Credit to bones7456.
Change values in settings.py, place it in the same directory as fileserver.py then run python2 fileserver.py
otilrac
/ README.md
Created
December 7, 2020 19:39
— forked from bharadwaj-raju/README.md
simple python fileserver with authentication
otilrac
/ lighttpd.conf
Created
November 28, 2020 21:20
— forked from MinaMikhailcom/lighttpd.conf
Basic authentication configurations for Lighttpd under Ubuntu
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| apt install apache2-utils | |
| htpasswd -c /etc/lighttpd/.htpasswd <Username> #Replace <Username>, you will be prompted to enter the password. | |
| # Make sure that "mod_auth" is loaded in "server.modules". | |
| nano /etc/lighttpd/lighttpd.conf | |
| #Add the following to lighttpd.conf. | |
| auth.backend = "htpasswd" | |
| auth.backend.htpasswd.userfile= "/etc/lighttpd/.htpasswd" |
otilrac
/ servo_test.ino
Created
August 28, 2020 18:32
— forked from col/servo_test.ino
A simple Arduino sketch that allows you to control a brushless motor via an ESC (or any servo really) using inputs from the Arduino IDE serial monitor.
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| #include <Servo.h> | |
| Servo esc; | |
| int escPin = 9; | |
| int minPulseRate = 1000; | |
| int maxPulseRate = 2000; | |
| int throttleChangeDelay = 100; | |
| void setup() { |
otilrac
/ *nix_Genealogy.txt
Created
November 11, 2019 04:37
— forked from mutin-sa/*nix_Genealogy.txt
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| BSD | |
| FreeBSD | |
| pfSense | |
| OPNSense | |
| BSDRP | |
| Askozia | |
| FreeNAS | |
| NAS4Free | |
| OpenBSD | |
| securityrouter (commercial, https://securityrouter.org/) |
otilrac
/ Public_Time_Servers.md
Created
November 11, 2019 04:18
— forked from mutin-sa/Top_Public_Time_Servers.md
List of Top Public Time Servers
otilrac
/ pfSense as an OpenVPN client.md
Created
November 3, 2019 20:05
— forked from pae-id/pfSense as an OpenVPN client.md
pfSense as an OpenVPN client
#pfSense as an OpenVPN client for specific devices
##Introduction One of the most powerful features of pfSense is it’s ability to direct your data requests through different end-points using NAT rules. pfSense is amazing as an OpenVPN client because it can selectively route any device on the network through the VPN service (i.e., my tablets and TV go through US servers, while my smartphone, VoIP, computers go my local ISP).
This setup becomes extremely handy for use with applications which are not aware of OpenVPN protocol, eg. download managers, torrent clients, etc. Expecting privacy you should be positive that traffic won't go through your ISP's gateway in case of failure on side of VPN provider. And obviously OpenVPN client should automatically reconnect as soon as service goes live again.
Note: This How-To is meant for pfSense 2.1.x. For those using 2.2 Beta, there is a bug that prevents this from working. Read about here in the pfSense forum thread, “[cannot NAT trough OPT1 interface on multiw