memory region: addr=80000000 size=20000
   Using Device Tree in place at 0000000083100000, end 00000000831776f0

Starting kernel ...

<hit enter to activate fiq debugger>
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.9.140-tegra (buildbrain@mobile-u64-2713) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Mon Dec 9 22:47:42 PST 2019
[    0.000000] Boot CPU: AArch64 Processor [411fd071]
[    0.000000] OF: fdt:memory scan node memory@80000000, reg size 48,
[    0.000000] OF: fdt: - 80000000 ,  7ee00000
[    0.000000] OF: fdt: - 100000000 ,  7f200000
[    0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB
[    0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB
[    0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB
[    0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB
[    0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout
[    0.000000] OF: reserved mem: initialized node iram-carveout, compatible id nvidia,iram-carveout
[    0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops
[    0.000000] cma: Reserved 64 MiB at 0x00000000fac00000
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.1
[    0.000000] percpu: Embedded 25 pages/cpu @ffffffc0fefb1000 s61592 r8192 d32616 u102400
[    0.000000] CPU features: enabling workaround for ARM erratum 832075
[    0.000000] Speculative Store Bypass Disable mitigation not required
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 1023544
[    0.000000] Kernel command line: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000  root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0    root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 
[    0.000000] log_buf_len individual max cpu contribution: 32768 bytes
[    0.000000] log_buf_len total cpu_extra contributions: 98304 bytes
[    0.000000] log_buf_len min size: 32768 bytes
[    0.000000] log_buf_len: 131072 bytes
[    0.000000] early log buf free: 29504(90%)
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.000000] Memory: 3570416K/4159488K available (15230K kernel code, 2926K rwdata, 6620K rodata, 8576K init, 609K bss, 113936K reserved, 475136K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)
[    0.000000]     vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000   (   250 GB)
[    0.000000]       .text : 0xffffff8008080000 - 0xffffff8008f60000   ( 15232 KB)
[    0.000000]     .rodata : 0xffffff8008f60000 - 0xffffff80095e0000   (  6656 KB)
[    0.000000]       .init : 0xffffff80095e0000 - 0xffffff8009e40000   (  8576 KB)
[    0.000000]       .data : 0xffffff8009e40000 - 0xffffff800a11b808   (  2927 KB)
[    0.000000]        .bss : 0xffffff800a11b808 - 0xffffff800a1b3dbc   (   610 KB)
[    0.000000]     fixed   : 0xffffffbefe7fd000 - 0xffffffbefec00000   (  4108 KB)
[    0.000000]     PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000   (    16 MB)
[    0.000000]     vmemmap : 0xffffffbf00000000 - 0xffffffc000000000   (     4 GB maximum)
[    0.000000]               0xffffffbf00000000 - 0xffffffbf03fc8000   (    63 MB actual)
[    0.000000]     memory  : 0xffffffc000000000 - 0xffffffc0ff200000   (  4082 MB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] Build-time adjustment of leaf fanout to 64.
[    0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[    0.000000] NR_IRQS:64 nr_irqs:64 0
[    0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller
[    0.000000] t210 clock and reset probe
[    0.000000] tegra-pmc: get_secure_pmc_setting: done secure_pmc=1
[    0.000000] clk_cbus_recalc_rate: no gbus parent
[    0.000000] clk_cbus_recalc_rate: no gbus parent
[    0.000000] clk_cbus_recalc_rate: no gbus parent
[    0.000000] clk_cbus_recalc_rate: no gbus parent
[    0.000000] clk_cbus_recalc_rate: no gbus parent
[    0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[    0.000006] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[    0.001769] Console: colour dummy device 80x25
[    0.002606] console [tty0] enabled
[    0.002633] kmemleak: Kernel memory leak detector disabled
[    0.002664] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800)
[    0.002694] pid_max: default: 32768 minimum: 301
[    0.003154] Security Framework initialized
[    0.003387] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.003408] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.004609] ftrace: allocating 47001 entries in 184 pages
[    0.176330] ASID allocator initialised with 65536 entries
[    0.216016] tegra-id: chipid=22117.
[    0.216059] tegra-id: opt_subrevision=0.
[    0.216088] Tegra Speedo/IDDQ fuse revision 4
[    0.216104] Tegra: CPU Speedo ID 9, SoC Speedo ID 0, GPU Speedo ID 2
[    0.216121] Tegra: CPU Process ID 0, SoC Process ID 1, GPU Process ID 0
[    0.216137] Tegra: CPU Speedo Value 2084, SoC Speedo Value 1976, GPU Speedo Value 2075
[    0.216158] Tegra: CPU IDDQ Value 1872, SoC IDDQ Value 1980, GPU IDDQ Value 2430
[    0.216195] Tegra Revision: A02 SKU: 0x8f CPU Process: 0 SoC Process: 1
[    0.216221] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0000-p3449-0000-a02.dts
[    0.216293] DTB Build time: Dec  9 2019 22:51:54
[    0.265044] CPU1: Booted secondary processor [411fd071]
[    0.296992] CPU2: Booted secondary processor [411fd071]
[    0.328957] CPU3: Booted secondary processor [411fd071]
[    0.329043] Brought up 4 CPUs
[    0.329108] SMP: Total of 4 processors activated.
[    0.329127] CPU features: detected feature: 32-bit EL0 Support
[    0.329399] CPU: All CPU(s) started at EL2
[    0.329430] alternatives: patching kernel code
[    0.337478] devtmpfs: initialized
[    0.374729] Initilizing CustomIPI irq domain
[    0.375153] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.375197] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.385701] pinctrl core: initialized pinctrl subsystem
[    0.386395] OS set in device tree is not L4T.
[    0.386799] regulator-dummy: no parameters
[    0.387101] Initializing plugin-manager
[    0.387230] Plugin module not found
[    0.387480] node /plugin-manager/fragement@0 match with board >=3448-0000-100
[    0.388040] node /plugin-manager/fragment@1 match with board >=3448-0000-101
[    0.388926] node /plugin-manager/fragment@5 match with board 3449-0000-200
[    0.389426] node /plugin-manager/fragement@6 match with odm-data enable-tegra-wdt
[    0.389874] node /plugin-manager/fragement@8 match with odm-data enable-tegra-wdt
[    0.390280] node /plugin-manager/fragement@9 match with board <3448-0000-300
[    0.395027] NET: Registered protocol family 16
[    0.399728] pstore: using zlib compression
[    0.400399] console [pstore-1] enabled
[    0.400417] pstore: Registered ramoops as persistent store backend
[    0.400435] ramoops: attached 0x200000@0xb0000000, ecc: 0/0
[    0.417060] cpuidle: using governor menu
[    0.421457] tegra_smmu 70019000.iommu: Loaded Tegra IOMMU driver
[    0.423085] vdso: 2 pages (1 code @ ffffff8008f67000, 1 data @ ffffff8009e44000)
[    0.423130] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.425515] atomic_pool_init():622: DMA: preallocated 1024 KiB pool for atomic allocations
[    0.428125] tegra_powergate_init: DONE
[    0.428165] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0000-p3449-0000-a02.dts
[    0.428203] DTB Build time: Dec  9 2019 22:51:54
[    0.430014] Tegra reboot handler registered.
[    0.434523] iommu: Adding device tegra-carveouts to group 0
[    0.434694] platform tegra-carveouts: domain=ffffffc0f9bbe318 allocates as[0]=ffffffc0f9bd80a8
[    0.435074] iommu: Adding device smmu_test to group 1
[    0.435142] platform smmu_test: domain=ffffffc0f9bbe558 allocates as[0]=ffffffc0f9bd8110
[    0.435960] mc: mapped MMIO address: 0xffffff800802e000 -> 0x70019000
[    0.436046] mc: mapped MMIO address: 0xffffff8008065000 -> 0x7001c000
[    0.436115] mc: mapped MMIO address: 0xffffff8008079000 -> 0x7001d000
[    0.436138] nv-tegra-mc 70019000.mc: No mssnvlink node
[    0.436173] mc-err: mcerr ops are set to t21x
[    0.445950] iommu: Adding device 70090000.xusb to group 2
[    0.446287] iommu: Adding device 70006000.serial to group 3
[    0.446368] platform 70006000.serial: domain=ffffffc0f944ec18 allocates as[0]=ffffffc0f9bd8178
[    0.446820] iommu: Adding device 70006040.serial to group 4
[    0.447086] iommu: Adding device 70006200.serial to group 5
[    0.447297] iommu: Adding device sound to group 6
[    0.447369] platform sound: domain=ffffffc0f94ba198 allocates as[0]=ffffffc0f9bd81e0
[    0.447946] iommu: Adding device 7000d400.spi to group 7
[    0.448225] iommu: Adding device 7000d600.spi to group 8
[    0.448563] iommu: Adding device 70410000.spi to group 9
[    0.448889] iommu: Adding device 50000000.host1x to group 10
[    0.449220] iommu: Adding device 54080000.vi to group 11
[    0.449652] iommu: Adding device 54600000.isp to group 12
[    0.449939] iommu: Adding device 54680000.isp to group 13
[    0.450234] iommu: Adding device tegradc.0 to group 14
[    0.450294] platform tegradc.0: domain=ffffffc0f94c60d8 allocates as[0]=ffffffc0f9bd8248
[    0.450831] platform tegradc.0: IOVA linear map 0x00000000d7000000(19000000)
[    0.451161] iommu: Adding device tegradc.1 to group 15
[    0.451226] platform tegradc.1: domain=ffffffc0f94c6318 allocates as[0]=ffffffc0f9bd82b0
[    0.451746] platform tegradc.1: IOVA linear map 0x00000000d7000000(19000000)
[    0.452034] iommu: Adding device 54340000.vic to group 16
[    0.452257] iommu: Adding device 544c0000.nvenc to group 17
[    0.452478] iommu: Adding device 54500000.tsec to group 18
[    0.452691] iommu: Adding device 54100000.tsecb to group 19
[    0.452905] iommu: Adding device 54480000.nvdec to group 20
[    0.453136] iommu: Adding device 54380000.nvjpg to group 21
[    0.454253] iommu: Adding device 546c0000.i2c to group 22
[    0.454606] iommu: Adding device 57000000.gpu to group 23
[    0.454677] platform 57000000.gpu: domain=ffffffc0f94d1318 allocates as[0]=ffffffc0f9bd8318
[    0.454752] platform 57000000.gpu: domain=ffffffc0f94d1318 allocates as[1]=ffffffc0f9bd8380
[    0.454811] platform 57000000.gpu: domain=ffffffc0f94d1318 allocates as[2]=ffffffc0f9bd83e8
[    0.454862] platform 57000000.gpu: domain=ffffffc0f94d1318 allocates as[3]=ffffffc0f9bd8450
[    0.455741] tegra-pmc 7000e400.pmc: i2c-thermtrip node not found, emergency thermal reset disabled.
[    0.455781] tegra-pmc 7000e400.pmc: scratch reg offset dts data not present
[    0.455809] tegra-pmc: ### PMC reset source: TEGRA_SOFTWARE_RESET
[    0.455829] tegra-pmc: ### PMC reset level: TEGRA_RESET_LEVEL_WARM
[    0.455847] tegra-pmc: ### PMC reset status reg: 0x3
[    0.505240] padctrl padctrl.0: Pad control driver tegra-pmc-padctrl registered
[    0.505272] tegra-pmc: Clear bootloader IO dpd settings
[    0.505305] tegra-pmc 7000e400.pmc: IO padctrl driver initialized
[    0.505383] tegra-pmc 7000e400.pmc: PMC: Successfully configure bootrom reset commands
[    0.505692] iommu: Adding device 70012000.se to group 24
[    0.506562] iommu: Adding device 7000c000.i2c to group 25
[    0.506903] iommu: Adding device 7000c400.i2c to group 26
[    0.507232] iommu: Adding device 7000c500.i2c to group 27
[    0.507565] iommu: Adding device 7000c700.i2c to group 28
[    0.507893] iommu: Adding device 7000d000.i2c to group 29
[    0.508222] iommu: Adding device 7000d100.i2c to group 30
[    0.508554] iommu: Adding device sdhci-tegra.0 to group 31
[    0.508630] platform sdhci-tegra.0: domain=ffffffc0f9574498 allocates as[0]=ffffffc0f9bd84b8
[    0.509714] iommu: Adding device 700d0000.xudc to group 32
[    0.514095] vdd-ac-bat: 5000 mV 
[    0.514547] vdd-5v0-sys: 5000 mV 
[    0.515717] vdd-5v0-hdmi: supplied by vdd-5v0-sys
[    0.515782] vdd-5v0-hdmi: 5000 mV 
[    0.516338] vdd-1v8-sys: 1800 mV 
[    0.516807] vdd-fan: supplied by vdd-5v0-sys
[    0.516863] vdd-fan: 5000 mV 
[    0.517390] vdd-usb-vbus: supplied by vdd-5v0-sys
[    0.517442] vdd-usb-vbus: 5000 mV 
[    0.518029] vdd-usb-vbus2: 5000 mV 
[    0.553958] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.556341] gpio gpiochip0: gpio-line-names specifies 240 line names but there are 256 lines on the chip
[    0.557501] GPIO line 151 (camera-control-output-low) hogged as output/low
[    0.557539] GPIO line 152 (camera-control-output-low) hogged as output/low
[    0.557918] gpiochip_setup_dev: registered GPIOs 0 to 255 on device: gpiochip0 (tegra-gpio)
[    0.565755] eventlib_kernel: keventlib is initialized, test id: 0
[    0.566124] SCSI subsystem initialized
[    0.566631] usbcore: registered new interface driver usbfs
[    0.566707] usbcore: registered new interface driver hub
[    0.566797] usbcore: registered new device driver usb
[    0.570673] max77620 4-003c: PMIC Version OTP:0x35 and ES:0x8
[    0.577119] random: fast init done
[    0.577129] vdd-core: 600 <--> 1162 mV at 1075 mV 
[    0.578062] vdd-ddr-1v1: Bringing 1125000uV into 1150000-1150000uV
[    0.581018] vdd-ddr-1v1: 1150 mV 
[    0.585010] vdd-pre-reg-1v35: 1350 mV 
[    0.589011] vdd-1v8: 1800 mV 
[    0.593009] avdd-sys-1v2: 1200 mV 
[    0.597009] vdd-pex-1v0: 1050 mV 
[    0.597681] vddio-sdmmc-ap: 1800 <--> 3300 mV at 3300 mV 
[    0.598222] max77620-ldo3: at 3100 mV 
[    0.601008] vdd-rtc: 850 <--> 1100 mV at 1000 mV 
[    0.601557] max77620-ldo5: at 3100 mV 
[    0.602110] max77620-ldo6: at 2800 mV 
[    0.605012] avdd-1v05-pll: 1050 mV 
[    0.609008] avdd-io-hdmi-dp: 1050 mV 
[    0.611501] GPIO line 505 (spmic-default-output-high) hogged as output/high
[    0.611798] gpiochip_setup_dev: registered GPIOs 504 to 511 on device: gpiochip1 (max77620-gpio)
[    0.612105] max77620 4-003c: max77620 probe successful
[    0.614820] media: Linux media interface: v0.10
[    0.614897] Linux video capture interface: v2.00
[    0.615805] pps_core: LinuxPPS API ver. 1 registered
[    0.615835] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.615877] PTP clock support registered
[    0.619559] tegra_fiq_debugger_init: found FIQ source (IRQ 98)
[    0.625867] tegra210-emc 7001b000.external-memory-controller: validated EMC DFS table
[    0.626667] Advanced Linux Sound Architecture Driver Initialized.
[    0.627324] Bluetooth: Core ver 2.22
[    0.627396] NET: Registered protocol family 31
[    0.627415] Bluetooth: HCI device and connection manager initialized
[    0.627445] Bluetooth: HCI socket layer initialized
[    0.627467] Bluetooth: L2CAP socket layer initialized
[    0.627505] Bluetooth: SCO socket layer initialized
[    0.629222] tegra210_dvfs: no clock found for sdmmc2_ddr
[    0.629261] tegra210_dvfs: no clock found for sdmmc4_ddr
[    0.629320] tegra210_dvfs: no clock found for sdmmc1_ddr
[    0.629349] tegra210_dvfs: no clock found for sdmmc3_ddr
[    0.632631] tegra_dvfs: Unable to get vdd-cpu rail for step info, defering probe
[    0.633946] vdd-3v3-sys: supplied by vdd-5v0-sys
[    0.634055] vdd-3v3-sys: 3300 mV 
[    0.634328] vdd-1v8-sys: supplied by vdd-3v3-sys
[    0.637076] vdd-usb-vbus2: supplied by vdd-3v3-sys
[    0.637548] vdd-3v3-sd: supplied by vdd-3v3-sys
[    0.637600] vdd-3v3-sd: 3300 mV 
[    0.638478] avdd-io-edp-1v05: supplied by avdd-1v05-pll
[    0.638540] avdd-io-edp-1v05: 1050 mV 
[    0.639026] vdd-usb-hub-en: supplied by vdd-1v8-sys
[    0.639078] vdd-usb-hub-en: 5000 mV 
[    0.640340] camchar: rtcpu character device driver loaded
[    0.641066] extcon-gpio-states extcon:extcon@1: Cable state:1, cable id:1
[    0.642464] clocksource: Switched to clocksource arch_sys_counter
[    0.682222] VFS: Disk quotas dquot_6.6.0
[    0.682389] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.682949] nvmap_heap_init: nvmap_heap_init: created heap block cache
[    0.683390] dma_declare_coherent_resizable_cma_memory:324: resizable heap=vpr, base=0x00000000d7000000, size=0x19000000
[    0.683436]  dma-vpr: heap size is not multiple of cma_chunk_size heap_info->num_chunks (13) rem_chunk_size(0x1000000)
[    0.683654] cma: enabled page replacement for spfn=d7000, epfn=f0000
[    0.683678] dma_declare_coherent_resizable_cma_memory:373: resizable cma heap=vpr create successful
[    0.683707] tegra-carveouts tegra-carveouts: assigned reserved memory node vpr-carveout
[    0.683754] tegra-carveouts tegra-carveouts: iram :dma coherent mem declare 0x0000000040001000,258048
[    0.683781] tegra-carveouts tegra-carveouts: assigned reserved memory node iram-carveout
[    0.683812] nvmap: nvmap_select_cache_ops() nvmap cache ops set to set/ways
[    0.683836] nvmap_page_pool_init: Total RAM pages: 1011388
[    0.683853] nvmap_page_pool_init: nvmap page pool size: 126423 pages (493 MB)
[    0.684020] nvmap_background_zero_thread: PP zeroing thread starting.
[    0.684369] misc nvmap: created heap iram base 0x0000000040001000 size (252KiB)
[    0.685199] misc nvmap: created heap vpr base 0x00000000d7000000 size (409600KiB)
[    0.693308] thermal thermal_zone0: Registering thermal zone thermal_zone0 for type AO-therm
[    0.693750] thermal thermal_zone1: Registering thermal zone thermal_zone1 for type CPU-therm
[    0.694044] thermal thermal_zone2: Registering thermal zone thermal_zone2 for type GPU-therm
[    0.694268] thermal thermal_zone3: Registering thermal zone thermal_zone3 for type PLL-therm
[    0.694489] thermal thermal_zone4: Registering thermal zone thermal_zone4 for type PMIC-Die
[    0.694775] pre_t19x_iso_plat_init(): iso emc max clk=1600000KHz
[    0.694796] pre_t19x_iso_plat_init(): max_iso_bw=11520000KB
[    0.695242] NET: Registered protocol family 2
[    0.696202] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[    0.696438] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[    0.696949] TCP: Hash tables configured (established 32768 bind 32768)
[    0.697113] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    0.697212] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    0.697654] NET: Registered protocol family 1
[    0.698508] RPC: Registered named UNIX socket transport module.
[    0.698541] RPC: Registered udp transport module.
[    0.698559] RPC: Registered tcp transport module.
[    0.698577] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.698860] Trying to unpack rootfs image as initramfs...
[    0.930743] Freeing initrd memory: 5356K
[    0.940719] host1x 50000000.host1x: initialized
[    0.942576] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[    0.945825] audit: initializing netlink subsys (disabled)
[    0.945940] audit: type=2000 audit(0.795:1): initialized
[    0.946750] workingset: timestamp_bits=46 max_order=20 bucket_order=0
[    0.956758] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.958252] ntfs: driver 2.1.32 [Flags: R/W].
[    0.959102] 9p: Installing v9fs 9p2000 file system support
[    0.962354] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 240)
[    0.962551] io scheduler noop registered
[    0.962864] io scheduler cfq registered (default)
[    0.965545] gic 702f9000.agic: GIC IRQ controller registered
[    0.968588] iommu: Adding device 702ef000.adsp to group 33
[    0.977800] iommu: Adding device aconnect@702c0000:adsp_audio to group 34
[    0.977980] tegra-aconnect aconnect@702c0000: Tegra ACONNECT bus registered
[    0.978616] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_SKU_CALIB_0 = 0x8229413
[    0.978651] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_USB_CALIB_EXT_0 = 0x4
[    0.980305] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.0, lane = usb2-0, function = xusb
[    0.980440] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.1, lane = usb2-1, function = xusb
[    0.980550] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.2, lane = usb2-2, function = xusb
[    0.980762] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.3, lane = pcie-0, function = pcie-x1
[    0.980882] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.4, lane = pcie-1, function = pcie-x4
[    0.980991] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.5, lane = pcie-2, function = pcie-x4
[    0.981106] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.6, lane = pcie-3, function = pcie-x4
[    0.981217] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.7, lane = pcie-4, function = pcie-x4
[    0.981328] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.8, lane = pcie-5, function = xusb
[    0.981439] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.9, lane = pcie-6, function = xusb
[    0.987730] tegra-pwm 7000a000.pwm: PWM clk cannot sleep in ops
[    0.989498] tegra-dfll-pwm 70110000.pwm: DFLL pwm-rate: 12800000
[    0.991518] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration
[    0.992807] tegra-pcie 1003000.pcie: PCIE: Enable power rails
[    0.993166] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes
[    0.994348] tegra_camera_platform tegra-camera-platform: tegra_camera_probe:camera_platform_driver probe
[    0.994630] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes
[    0.994954] misc tegra_camera_ctrl: tegra_camera_isomgr_register isp_iso_bw=1500000, vi_iso_bw=750000, max_bw=1500000
[    0.995223] Adding domain tsec-pd to PM domain host1x-pd
[    0.998407] tsec 54500000.tsec: initialized
[    0.999804] tsec 54100000.tsecb: initialized
[    1.000508] Adding domain nvdec-pd to PM domain host1x-pd
[    1.003901] nvdec 54480000.nvdec: initialized
[    1.004947] Adding domain vic03-pd to PM domain host1x-pd
[    1.005154] Adding domain msenc-pd to PM domain host1x-pd
[    1.005323] Adding domain nvjpg-pd to PM domain host1x-pd
[    1.009571] falcon 54340000.vic: initialized
[    1.010872] falcon 544c0000.nvenc: initialized
[    1.012208] falcon 54380000.nvjpg: initialized
[    1.016615] tegra_cec 70015000.tegra_cec: dt=1 start=0x70015000 end=0x70015FFF irq=97
[    1.016689] tegra_cec 70015000.tegra_cec: Enable clock result: 0.
[    1.016738] tegra_cec 70015000.tegra_cec: tegra_cec_init started
[    1.016848] tegradc tegradc.0: disp0 connected to head0->/host1x/sor1
[    1.016998] display board info: id 0x0, fab 0x0
[    1.017040] tegra_cec 70015000.tegra_cec: cec_add_sysfs ret=0
[    1.017062] tegra_cec 70015000.tegra_cec: probed
[    1.017077] generic_infoframe_type: 0x87
[    1.017219] tegradc tegradc.0: DT parsed successfully
[    1.017289] tegradc tegradc.0: Display dc.ffffff800ab40000 registered with id=0
[    1.024895] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels
[    1.025444] tegradc tegradc.0: probed
[    1.026185] Console: switching to colour frame buffer device 80x30
[    1.026238] tegradc tegradc.0: fb registered
[    1.027612] tegradc tegradc.1: disp1 connected to head1->/host1x/sor
[    1.027724] tegradc tegradc.1: No lt-data, using default setting
[    1.027765] tegradc tegradc.1: No hpd-gpio in DT
[    1.027809] tegradc tegradc.1: DT parsed successfully
[    1.027875] tegradc tegradc.1: Display dc.ffffff800acc0000 registered with id=1
[    1.029298] tegradc tegradc.1: dpd enable lookup fail:-19
[    1.031137] tegra-adma 702e2000.adma: Tegra210 ADMA driver registered 22 channels
[    1.031965] tegra-fuse-burn 7000f800.efuse:efuse-burn: Fuse burn driver initialized
[    1.032314] kfuse 7000fc00.kfuse: initialized
[    1.535507] Host read timeout at address 545c00c4
[    1.535639] tegra-pmc-iopower pmc-iopower: Regulator supply iopower-dbg-supply not available
[    1.536613] tegra-pmc-iopower pmc-iopower: NO_IOPOWER setting 0x0
[    1.536763] tegradc tegradc.1: probed
[    1.537156] tegradc tegradc.1: fb registered
[    1.537844] tegra-dfll-pwm 70110000.pwm: DFLL_PWM regulator is available now
[    1.537872] vdd-cpu: 708 <--> 1322 mV at 708 mV 
[    1.538265] pwm-regulator pwm_regulators:pwm-regulator@0: PWM regulator registration passed
[    1.539488] vdd-gpu: applied init 1000000uV constraint
[    1.539512] vdd-gpu: 708 <--> 1323 mV at 997 mV 
[    1.539907] pwm-regulator pwm_regulators:pwm-regulator@1: PWM regulator registration passed
[    1.540370] hpd: state 7 (Takeover from bootloader), hpd 0, pending_hpd_evt 1
[    1.540394] hpd: switching from state 7 (Takeover from bootloader) to state 0 (Reset)
[    1.540416] hpd: state 0 (Reset), hpd 0, pending_hpd_evt 0
[    1.540442] tegradc tegradc.1: blank - powerdown
[    1.540472] extcon-disp-state extcon:disp-state: cable 44 state 0 already set.
[    1.540490] Extcon DP: HPD disabled
[    1.540503] hpd: hpd_switch 0
[    1.540516] hpd: switching from state 0 (Reset) to state 1 (Check Plug)
[    1.540537] hpd: state 1 (Check Plug), hpd 0, pending_hpd_evt 0
[    1.540554] hpd: switching from state 1 (Check Plug) to state 3 (Disabled)
[    1.543613] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    1.543748] No Device Node present for smmu client: serial8250 !!
[    1.543771] platform serial8250: No iommus property found in DT node, got swgids from fixup(101004000)
[    1.543825] iommu: Adding device serial8250 to group 35
[    1.546078] console [ttyS0] disabled
[    1.546213] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 63, base_baud = 25500000) is a Tegra
[    1.921835] tegra-pcie 1003000.pcie: link 0 down, retrying
[    2.042490] tegra_cec 70015000.tegra_cec: Can't find physical addresse.
[    2.042494] tegra_cec 70015000.tegra_cec: tegra_cec_init Done.
[    2.326097] tegra-pcie 1003000.pcie: link 0 down, retrying
[    2.730358] tegra-pcie 1003000.pcie: link 0 down, retrying
[    2.732376] tegra-pcie 1003000.pcie: link 0 down, ignoring
[    2.838608] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00
[    2.838617] pci_bus 0000:00: root bus resource [io  0x0000-0xffff]
[    2.838622] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff]
[    2.838628] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref]
[    2.838637] pci_bus 0000:00: root bus resource [bus 00-ff]
[    2.839032] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    2.850628] pci 0000:00:02.0: BAR 14: assigned [mem 0x13000000-0x130fffff]
[    2.850634] pci 0000:00:02.0: BAR 13: assigned [io  0x1000-0x1fff]
[    2.850643] pci 0000:01:00.0: BAR 4: assigned [mem 0x13000000-0x13003fff 64bit]
[    2.850664] pci 0000:01:00.0: BAR 2: assigned [mem 0x13004000-0x13004fff 64bit]
[    2.850682] pci 0000:01:00.0: BAR 0: assigned [io  0x1000-0x10ff]
[    2.850694] pci 0000:00:02.0: PCI bridge to [bus 01]
[    2.850699] pci 0000:00:02.0:   bridge window [io  0x1000-0x1fff]
[    2.850706] pci 0000:00:02.0:   bridge window [mem 0x13000000-0x130fffff]
[    2.851115] pcieport 0000:00:02.0: Signaling PME through PCIe PME interrupt
[    2.851119] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
[    4.070584] console [ttyS0] enabled
[    4.075335] 70006040.serial: ttyTHS1 at MMIO 0x70006040 (irq = 64, base_baud = 0) is a TEGRA_UART
[    4.084535] serial-tegra 70006200.serial: RX in PIO mode
[    4.089977] 70006200.serial: ttyTHS2 at MMIO 0x70006200 (irq = 65, base_baud = 0) is a TEGRA_UART
[    4.099904] [drm] Initialized
[    4.112895] brd: module loaded
[    4.121388] loop: module loaded
[    4.124804] tegra_profiler: version: 1.139, samples/io: 47/27
[    4.130710] tegra_profiler: auth: init
[    4.135842] THERMAL EST: found 2 subdevs
[    4.139820] THERMAL EST num_resources: 0
[    4.143765] [THERMAL EST subdev 0]
[    4.147182] [THERMAL EST subdev 1]
[    4.151055] thermal thermal_zone5: Registering thermal zone thermal_zone5 for type thermal-fan-est
[    4.160036] THERMAL EST: thz register success.
[    4.164639] THERMAL EST: end of probe, return err: 0
[    4.170858] hisi_sas: driver version v1.6
[    4.179224] tegra-qspi 70410000.spi: Prod settings list not found
[    4.186612] qspi_mtd spi32766.0: MX25U3235F (4096 Kbytes)
[    4.192039] qspi_mtd spi32766.0: mtd .name = spi32766.0, .size = 0x400000 (4MiB) .erasesize = 0x00001000 (4KiB) .numeraseregions = 0
[    4.207010] libphy: Fixed MDIO Bus: probed
[    4.212044] tun: Universal TUN/TAP device driver, 1.6
[    4.217138] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    4.224308] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[    4.230169] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    4.236156] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
[    4.243128] igb: Copyright (c) 2007-2014 Intel Corporation.
[    4.248755] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k
[    4.256593] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
[    4.262566] Intel(R) 10GbE PCI Express Linux Network Driver - version 4.6.4
[    4.269537] Copyright(c) 1999 - 2017 Intel Corporation.
[    4.275614] r8168 0000:01:00.0: enabling device (0000 -> 0003)
[    4.281509] r8168 Gigabit Ethernet driver 8.045.08-NAPI loaded
[    4.301518] r8168 0000:01:00.0 (unnamed net_device) (uninitialized): Invalid ethernet address 00:00:00:00:00:00, trying device tree node
[    4.313947] r8168 0000:01:00.0 (unnamed net_device) (uninitialized): Found valid ethernet address 00:04:4b:e6:53:41 from device tree
[    4.326404] r8168: This product is covered by one or more of the following patents: US6,570,884, US6,115,776, and US6,327,625.
[    4.337856] r8168  Copyright (C) 2017  Realtek NIC software team <nicfae@realtek.com> 
[    4.337856]  This program comes with ABSOLUTELY NO WARRANTY; for details, please see <http://www.gnu.org/licenses/>. 
[    4.337856]  This is free software, and you are welcome to redistribute it under certain conditions; see <http://www.gnu.org/licenses/>. 
[    4.369221] PPP generic driver version 2.4.2
[    4.373704] PPP BSD Compression module registered
[    4.378436] PPP Deflate Compression module registered
[    4.383530] PPP MPPE Compression module registered
[    4.388337] NET: Registered protocol family 24
[    4.392860] usbcore: registered new interface driver r8152
[    4.398408] usbcore: registered new interface driver asix
[    4.403870] usbcore: registered new interface driver ax88179_178a
[    4.410008] usbcore: registered new interface driver cdc_ether
[    4.415882] usbcore: registered new interface driver net1080
[    4.421590] usbcore: registered new interface driver cdc_subset
[    4.427562] usbcore: registered new interface driver zaurus
[    4.433199] usbcore: registered new interface driver cdc_ncm
[    4.439023] VFIO - User Level meta-driver version: 0.3
[    4.445376] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.451941] ehci-pci: EHCI PCI platform driver
[    4.456444] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    4.462637] ohci-pci: OHCI PCI platform driver
[    4.467135] ohci-platform: OHCI generic platform driver
[    4.475039] tegra-xusb 70090000.xusb: USB2 port 0 has OTG_CAP
[    4.481403] tegra-xusb-padctl 7009f000.xusb_padctl: enabled OTG on UTMI pad 0
[    4.489738] tegra-xusb 70090000.xusb: extcon 0: ffffffc0f9068000 id
[    4.498187] usbcore: registered new interface driver uas
[    4.503578] tegra-xusb 70090000.xusb: Firmware timestamp: 2019-10-17 15:58:59 UTC, Version: 50.25 release
[    4.503647] tegra-xusb 70090000.xusb: xHCI Host Controller
[    4.503672] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 1
[    4.504422] tegra-xusb 70090000.xusb: hcc params 0x0184f525 hci version 0x100 quirks 0x00050010
[    4.504483] tegra-xusb 70090000.xusb: irq 61, io mem 0x70090000
[    4.504803] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    4.504809] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.504813] usb usb1: Product: xHCI Host Controller
[    4.504817] usb usb1: Manufacturer: Linux 4.9.140-tegra xhci-hcd
[    4.504821] usb usb1: SerialNumber: 70090000.xusb
[    4.514937] hub 1-0:1.0: USB hub found
[    4.514980] hub 1-0:1.0: 5 ports detected
[    4.515546] tegra-xusb 70090000.xusb: xHCI Host Controller
[    4.515559] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 2
[    4.515661] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    4.515759] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[    4.515764] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.515768] usb usb2: Product: xHCI Host Controller
[    4.515772] usb usb2: Manufacturer: Linux 4.9.140-tegra xhci-hcd
[    4.515775] usb usb2: SerialNumber: 70090000.xusb
[    4.516201] hub 2-0:1.0: USB hub found
[    4.516234] hub 2-0:1.0: 4 ports detected
[    4.618525] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 1
[    4.645575] usbcore: registered new interface driver usb-storage
[    4.651721] usbcore: registered new interface driver usbserial
[    4.661028] tegra-xudc-new 700d0000.xudc: device count: 1
[    4.667738] tegra-xudc-new 700d0000.xudc: USB charger detection disabled
[    4.674479] tegra-xudc-new 700d0000.xudc: vbus state: 1
[    4.679726] tegra-xudc-new 700d0000.xudc: device mode on: 0
[    4.685337] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 0
[    4.692052] tegra-xudc-new 700d0000.xudc: active: 0 => 1
[    4.698029] mousedev: PS/2 mouse device common for all mice
[    4.703716] usbcore: registered new interface driver xpad
[    4.819500] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0
[    4.829319] rtc rtc1: alarm rtc device
[    4.833121] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1
[    4.840290] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock
[    4.846477] usb 1-2: new high-speed USB device number 2 using tegra-xusb
[    4.853764] i2c /dev entries driver
[    4.859104] imx219 6-0010: tegracam sensor driver:imx219_v2.0.6
[    4.888413] tegra-vii2c 546c0000.i2c: no acknowledge from address 0x10
[    4.894985] usb 1-2: New USB device found, idVendor=0bda, idProduct=5411
[    4.894990] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    4.894994] usb 1-2: Product: 4-Port USB 2.1 Hub
[    4.895000] usb 1-2: Manufacturer: Generic
[    4.909052] hub 1-2:1.0: USB hub found
[    4.913558] hub 1-2:1.0: 4 ports detected
[    4.925587] imx219 6-0010: imx219_board_setup: error during i2c read probe (-121)
[    4.933141] imx219 6-0010: board setup failed
[    4.937729] imx219: probe of 6-0010 failed with error -121
[    4.944268] max77620-power max77620-power: Event recorder REG_NVERC : 0x0
[    4.953736] tegra_soctherm 700e2000.soctherm: pllx_offset tz:0 max:14, min:2
[    4.960815] tegra_soctherm 700e2000.soctherm: pllx_offset tz:2 max:8, min:4
[    4.968222] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[    4.977570] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when cpu reaches 102500 mC
[    4.986579] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when cpu reaches 100500 mC
[    4.995602] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[    5.004926] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when gpu reaches 103000 mC
[    5.013898] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when gpu reaches 101000 mC
[    5.022934] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[    5.032253] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when pll reaches 127000 mC
[    5.041220] tegra_soctherm 700e2000.soctherm: throttrip: pll: missing hot temperature
[    5.049436] tegra_soctherm 700e2000.soctherm: failed to register sensor: -19
[    5.057352] tegra_aotag tegra-aotag: Registering sensor 0
[    5.062860] tegra_aotag tegra-aotag: Bound to TZ : ID 0
[    5.068112] tegra_aotag tegra-aotag: Probe done [SUCCESS]:0
[    5.074655] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[    5.083986] tegra_dfll_action dfll-cdev-cap: Tegra DFLL 'cap cooling device' registered
[    5.092226] tegra_dfll_action dfll-cdev-floor: Tegra DFLL 'floor cooling device' registered
[    5.101013] parse_throttle_dt_data: Num cap clks = 6
[    5.105999] parse_throttle_dt_data: clk=cclk_g type=2
[    5.111069] parse_throttle_dt_data: clk=gpu type=4
[    5.115894] parse_throttle_dt_data: clk=cap.throttle.c2bus type=0
[    5.122010] parse_throttle_dt_data: clk=cap.throttle.c3bus type=0
[    5.128131] parse_throttle_dt_data: clk=cap.throttle.sclk type=0
[    5.134143] parse_throttle_dt_data: clk=emc type=3
[    5.139312] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[    5.148728] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[    5.158199] tegra_throttle_probe: probe successful. #cdevs=4
[    5.164750] FAN dev name: pwm-fan
[    5.168224] FAN:gpio request success.
[    5.171963] pwm_fan_driver pwm-fan: cap state:7, cap pwm:255
[    5.177972] pwm_fan_driver pwm-fan: got pwm for fan. polarity is normal
[    5.184779] pwm_fan_driver pwm-fan: fan tach request irq success
[    5.190854] pwm_fan_driver pwm-fan: tach period: 1000
[    5.196045] pwm_fan_driver pwm-fan: index 0: pwm=0, rpm=0, rru=40, rrd=40, state:2
[    5.203625] pwm_fan_driver pwm-fan: index 1: pwm=80, rpm=1000, rru=2, rrd=2, state:2
[    5.211377] pwm_fan_driver pwm-fan: index 2: pwm=120, rpm=2000, rru=1, rrd=1, state:2
[    5.219211] pwm_fan_driver pwm-fan: index 3: pwm=160, rpm=3000, rru=1, rrd=1, state:2
[    5.227048] pwm_fan_driver pwm-fan: index 4: pwm=255, rpm=4000, rru=1, rrd=1, state:3
[    5.234882] pwm_fan_driver pwm-fan: index 5: pwm=255, rpm=5000, rru=1, rrd=1, state:3
[    5.242719] pwm_fan_driver pwm-fan: index 6: pwm=255, rpm=6000, rru=1, rrd=1, state:3
[    5.250555] pwm_fan_driver pwm-fan: index 7: pwm=255, rpm=7000, rru=1, rrd=1, state:4
[    5.254483] usb 1-2.1: new low-speed USB device number 3 using tegra-xusb
[    5.265193] pwm_fan_driver pwm-fan: index 8: pwm=255, rpm=10000, rru=1, rrd=1, state:4
[    5.273121] pwm_fan_driver pwm-fan: index 9: pwm=255, rpm=11000, rru=1, rrd=1, state:4
[    5.281786] tegra-wdt 60005100.watchdog: Tegra WDT enabled on probe. Timeout = 120 seconds.
[    5.290565] tegra-wdt 60005100.watchdog: initialized (timeout = 120 sec, nowayout = 1)
[    5.299438] device-mapper: uevent: version 1.0.3
[    5.304598] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com
[    5.315340] usb 1-2.1: New USB device found, idVendor=040b, idProduct=2000
[    5.318513] tegra210-cpufreq cpufreq: probe()...completed
[    5.319206] sdhci: Secure Digital Host Controller Interface driver
[    5.319208] sdhci: Copyright(c) Pierre Ossman
[    5.319209] sdhci-pltfm: SDHCI platform and OF driver helper
[    5.319683] sdhci-tegra sdhci-tegra.0: Got CD GPIO
[    5.320025] sdhci-tegra sdhci-tegra.0: Client registration for eMC Successful
[    5.320148] sdhci-tegra sdhci-tegra.0: wakeup init done, cdirq 300
[    5.334177] tegra-se 70012000.se: tegra_se_probe: complete
[    5.334706] hidraw: raw HID events driver (C) Jiri Kosina
[    5.336076] usbcore: registered new interface driver usbhid
[    5.336078] usbhid: USB HID core driver
[    5.338162] tegra21x_actmon 6000c800.actmon: in actmon_register()...
[    5.338325] tegra21x_actmon 6000c800.actmon: initialization Completed for the device mc_all
[    5.340140] nvpmodel: initialized successfully
[    5.341222] usbcore: registered new interface driver snd-usb-audio
[    5.341276] No Device Node present for smmu client: snd-soc-dummy !!
[    5.341280] platform snd-soc-dummy: No iommus property found in DT node, got swgids from fixup(101004000)
[    5.341296] iommu: Adding device snd-soc-dummy to group 36
[    5.346822] input: tegra-hda HDMI/DP,pcm=3 as /devices/70030000.hda/sound/card0/input0
[    5.368660] OPE platform probe
[    5.368738] OPE platform probe successful
[    5.369062] OPE platform probe
[    5.369144] OPE platform probe successful
[    5.370677] mmc0: SDHCI controller on sdhci-tegra.0 [sdhci-tegra.0] using ADMA 64-bit with 64 bit addr
[    5.395289] tegra-asoc: sound: ADMAIF1 <-> ADMAIF1 mapping ok
[    5.395416] tegra-asoc: sound: ADMAIF2 <-> ADMAIF2 mapping ok
[    5.395533] tegra-asoc: sound: ADMAIF3 <-> ADMAIF3 mapping ok
[    5.395651] tegra-asoc: sound: ADMAIF4 <-> ADMAIF4 mapping ok
[    5.395774] tegra-asoc: sound: ADMAIF5 <-> ADMAIF5 mapping ok
[    5.395894] tegra-asoc: sound: ADMAIF6 <-> ADMAIF6 mapping ok
[    5.396010] tegra-asoc: sound: ADMAIF7 <-> ADMAIF7 mapping ok
[    5.396141] tegra-asoc: sound: ADMAIF8 <-> ADMAIF8 mapping ok
[    5.396258] tegra-asoc: sound: ADMAIF9 <-> ADMAIF9 mapping ok
[    5.396377] tegra-asoc: sound: ADMAIF10 <-> ADMAIF10 mapping ok
[    5.407600] u32 classifier
[    5.407602]     Actions configured
[    5.407671] Initializing XFRM netlink socket
[    5.408381] NET: Registered protocol family 10
[    5.409121] NET: Registered protocol family 17
[    5.409132] NET: Registered protocol family 15
[    5.409206] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    5.409248] Bluetooth: RFCOMM socket layer initialized
[    5.409256] Bluetooth: RFCOMM ver 1.11
[    5.409261] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    5.409265] Bluetooth: HIDP socket layer initialized
[    5.409283] 9pnet: Installing 9P2000 support
[    5.409317] Key type dns_resolver registered
[    5.414119] Registered cp15_barrier emulation handler
[    5.414126] Registered setend emulation handler
[    5.415183] registered taskstats version 1
[    5.415761] Adding domain ve2-pd to PM domain host1x-pd
[    5.415999] Adding domain ve-pd to PM domain host1x-pd
[    5.418046] isp 54600000.isp: initialized
[    5.418994] isp 54680000.isp: initialized
[    5.428814] mmc0: new SDHC card at address 0001
[    5.428958] last reset is due to software reset
[    5.428961] KERNEL: PMC reset status reg: 0x3
[    5.429053] BL: PMC reset status reg: 0x3
[    5.429054] BL: PMIC poweroff Event Recorder: 0x0
[    5.429216] mmcblk0: mmc0:0001 SD16G 29.8 GiB 
[    5.430482] clk_cbus_recalc_rate: no gbus parent
[    5.430486] clk_cbus_round_rate: no gbus parent
[    5.430487] clk_cbus_round_rate: no gbus parent
[    5.430494] clk_cbus_recalc_rate: no gbus parent
[    5.430594] clk_cbus_recalc_rate: no gbus parent
[    5.430596] clk_cbus_round_rate: no gbus parent
[    5.430598] clk_cbus_round_rate: no gbus parent
[    5.430601] clk_cbus_recalc_rate: no gbus parent
[    5.430614] tegra_dvfs: GPU-cap: registered
[    5.430671] tegra dvfs: vdd-cpu: nominal 1168mV, offset 708000uV, step 19200uV, scaling enabled
[    5.430673] tegra dvfs: vdd-core: nominal 1075mV, offset 600000uV, step 12500uV, scaling enabled
[    5.430675] tegra dvfs: vdd-gpu: nominal 1058mV, offset 708000uV, step 10000uV, scaling enabled
[    5.432059] tegra_dvfs: vdd-gpu-vts: registered
[    5.432714] tegra_core_action core_dvfs_cdev_floor: Tegra CORE DVFS 'floor cooling device' registered
[    5.433309] tegra_core_action core_dvfs_cdev_cap: Tegra CORE DVFS 'cap cooling device' registered
[    5.433794] input: gpio-keys as /devices/gpio-keys/input/input1
[    5.466289] tegra_rtc 7000e000.rtc: setting system clock to 2000-01-01 01:30:34 UTC (946690234)
[    5.467310] vi 54080000.vi: vi_probe: ++
[    5.470057] vi 54080000.vi: initialized
[    5.472005] vi 54080000.vi: subdev nvcsi--1 bound
[    5.472219] mmcblk mmc0:0001: Card claimed for testing.
[    5.473451] Disable partitions left on by BL
[    5.473453]   disb
[    5.473493] bwmgr: missing cdev-type property
[    5.473582] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[    5.473587] DRAM derating cdev registered.
[    5.474570] vdd-fan: disabling
[    5.474572] vdd-usb-vbus: disabling
[    5.474574] vdd-usb-vbus2: disabling
[    5.474583] avdd-io-edp-1v05: disabling
[    5.474678] ALSA device list:
[    5.474680]   #0: tegra-hda at 0x70038000 irq 83
[    5.474682]   #1: tegra-snd-t210ref-mobile-rt565x
[    5.599312]  mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14
[    5.819924] usb 1-2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    5.819928] usb 1-2.1: Product: USB Keyboard
[    5.819930] usb 1-2.1: Manufacturer: Generic
[    5.824695] input: Generic USB Keyboard as /devices/70090000.xusb/usb1/1-2/1-2.1/1-2.1:1.0/0003:040B:2000.0001/input/input2
[    5.849990] Freeing unused kernel memory: 8576K
[    5.874808] Root device found: mmcblk0p1
[    5.879818] Found dev node: /dev/mmcblk0p1
[    5.884360] hid-generic 0003:040B:2000.0001: input,hidraw0: USB HID v1.10 Keyboard [Generic USB Keyboard] on usb-70090000.xusb-2.1/input0
[    5.902810] input: Generic USB Keyboard as /devices/70090000.xusb/usb1/1-2/1-2.1/1-2.1:1.1/0003:040B:2000.0002/input/input3
[    5.971035] hid-generic 0003:040B:2000.0002: input,hidraw1: USB HID v1.10 Mouse [Generic USB Keyboard] on usb-70090000.xusb-2.1/input1
[    6.062474] usb 1-2.3: new low-speed USB device number 4 using tegra-xusb
[    6.091265] usb 1-2.3: New USB device found, idVendor=093a, idProduct=2510
[    6.098143] usb 1-2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    6.105448] usb 1-2.3: Product: USB Optical Mouse
[    6.110151] usb 1-2.3: Manufacturer: PixArt
[    6.117852] input: PixArt USB Optical Mouse as /devices/70090000.xusb/usb1/1-2/1-2.3/1-2.3:1.0/0003:093A:2510.0003/input/input4
[    6.129726] hid-generic 0003:093A:2510.0003: input,hidraw2: USB HID v1.11 Mouse [PixArt USB Optical Mouse] on usb-70090000.xusb-2.3/input0
[    8.687040] tegra-xusb 70090000.xusb: Upgrade port 0 to USB3.0
[    8.692867] tegra-xusb 70090000.xusb: Upgrade port 1 to USB3.0
[    9.015479] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb
[    9.054984] usb 2-1: New USB device found, idVendor=0bda, idProduct=0411
[    9.061688] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    9.068819] usb 2-1: Product: 4-Port USB 3.1 Hub
[    9.073434] usb 2-1: Manufacturer: Generic
[    9.083016] hub 2-1:1.0: USB hub found
[    9.088241] hub 2-1:1.0: 4 ports detected
[    9.250526] usb 2-1: usb_suspend_both: status 0
[    9.255166] usb usb2: usb_suspend_both: status 0
[   55.602520] random: crng init done
[  159.331020] EXT4-fs (mmcblk0p1): recovery complete
[  159.428003] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)
[  159.436898] Rootfs mounted over mmcblk0p1
[  209.767381] Switching from initrd to actual rootfs
...and this continues indefinelty