Use this code to make your LD2410 sensor to work with ESP32 or ESP8266 board

ESPHome-YAML-ld2410-esp32.yaml

esphome:
  name: ld2410-esp32
  friendly_name: ld2410-esp32

esp32:
  board: esp32dev
  framework:
    type: arduino

# Enable logging
logger:

# Enable Home Assistant API
api:
  encryption:
    key: "IArm3ZGuqL1HLZXXbu4/L0ciw1TDSagu6THKP8LnFdo="

ota:
  password: "3373716c7967d461cf4bd0ce1ba42e9a"

wifi:
  ssid: !secret wifi_ssid
  password: !secret wifi_password

  # Enable fallback hotspot (captive portal) in case wifi connection fails
  ap:
    ssid: "Ld2410-Esp32 Fallback Hotspot"
    password: "AhxmD317i7r1"

captive_portal:
 
light:
  - platform: binary
    name: "Blue Status Light"
    output: light_output
    id: led_light
    restore_mode: ALWAYS_OFF
 
output:
  - platform: gpio
    pin: GPIO2
    id: light_output
 
i2c:
  sda: 21
  scl: 22
  scan: true
  id: bus_a
 
uart:
  id: ld2410_uart
  tx_pin: RX
  rx_pin: TX
  baud_rate: 256000
  parity: NONE
  stop_bits: 1
 
ld2410:
  uart_id: ld2410_uart
  throttle: 1500ms
  id: ld2410_comp
 
select:
  - platform: ld2410
    distance_resolution:
      name: distance resolution
    baud_rate:
      name: baud rate
    light_function:
      name: light function
    out_pin_level:
      name: out pin level
 
button:
  - platform: ld2410
    factory_reset:
      name: "factory reset"
    restart:
      name: "restart"
    query_params:
      name: query params
 
number:
  - platform: ld2410
    timeout:
      name: timeout
    max_move_distance_gate:
      name: max move distance gate
    max_still_distance_gate:
      name: max still distance gate
    g0:
      move_threshold:
        name: g0 move threshold
      still_threshold:
        name: g0 still threshold
    g1:
      move_threshold:
        name: g1 move threshold
      still_threshold:
        name: g1 still threshold
    g2:
      move_threshold:
        name: g2 move threshold
      still_threshold:
        name: g2 still threshold
    g3:
      move_threshold:
        name: g3 move threshold
      still_threshold:
        name: g3 still threshold
    g4:
      move_threshold:
        name: g4 move threshold
      still_threshold:
        name: g4 still threshold
    g5:
      move_threshold:
        name: g5 move threshold
      still_threshold:
        name: g5 still threshold
    g6:
      move_threshold:
        name: g6 move threshold
      still_threshold:
        name: g6 still threshold
    g7:
      move_threshold:
        name: g7 move threshold
      still_threshold:
        name: g7 still threshold
    g8:
      move_threshold:
        name: g8 move threshold
      still_threshold:
        name: g8 still threshold
    light_threshold:
      name: light threshold
 
text_sensor:
  - platform: ld2410
    version:
      name: "presenece sensor version"
    mac_address:
      name: "presenece sensor mac address"
 
switch:
  - platform: ld2410
    engineering_mode:
      name: "engineering mode"
    bluetooth:
      name: control Bluetooth
 
sensor:
  - platform: ld2410
    moving_distance:
      name: "Moving distance (cm)"
    still_distance:
      name: "Still Distance (cm)"
    moving_energy:
      name: "Move Energy (%)"
    still_energy:
      name: "Still Energy (%)"
    detection_distance:
      name: "Distance Detection (cm)"
    g0:
      move_energy:
        name: g0 move energy
      still_energy:
        name: g0 still energy
    g1:
      move_energy:
        name: g1 move energy
      still_energy:
        name: g1 still energy
    g2:
      move_energy:
        name: g2 move energy
      still_energy:
        name: g2 still energy
    g3:
      move_energy:
        name: g3 move energy
      still_energy:
        name: g3 still energy
    g4:
      move_energy:
        name: g4 move energy
      still_energy:
        name: g4 still energy
    g5:
      move_energy:
        name: g5 move energy
      still_energy:
        name: g5 still energy
    g6:
      move_energy:
        name: g6 move energy
      still_energy:
        name: g6 still energy
    g7:
      move_energy:
        name: g7 move energy
      still_energy:
        name: g7 still energy
    g8:
      move_energy:
        name: g8 move energy
      still_energy:
        name: g8 still energy
    light:
      name: light
 
  - platform: bh1750
    name: "Illuminance"
    address: 0x23
    update_interval: 30s
 
binary_sensor:
 
  - platform: ld2410
    has_target:
      name: Presence
    has_moving_target:
      name: Moving Target
    has_still_target:
      name: Still Target

Can I get zone options in this?

I still cannot be able to get my Esp Vroom32 to work, all configs came out Unknown for my sensor, anyone have the same issue :(? Nvm swapped out the TX and RX pins, it works now.

Swapped out in which way?

Hello. This Yaml code that you published is fine for D1 mini right?

I've try different Yaml files and still getting Unknown I'm using D1 mini and LD2410c , I have confirmed my wiring is correct but no go

any ideas

I get this message, I can count on help,
ERROR Running command failed: device reports readiness to read but returned no data (device disconnected or multiple access on port?)
ERROR Please try running esptool.py --before default_reset --after hard_reset --baud 460800 --port /dev/ttyUSB0 --chip esp32 write_flash -z --flash_size detect 0x10000 /data/build/ld2410-esp32/.pioenvs/ld2410-esp32/firmware.bin 0x1000 /data/build/ld2410-esp32/.pioenvs/ld2410-esp32/bootloader.bin 0x8000 /data/build/ld2410-esp32/.pioenvs/ld2410-esp32/partitions.bin 0xe000 /data/cache/platformio/packages/framework-arduinoespressif32/tools/partitions/boot_app0.bin locally.
INFO Upload with baud rate 460800 failed. Trying again with baud rate 115200.