joepie91

Don't use VPN services.

No, seriously, don't. You're probably reading this because you've asked what VPN service to use, and this is the answer.

Note: The content in this post does not apply to using VPN for their intended purpose; that is, as a virtual private (internal) network. It only applies to using it as a glorified proxy, which is what every third-party "VPN provider" does.

• A Russian translation of this article can be found here, contributed by Timur Demin.
• A Turkish translation can be found here, contributed by agyild.
• There's also this article about VPN services, which is honestly better written (and has more cat pictures!) than my article.

ageis

security and hardening options for systemd service units

A common and reliable pattern in service unit files is thus:

NoNewPrivileges=yes
PrivateTmp=yes
PrivateDevices=yes
DevicePolicy=closed
ProtectSystem=strict

hubgit

Anonymising PDFs

PDF metadata

Metadata in PDF files can be stored in at least two places:

• the Info Dictionary, a limited set of key/value pairs
• XMP packets, which contain RDF statements expressed as XML

PDF files

rjhansen

SKS Keyserver Network Under Attack

This work is released under a Creative Commons Attribution-NoDerivatives 4.0 International License.

Terminological Note

"OpenPGP" refers to the OpenPGP protocol, in much the same way that HTML refers to the protocol that specifies how to write a web page. "GnuPG", "SequoiaPGP", "OpenPGP.js", and others are implementations of the OpenPGP protocol in the same way that Mozilla Firefox, Google Chromium, and Microsoft Edge refer to software packages that process HTML data.

Who am I?

kwk

.PHONY: using-gcc using-gcc-static using-clang

using-gcc:
	g++-4.8 -o main-gcc -lasan -O -g -fsanitize=address -fno-omit-frame-pointer main.cpp && \
	ASAN_OPTIONS=symbolize=1 ASAN_SYMBOLIZER_PATH=$(shell which llvm-symbolizer) ./main-gcc

using-gcc-static:
	g++-4.8 -o main-gcc-static -static-libstdc++ -static-libasan -O -g -fsanitize=address -fno-omit-frame-pointer main.cpp && \
	ASAN_OPTIONS=symbolize=1 ASAN_SYMBOLIZER_PATH=$(shell which llvm-symbolizer) ./main-gcc-static

larsch

Installing Arch Linux AArch64 on the NanoPi R2S

There is current no support for the NanoPi R2S in ArchLinuxArm, but it's possible to run it using the generic aarch64 installation.

Prepare sd-card/image

1. Copy bootloader and uBoot from an armbian image using for the NanoPi R2S using dd (sectors 32 to 32767) everything before the partition, except the partition table).
2. Create an ext4 partition on /dev/mmcblk0p1 at offset of 32768 sectors (16384 KiB):

Device         Boot Start      End  Sectors  Size Id Type

jult

#!/bin/sh

# This script runs every other night at 04:56 CET on a webserver I maintain
# Results are always at: https://jult.net/block.txt ( or https://jult.net/block.txt.gz )
# And much smaller, stripped of BS; https://jult.net/bloc.txt
# For use in Tixati IP filter: https://jult.net/bloc.txt.gz !!!
# And finally a txt file with just the bold IP-ranges: https://jult.net/bl.txt (or https://jult.net/bl.txt.gz )

# Download open block-lists, unpack, filter:
curl -s https://www.iblocklist.com/lists.php | grep -A 2 Bluetack | xargs wget -qO - --limit-rate=500k | gunzip -f | egrep -v '^#' > /tmp/xbp

dwisiswant0

#!/bin/bash

#####
#
# St8out - Extra one-liner for reconnaissance
#
# Usage: ./st8out.sh target.com
#
# Resources:
# - https://github.com/j3ssie/metabigor

ruario

The included script 'widevine-flash_armhf.sh' fetches a ChromeOS image for ARM and extracts the Widevine binary, saving it in a compressed archive. Since it downloads a fairly large file (2Gb+ on disk after download) it is recommended that you run the script on a machine that has plenty of disk space.

To install the resultant archive, issue the following on your ARM machine–after copying over the archive if needed:

sudo tar Cfx / widevine-flash-20200124_armhf.tgz

(Where 'widevine-flash-20200124_armhf.tgz' is updated to reflect the actual name of the created archive)

hasherezade

Windows Registry Editor Version 5.00

[HKEY_LOCAL_MACHINE\Software\Microsoft\Windows\CurrentVersion\Run]
@="Rundll32.exe SHELL32.DLL,ShellExec_RunDLL \"C:\\ProgramData\\test.exe\""