Skip to content

Instantly share code, notes, and snippets.

@neuberfran
Created January 22, 2024 15:03
Show Gist options
  • Save neuberfran/d58ac784da21b208e4a2d36d99e1c026 to your computer and use it in GitHub Desktop.
Save neuberfran/d58ac784da21b208e4a2d36d99e1c026 to your computer and use it in GitHub Desktop.
U-Boot 2021.04-AUTOINC+gdb54757fd5 (Dec 09 2023 - 09:29:07 +0000)
CPU: i.MX7D rev1.2 1000 MHz (running at 792 MHz)
CPU: Commercial temperature grade (0C to 95C) at 43C
Reset cause: POR
Model: TechNexion PICO-IMX7D Board and PI baseboard
Board: i.MX7D PICOSOM
I2C: ready
DRAM: 1 GiB
PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11
MMC: FSL_SDHC: 2, FSL_SDHC: 1, FSL_SDHC: 0
Loading Environment from MMC... *** Warning - bad CRC, using default environment
[*]-Video Link 0 (800 x 480)
[0] lcdif@30730000, video
In: serial
Out: serial
Err: serial
flash target is MMC:0
Net: eth0: ethernet@30be0000
Fastboot: Normal
Normal Boot
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0(part 0) is current device
Failed to load Ret value 'fffffffes'
Failed to load Mudei 5 'uEnv.txt'
Failed to load Mudei 6 '80800000'
Failed to load Mudei 7 'bcd62184s'
Failed to load Mudei 2 'uEnv.txt'
Failed to load Mudei 3 '80800000'
Failed to load Mudei 4 'bcd62184s'
Failed to load Ret value 'fffffffes'
Failed to load Mudei 5 'boot.scr'
Failed to load Mudei 6 '80800000'
Failed to load Mudei 7 'bcd62184s'
Failed to load Mudei 2 'boot.scr'
Failed to load Mudei 3 '80800000'
Failed to load Mudei 4 'bcd62184s'
Failed to load Ret value 'fffffffes'
Failed to load Mudei 5 'tnrescue.itb'
Failed to load Mudei 6 '87880000'
Failed to load Mudei 7 'bcd62184s'
Failed to load Mudei 2 'tnrescue.itb'
Failed to load Mudei 3 '87880000'
Failed to load Mudei 4 'bcd62184s'
lmb_dump_all:
memory.cnt = 0x1
memory.size = 0x0
memory.reg[0x0].base = 0x80000000
.size = 0x40000000
reserved.cnt = 0x1
reserved.size = 0x0
reserved.reg[0x0].base = 0xbcd6199c
.size = 0x329e664
bd taltes = 0x80800000
Failed to load Ret value '0s'
Failed to load Mudei 5 'zImage'
Failed to load Mudei 6 '80800000'
Failed to load Mudei 7 'bcd62184s'
8664008 bytes read in 219 ms (37.7 MiB/s)
Booting from mmc ...
lmb_dump_all:
memory.cnt = 0x1
memory.size = 0x0
memory.reg[0x0].base = 0x80000000
.size = 0x40000000
reserved.cnt = 0x1
reserved.size = 0x0
reserved.reg[0x0].base = 0xbcd616f4
.size = 0x329e90c
Failed to load Ret value '0s'
Failed to load Mudei 5 'zephyr.bin'
Failed to load Mudei 6 '7f8000'
Failed to load Mudei 7 'bcd61edcs'
26420 bytes read in 25 ms (1 MiB/s)
## No elf image at address 0x007f8000
## Starting auxiliary core stack = 0x20002118, pc = 0x1FFF8E4D...
baseboard is pi
lmb_dump_all:
memory.cnt = 0x1
memory.size = 0x0
memory.reg[0x0].base = 0x80000000
.size = 0x40000000
reserved.cnt = 0x1
reserved.size = 0x0
reserved.reg[0x0].base = 0xbcd617c4
.size = 0x329e83c
bd taltes = 0x83000000
Failed to load Ret value '0s'
Failed to load Mudei 5 'imx7d-pico-pi-qca-m4.dtb'
Failed to load Mudei 6 '83000000'
Failed to load Mudei 7 'bcd61facs'
60378 bytes read in 28 ms (2.1 MiB/s)
## Flattened Device Tree blob at 83000000
Booting using the fdt blob at 0x83000000
Using Device Tree in place at 83000000, end 83011bd9
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.10.72-2.2.0-next+g000eb85263cb (oe-user@oe-host) (arm-poky-linux-gnueabi-gcc (GCC) 10.2.0, GNU ld (GNU Binutils) 2.36.1.20210209) #1 SMP PREEMPT Thu Jan 12 09:09:37 UTC 2023
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: TechNexion PICO-IMX7D with QCA WLAN module and PI baseboard
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] OF: reserved mem: failed to allocate memory for node 'linux,cma'
[ 0.000000] Reserved memory: created DMA memory pool at 0x007f8000, size 0 MiB
[ 0.000000] OF: reserved mem: initialized node cm4tcmcode@0x7f8000, compatible id shared-dma-pool
[ 0.000000] Reserved memory: created DMA memory pool at 0x00900000, size 0 MiB
[ 0.000000] OF: reserved mem: initialized node cm4sramcode@0x900000, compatible id shared-dma-pool
[ 0.000000] cma: Reserved 32 MiB at 0x9c000000
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000080000000-0x000000009fefffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080000000-0x000000008fefffff]
[ 0.000000] node 0: [mem 0x000000008ff00000-0x000000008fffffff]
[ 0.000000] node 0: [mem 0x0000000090000000-0x000000009fefffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fefffff]
[ 0.000000] percpu: Embedded 15 pages/cpu s32652 r8192 d20596 u61440
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129666
[ 0.000000] Kernel command line: console=ttymxc4,115200 root=/dev/mmcblk2p2 rootwait rw
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 464852K/523264K available (12288K kernel code, 1343K rwdata, 3144K rodata, 1024K init, 456K bss, 25644K reserved, 32768K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] Trampoline variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] random: get_random_bytes called from start_kernel+0x324/0x4e4 with crng_init=0
[ 0.000000] arch_timer: cp15 timer(s) running at 8.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 440795202120 ns
[ 0.000008] sched_clock: 56 bits at 8MHz, resolution 125ns, wraps every 2199023255500ns
[ 0.000022] Switching to timer-based delay loop, resolution 125ns
[ 0.000329] Ignoring duplicate/late registration of read_current_timer delay
[ 0.000361] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns
[ 0.001725] arch_timer: multiple nodes in dt, skipping
[ 0.002160] Console: colour dummy device 80x30
[ 0.002200] Calibrating delay loop (skipped), value calculated using timer frequency.. 16.00 BogoMIPS (lpj=80000)
[ 0.002223] pid_max: default: 32768 minimum: 301
[ 0.002393] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.002411] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.003286] CPU: Testing write buffer coherency: ok
[ 0.003593] CPU0: update cpu_capacity 1024
[ 0.003610] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.004271] Setting up static identity map for 0x80100000 - 0x80100060
[ 0.004394] rcu: Hierarchical SRCU implementation.
[ 0.004744] smp: Bringing up secondary CPUs ...
[ 0.005470] CPU1: update cpu_capacity 1024
[ 0.005478] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.005628] smp: Brought up 1 node, 2 CPUs
[ 0.005651] SMP: Total of 2 processors activated (32.00 BogoMIPS).
[ 0.005661] CPU: All CPU(s) started in SVC mode.
[ 0.006112] devtmpfs: initialized
[ 0.010758] Duplicate name in lcdif@30730000, renamed to "display#1"
[ 0.018895] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.019186] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.019214] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.020929] pinctrl core: initialized pinctrl subsystem
[ 0.022224] NET: Registered protocol family 16
[ 0.029531] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.031154] thermal_sys: Registered thermal governor 'step_wise'
[ 0.031430] cpuidle: using governor menu
[ 0.126443] vdd1p0d: supplied by regulator-dummy
[ 0.131547] vdd1p2: supplied by regulator-dummy
[ 0.207581] DDR type is DDR3!
[ 0.617758] No ATAGs?
[ 0.617890] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.617906] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.618945] imx7d-pinctrl 302c0000.iomuxc-lpsr: initialized IMX pinctrl driver
[ 0.619639] imx7d-pinctrl 30330000.pinctrl: initialized IMX pinctrl driver
[ 0.621238] imx mu driver is registered.
[ 0.626028] imx rpmsg driver is registered.
[ 0.627371] MU is ready for cross core communication!
[ 0.669194] vgaarb: loaded
[ 0.669952] SCSI subsystem initialized
[ 0.670542] usbcore: registered new interface driver usbfs
[ 0.670607] usbcore: registered new interface driver hub
[ 0.670662] usbcore: registered new device driver usb
[ 0.670831] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator
[ 0.671213] usb_phy_generic usbphynop3: supply vcc not found, using dummy regulator
[ 0.671656] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator
[ 0.673768] i2c i2c-0: IMX I2C adapter registered
[ 0.674688] i2c i2c-1: IMX I2C adapter registered
[ 0.676299] pca953x 3-0024: using no AI
[ 0.686078] pca953x 3-0024: failed writing register
[ 0.687132] i2c i2c-3: IMX I2C adapter registered
[ 0.688321] mc: Linux media interface: v0.10
[ 0.688377] videodev: Linux video capture interface: v2.00
[ 0.688478] pps_core: LinuxPPS API ver. 1 registered
[ 0.688490] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.688518] PTP clock support registered
[ 0.715965] virtio_rpmsg_bus virtio0: rpmsg host is online
[ 0.717266] MIPI CSI2 driver module loaded
[ 0.717331] Advanced Linux Sound Architecture Driver Initialized.
[ 0.718240] Bluetooth: Core ver 2.22
[ 0.718296] NET: Registered protocol family 31
[ 0.718307] Bluetooth: HCI device and connection manager initialized
[ 0.718325] Bluetooth: HCI socket layer initialized
[ 0.718339] Bluetooth: L2CAP socket layer initialized
[ 0.718367] Bluetooth: SCO socket layer initialized
[ 0.719030] clocksource: Switched to clocksource arch_sys_counter
[ 0.719255] VFS: Disk quotas dquot_6.6.0
[ 0.719340] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.728788] NET: Registered protocol family 2
[ 0.728958] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.729976] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.730018] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
[ 0.730078] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.730157] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.730262] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.730302] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.730521] NET: Registered protocol family 1
[ 0.731075] RPC: Registered named UNIX socket transport module.
[ 0.731093] RPC: Registered udp transport module.
[ 0.731102] RPC: Registered tcp transport module.
[ 0.731111] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.732127] PCI: CLS 0 bytes, default 64
[ 0.732808] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[ 0.734475] Bus freq driver module loaded
[ 0.735528] Initialise system trusted keyrings
[ 0.735774] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[ 0.742398] NFS: Registering the id_resolver key type
[ 0.742445] Key type id_resolver registered
[ 0.742457] Key type id_legacy registered
[ 0.742560] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.742574] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 0.861286] Key type asymmetric registered
[ 0.861307] Asymmetric key parser 'x509' registered
[ 0.861334] io scheduler mq-deadline registered
[ 0.861344] io scheduler kyber registered
[ 0.867622] pwm-backlight backlight: supply power not found, using dummy regulator
[ 0.873282] mxc_sdc_fb fb@0: NO mxc display driver found!
[ 0.874530] cma: cma_alloc: alloc failed, req-size: 8192 pages, ret: -12
[ 0.874550] mxsfb 30730000.lcdif: Unable to allocate framebuffer memory
[ 0.874562] mxsfb 30730000.lcdif: Failed to initialize fbinfo: -12
[ 0.874886] mxsfb: probe of 30730000.lcdif failed with error -12
[ 0.879761] imx-sdma 30bd0000.sdma: Direct firmware load for imx/sdma/sdma-imx7d.bin failed with error -2
[ 0.879782] imx-sdma 30bd0000.sdma: Falling back to sysfs fallback for: imx/sdma/sdma-imx7d.bin
[ 0.882085] mxs-dma 33000000.dma-apbh: initialized
[ 0.887742] pfuze100-regulator 3-0008: Full layer: 1, Metal layer: 1
[ 0.888457] pfuze100-regulator 3-0008: FAB: 0, FIN: 0
[ 0.888472] pfuze100-regulator 3-0008: pfuze3000 found.
[ 0.908162] 30a70000.serial: ttymxc4 at MMIO 0x30a70000 (irq = 70, base_baud = 1500000) is a IMX
[ 1.824013] printk: console [ttymxc4] enabled
[ 1.829650] 30a90000.serial: ttymxc6 at MMIO 0x30a90000 (irq = 71, base_baud = 5000000) is a IMX
[ 1.840427] imx sema4 driver is registered.
[ 1.860398] brd: module loaded
[ 1.872264] loop: module loaded
[ 1.876782] imx ahci driver is registered.
[ 1.887213] libphy: Fixed MDIO Bus: probed
[ 1.892366] tun: Universal TUN/TAP device driver, 1.6
[ 1.897640] CAN device driver interface
[ 1.906577] pps pps0: new PPS source ptp0
[ 1.913138] libphy: fec_enet_mii_bus: probed
[ 2.170147] fec 30be0000.ethernet eth0: registered PHC device 0
[ 2.176555] PPP generic driver version 2.4.2
[ 2.181259] PPP MPPE Compression module registered
[ 2.186233] usbcore: registered new interface driver r8152
[ 2.191819] usbcore: registered new interface driver lan78xx
[ 2.197536] usbcore: registered new interface driver asix
[ 2.203019] usbcore: registered new interface driver ax88179_178a
[ 2.209180] usbcore: registered new interface driver cdc_ether
[ 2.215082] usbcore: registered new interface driver smsc95xx
[ 2.220893] usbcore: registered new interface driver cdc_subset
[ 2.226861] usbcore: registered new interface driver zaurus
[ 2.232531] usbcore: registered new interface driver cdc_ncm
[ 2.238195] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.244745] ehci-pci: EHCI PCI platform driver
[ 2.249254] ehci-mxc: Freescale On-Chip EHCI Host driver
[ 2.255038] usbcore: registered new interface driver usb-storage
[ 2.261184] usbcore: registered new interface driver usbserial_generic
[ 2.267754] usbserial: USB Serial support registered for generic
[ 2.273826] usbcore: registered new interface driver ftdi_sio
[ 2.279621] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 2.286969] usbcore: registered new interface driver option
[ 2.292602] usbserial: USB Serial support registered for GSM modem (1-port)
[ 2.299686] usbcore: registered new interface driver pl2303
[ 2.305290] usbserial: USB Serial support registered for pl2303
[ 2.315167] edt_ft5x06 3-0038: supply vcc not found, using dummy regulator
[ 2.317570] snvs_rtc 30370000.snvs:snvs-rtc-lp: registered as rtc0
[ 2.328318] snvs_rtc 30370000.snvs:snvs-rtc-lp: setting system clock to 1970-01-01T00:00:00 UTC (0)
[ 2.337613] i2c /dev entries driver
[ 2.343002] pxp-v4l2 pxp_v4l2_out: initialized
[ 2.347638] usbcore: registered new interface driver uvcvideo
[ 2.353437] USB Video Class driver (1.1.1)
[ 2.360065] Bluetooth: HCI UART driver ver 2.3
[ 2.364522] Bluetooth: HCI UART protocol H4 registered
[ 2.369698] Bluetooth: HCI UART protocol BCSP registered
[ 2.375048] Bluetooth: HCI UART protocol LL registered
[ 2.380238] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 2.386536] Bluetooth: HCI UART protocol Marvell registered
[ 2.392191] usbcore: registered new interface driver btusb
[ 2.398718] sdhci: Secure Digital Host Controller Interface driver
[ 2.404934] sdhci: Copyright(c) Pierre Ossman
[ 2.409324] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.416807] sdhci-esdhc-imx 30b40000.mmc: voltage-ranges unspecified
[ 2.417292] sdhci-esdhc-imx 30b50000.mmc: voltage-ranges unspecified
[ 2.425643] caam 30900000.crypto: Entropy delay = 3200
[ 2.431202] sdhci-esdhc-imx 30b60000.mmc: voltage-ranges unspecified
[ 2.434839] sdhci-esdhc-imx 30b40000.mmc: Got CD GPIO
[ 2.458484] caam 30900000.crypto: Instantiated RNG4 SH0
[ 2.470687] caam 30900000.crypto: Instantiated RNG4 SH1
[ 2.475931] caam 30900000.crypto: device ID = 0x0a16030000000000 (Era 8)
[ 2.478275] mmc1: SDHCI controller on 30b50000.mmc [30b50000.mmc] using ADMA
[ 2.482735] caam 30900000.crypto: job rings = 3, qi = 0
[ 2.489774] mmc2: SDHCI controller on 30b60000.mmc [30b60000.mmc] using ADMA
[ 2.498325] mmc0: SDHCI controller on 30b40000.mmc [30b40000.mmc] using ADMA
[ 2.517772] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[ 2.525190] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 2.531035] caam algorithms registered in /proc/crypto
[ 2.532514] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 2.537808] caam 30900000.crypto: caam pkc algorithms registered in /proc/crypto
[ 2.544810] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[ 2.549187] caam 30900000.crypto: registering rng-caam
[ 2.558407] mmc1: queuing unknown CIS tuple 0x81 (9 bytes)
[ 2.566767] Device caam-keygen registered
[ 2.580439] caam-snvs 30370000.caam-snvs: violation handlers armed - non-secure state
[ 2.580964] mmc2: new DDR MMC card at address 0001
[ 2.588336] random: fast init done
[ 2.597258] mmcblk2: mmc2:0001 M62704 3.56 GiB
[ 2.598067] usbcore: registered new interface driver usbhid
[ 2.602442] mmcblk2boot0: mmc2:0001 M62704 partition 1 2.00 MiB
[ 2.607472] usbhid: USB HID core driver
[ 2.608716] debugfs: Directory '30390000.reset-controller-src' with parent 'regmap' already present!
[ 2.613908] mmcblk2boot1: mmc2:0001 M62704 partition 2 2.00 MiB
[ 2.617527] imx-rproc imx7d-cm4: mbox_request_channel_byname() could not locate channel named "txdb"
[ 2.632688] random: crng init done
[ 2.641635] imx-rproc imx7d-cm4: No txdb, ret -22
[ 2.645142] mmcblk2rpmb: mmc2:0001 M62704 partition 3 512 KiB, chardev (242:0)
[ 2.650185] remoteproc remoteproc0: imx-rproc is available
[ 2.657402] edt_ft5x06 3-0038: touchscreen probe failed
[ 2.662662] remoteproc remoteproc0: attaching to imx-rproc
[ 2.673486] remoteproc remoteproc0: remote processor imx-rproc is now attached
[ 2.679709] mmcblk2: p1 p2
[ 2.689583] sgtl5000 0-000a: sgtl5000 revision 0x11
[ 2.698556] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum
[ 2.739457] fsl-sai 308a0000.sai: failed to get mclk0 clock: -2
[ 2.742689] mmc1: new high speed SDIO card at address 0001
[ 2.751320] fsl-sai 308b0000.sai: failed to get mclk0 clock: -2
[ 2.784398] NET: Registered protocol family 26
[ 2.790095] NET: Registered protocol family 10
[ 2.795664] Segment Routing with IPv6
[ 2.799523] NET: Registered protocol family 17
[ 2.804044] Bridge firewalling registered
[ 2.808059] can: controller area network core
[ 2.812520] NET: Registered protocol family 29
[ 2.816968] can: raw protocol
[ 2.819992] can: broadcast manager protocol
[ 2.824192] can: netlink gateway - max_hops=1
[ 2.828811] Bluetooth: RFCOMM TTY layer initialized
[ 2.833748] Bluetooth: RFCOMM socket layer initialized
[ 2.838922] Bluetooth: RFCOMM ver 1.11
[ 2.842738] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 2.848055] Bluetooth: BNEP filters: protocol multicast
[ 2.853305] Bluetooth: BNEP socket layer initialized
[ 2.858275] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 2.864220] Bluetooth: HIDP socket layer initialized
[ 2.869252] lib80211: common routines for IEEE802.11 drivers
[ 2.875672] rfkill_gpio bt_rfkill: bt_rfkill device registered.
[ 2.882103] Key type dns_resolver registered
[ 2.893180] imx-cpufreq-dt imx-cpufreq-dt: cpu speed grade 2 mkt segment 0 supported-hw 0x4 0x1
[ 2.903260] Registering SWP/SWPB emulation handler
[ 2.908408] Loading compiled-in X.509 certificates
[ 2.952237] imx_usb 30b10000.usb: No over current polarity defined
[ 2.961908] usbmisc_imx 30b10200.usbmisc: vbus is error
[ 2.967147] usbmisc_imx 30b10200.usbmisc: Error occurs during detection: -22
[ 2.975841] imx_usb 30b20000.usb: No over current polarity defined
[ 2.985096] ci_hdrc ci_hdrc.1: EHCI Host Controller
[ 2.990037] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
[ 3.019169] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
[ 3.024925] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 3.033254] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.040520] usb usb1: Product: EHCI Host Controller
[ 3.045474] usb usb1: Manufacturer: Linux 5.10.72-2.2.0-next+g000eb85263cb ehci_hcd
[ 3.053166] usb usb1: SerialNumber: ci_hdrc.1
[ 3.058325] hub 1-0:1.0: USB hub found
[ 3.062301] hub 1-0:1.0: 1 port detected
[ 3.068062] imx_thermal 30360000.anatop:tempmon: Commercial CPU temperature grade - max:95C critical:90C passive:85C
[ 3.080276] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 3.090683] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 3.097331] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 3.106274] platform regulatory.0: Falling back to sysfs fallback for: regulatory.db
[ 3.129303] ALSA device list:
[ 3.132280] #0: audio-sgtl5000
[ 3.147444] EXT4-fs (mmcblk2p2): mounted filesystem with ordered data mode. Opts: (null)
[ 3.155821] VFS: Mounted root (ext4 filesystem) on device 179:2.
[ 3.163821] devtmpfs: mounted
[ 3.168184] Freeing unused kernel memory: 1024K
[ 3.189337] Run /sbin/init as init process
[ 3.207673] 8<--- cut here ---
[ 3.210749] Unhandled fault: imprecise external abort (0x1c06) at 0x76f008e0
[ 3.217806] pgd = 997a44be
[ 3.220517] [76f008e0] *pgd=84b58835, *pte=811d575f, *ppte=811d5c7f
[ 3.226995] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000007
[ 3.234671] CPU0: stopping
[ 3.237391] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.10.72-2.2.0-next+g000eb85263cb #1
[ 3.245571] Hardware name: Freescale i.MX7 Dual (Device Tree)
[ 3.251348] [<8010ec60>] (unwind_backtrace) from [<8010a0bc>] (show_stack+0x10/0x14)
[ 3.259105] [<8010a0bc>] (show_stack) from [<80c7981c>] (dump_stack+0x94/0xa8)
[ 3.266339] [<80c7981c>] (dump_stack) from [<8010ca8c>] (do_handle_IPI+0xf4/0x11c)
[ 3.273918] [<8010ca8c>] (do_handle_IPI) from [<8010cacc>] (ipi_handler+0x18/0x20)
[ 3.281501] [<8010cacc>] (ipi_handler) from [<8017a100>] (__handle_domain_irq+0x7c/0xd0)
[ 3.289606] [<8017a100>] (__handle_domain_irq) from [<804f7b9c>] (gic_handle_irq+0x80/0x94)
[ 3.297969] [<804f7b9c>] (gic_handle_irq) from [<80100b0c>] (__irq_svc+0x6c/0xa8)
[ 3.305455] Exception stack(0x81201ed8 to 0x81201f20)
[ 3.310511] 1ec0: 00000000 9fa33980
[ 3.318697] 1ee0: 00000001 81200000 00000001 c0773b0f 8120cdd8 9fa2f7b8 00000001 00000000
[ 3.326882] 1f00: 00000001 00000000 000087a9 81201f28 801a89e4 8088d500 20000013 ffffffff
[ 3.335073] [<80100b0c>] (__irq_svc) from [<8088d500>] (cpuidle_enter_state+0x170/0x358)
[ 3.343176] [<8088d500>] (cpuidle_enter_state) from [<8088d72c>] (cpuidle_enter+0x30/0x40)
[ 3.351453] [<8088d72c>] (cpuidle_enter) from [<80159ff8>] (do_idle+0x214/0x2ec)
[ 3.358862] [<80159ff8>] (do_idle) from [<8015a3d0>] (cpu_startup_entry+0x18/0x1c)
[ 3.366444] [<8015a3d0>] (cpu_startup_entry) from [<81100dfc>] (start_kernel+0x4b0/0x4e4)
[ 3.374636] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000007 ]---
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment