Klipper Ender 5 Plus stock printer config

printer.cfg

# This file contains pin mappings for the Creality Ender 5 Plus.
# Ender 5 Plus stock uses a Creality v2.2 board, similar to CR-20 Pro.
# To use this config, the firmware should be compiled for the AVR atmega2560.

# See the example.cfg file for a description of available parameters.

[stepper_x]
step_pin: PF0
dir_pin: PF1
enable_pin: !PD7
step_distance: .0125
endstop_pin: ^PE5
position_endstop: 350
position_max: 350
homing_speed: 100

[stepper_y]
step_pin: PF6
dir_pin: PF7
enable_pin: !PF2
step_distance: .0125
endstop_pin: ^PJ1
position_endstop: 350
position_max: 350
homing_speed: 100

[stepper_z]
step_pin: PL3
dir_pin: PL1
enable_pin: !PK0
step_distance: .001266
#step_distance: .0025
endstop_pin: probe:z_virtual_endstop
position_max: 400
position_min: -5 #set position_min to a negative value such as -5 when probing to set z offset, then revert to 0
homing_speed: 10.0

[extruder]
step_pin: PA4
dir_pin: PA6
enable_pin: !PA2
step_distance: .010526
nozzle_diameter: 0.400
filament_diameter: 1.750
#pressure_advance: 0.617 # high value for stock long bowden tube, uncomment to enable pressure advance
#pressure_advance_smooth_time: 0.010 # uncomment to enable pressure advance
heater_pin: PB4
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PK5
control: pid
pid_Kp: 22.2
pid_Ki: 1.08
pid_Kd: 114
min_temp: 0
max_temp: 260

[safe_z_home]
home_xy_position: 180, 180
speed: 100
z_hop: 10 # Move up 10mm, so the probe doesnt hit anything 
z_hop_speed: 5

[bltouch]
sensor_pin: ^PD3
control_pin: PB5
x_offset: -45
y_offset: 0
#z_offset: 0
speed: 3.0
samples: 1
pin_up_reports_not_triggered: True
pin_up_touch_mode_reports_triggered: False

[bed_mesh]
speed: 100
horizontal_move_z: 8
mesh_min: 50, 50
mesh_max: 300,300
probe_count: 3,3 # 3,3 or 5,5
  
[gcode_macro G29]
gcode: 
  G28
  BED_MESH_CALIBRATE
  BED_MESH_PROFILE SAVE=p1
  G1 X0 Y0 Z5 F4000
  
[heater_bed]
heater_pin: PH5
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PK6
control: pid
pid_Kp: 690.34
pid_Ki: 111.47
pid_Kd: 1068.83
min_temp: 0
max_temp: 130

[fan]
pin: PH6

[mcu]
serial: /dev/serial/by-id/usb-FTDI_FT232R_USB_UART_AK06VNAB-if00-port0

[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 2000 # 20x print speed recommended
max_z_velocity: 5
max_z_accel: 100

#[display]
# Not sure this is supported for E5+

@mnrivera210 I found the pin using my multimeter. First time I've used it for something like this :)

@Bob90
I've been using your config with great success! Only issue is after some time it appears to timeout and clear its position not allowing it to resume. Any idea how to keep it "Paused".

Also I've been trying to get the stock screen to work with no success so I tried to replace it with an lcd 12864, however I'm having a hard time getting the EXP1 & EXP2 pins to work. If you happen to know the pin out that would be great.

[display]
lcd_type: st7920
cs_pin: EXP1_4
sclk_pin: EXP1_5
sid_pin: EXP1_3
encoder_pins: ^EXP2_3, ^EXP2_5
click_pin: ^!EXP1_2
#kill_pin: ^!EXP2_8

[output_pin beeper]
pin: EXP1_1

Thank you again, you've really helped with getting the 5 Plus to be fully compatible with Klipper.

Hi, no idea on the LCD as I haven't tried yet.

There is an idle timeout setting that klipper has. Not sure on the default, but some suggested setting it yourself to a value of, say, 3000s (or 5 mins)

Hi, no idea on the LCD as I haven't tried yet.

There is an idle timeout setting that klipper has. Not sure on the default, but some suggested setting it yourself to a value of, say, 3000s (or 5 mins)

Does that mean after 5 mins it will timeout? Currently it takes about that time for it to timeout, is there a way to have indefinite?

I have mine set for 7200, but you should be able to set it higher. I haven't tested/checked this to see if Klipper has a limit that you need to override.

My Ender 5 Plus gives-me this error. I just installed and compiled Klipper.

Help appreciated...

Recv: // This type of error is frequently caused by running an older
Recv: // version of the firmware on the micro-controller (fix by
Recv: // recompiling and flashing the firmware).
Recv: // Once the underlying issue is corrected, use the "RESTART"
Recv: // command to reload the config and restart the host software.
Recv: // Protocol error connecting to printer
Recv: // Klipper state: Not ready

BTT TFT35.

[display]
lcd_type: emulated_st7920
spi_software_miso_pin: EXP2_1 #PB3
spi_software_mosi_pin: EXP1_3 #PH0
spi_software_sclk_pin: EXP1_5 #PA1
en_pin: EXP1_4 #PH1
encoder_pins: ^EXP2_5, ^EXP2_3 #PC4, PC6
click_pin: ^!EXP1_2 #PC2

[output_pin beeper]
pin: EXP1_1 #PG0

[board_pins]
aliases:
# EXP1 header
EXP1_1=PG0, EXP1_3=PH0, EXP1_5=PA1, EXP1_7=PA5, EXP1_9=,
EXP1_2=PC2, EXP1_4=PH1, EXP1_6=PA3, EXP1_8=PA7, EXP1_10=<5V>,
# EXP 2 header
EXP2_1=PB3, EXP2_3=PC6, EXP2_5=PC4, EXP2_7=PL0, EXP2_9=,
EXP2_2=PB1, EXP2_4=PB0, EXP2_6=PB2, EXP2_8=, EXP2_10=PG0

How did you find the pinout? I am trying to find the pin names for the Creality v2.1 board.

If you mean pinout for lcd, it should be same.

How did you find the pinout? I am trying to find the pin names for the Creality v2.1 board.

I think you asked on Reddit too?
I used a multimeter to read the resistance on the board pins and processor.

Other wat is to peak in marlin pin config files.
Pin/ramps.h

is anybody know the second heater pin no as heater pin 1 is PB4 ?

Got the stock filament sensor working. I used a multimeter to find the MCU pin name and played around with some macros from other Githhub users.

Hi Bob that was a genius solution. Just curious, how did you trigger the pins to probe them w meter? Because now I'm not even using the factory board lol. Thanks

Got the stock filament sensor working. I used a multimeter to find the MCU pin name and played around with some macros from other Githhub users.

Hi Bob that was a genius solution. Just curious, how did you trigger the pins to probe them w meter? Because now I'm not even using the factory board lol. Thanks

I just found ones when they were powered off. I didn't need to find them all. So just a continuity check with multimeter.

hi guys i am trying to add a second part cooling fan but for the life of me i can't find the correct pin out i guessed at the number and added this to my printer.cfg but it didn't work any help would be great thanks.

multi_pin my_fan]
pins: PH6, PH7

[fan]
pin = multi_pin:my_fan

hi guys i am trying to add a second part cooling fan but for the life of me i can't find the correct pin out i guessed at the number and added this to my printer.cfg but it didn't work any help would be great thanks.

multi_pin my_fan] pins: PH6, PH7

[fan] pin = multi_pin:my_fan

What mainboard do you have?

hi guys i am trying to add a second part cooling fan but for the life of me i can't find the correct pin out i guessed at the number and added this to my printer.cfg but it didn't work any help would be great thanks.
multi_pin my_fan] pins: PH6, PH7
[fan] pin = multi_pin:my_fan

What mainboard do you have?

It's a creality silent board version 2.2

Hello I am trying to get Klipper running on my Ender 5 Plus. I'm stuck at flashing the hex onto the mainboard. I have the Creality silent board v2.2
When I put the sd card with the compiled hex file nothing happens. I tried changing the hex to a bin file. I have heard rumors that i need to unplug the screen, and others that i need to use Cura to flash the firmware over, but no one that's actually done it, just people that say they heard.

any help at all is greatly appreciated

[Edit:] The screen prevents flashing on the Ender 5's. I used the RPi to flash the firmware over