Last active
March 5, 2017 20:02
-
-
Save symm/68aecad6e7a84806ce6ab6b192be0936 to your computer and use it in GitHub Desktop.
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
Anti Hijack Feature | |
1. Turn on ignition until the dash lights come on but don't start engine! | |
2. Lock the door using the lever on the door handle and then unlock 3 Times | |
3. Turn off ignition | |
4. Repeat 2 but with ignition OFF | |
5. Turn on ignition - should hear a beep | |
6. Lock door again as in 2 BUT ONLY ONCE - final beep should be heard | |
7. Done! | |
Doors should now lock at around 5mph. including reverse!!! | |
Self Diagnostics Mode | |
The Self Diagnostics Mode gives you in-depth information about your | |
engine and the actual numbers in digital. To use it, follow the steps: | |
* Insert Key but do not turn it on | |
* Press and hold the Trip Meter Reset Button | |
* While holding the reset button, Turn ignition until dash lights come on and | |
continue holding the button | |
* Within 10 seconds, the display should change to "test" in LCD font | |
and the needles will do a full sweeping. Release the Button | |
Pressing the button will now cycle through some 17 different modes | |
* 1. Shows a Gauge Sweep | |
* 2. Shows all 8's on the LCD (LCD TEST) | |
* 3. Illuminates all the bulbs on the dash | |
* 4. Displays hexadecimal value for ROM level | |
* 5. Displays the hexadecimal value for EE level | |
* 6. Shows DTC (Diagnostic Trouble Code) | |
* 7. Digital Speedometer - mph | |
* 8. Digital Speedometer - kph | |
* 9. N/A | |
* 10. Digital tachometer | |
* 11. Fuel volume | |
* 12. Engine coolant temperature | |
* 13. Battery voltage | |
* 14. ABS fail | |
* 15. Electronic brake distribution (EBD) failure | |
* 16. Illumination | |
* 17. Crank Sense | |
Global Opening | |
To reset the windows, follow these steps: | |
Hold the switch down until the window is all the way down | |
Release the switch then hold down again for 5 seconds | |
Press the switch so the window goes all the way up | |
Release the switch and press it up, again for 5 seconds | |
The window will now be set for one touch and global opening/closing. | |
Repeat this procedure for each individual window... | |
Turning Off Seatbelt Reminder | |
Before starting this procedure, make sure that... The handbrake's on It's in Park | |
or neutral.Ignition is off. All doors are closed (and you're in the car). All the | |
seatbelts are unbuckled. The headlamps are off. | |
Deactivating/Activating | |
Turn the ignition switch to position II. (Do not start the engine). | |
Wait until the safety belt warning indicator turns off. (Approximately one to two | |
minutes). | |
The next 3 steps must be completed within 60 seconds or the procedure must be | |
repeated. | |
Buckle then unbuckle the safety belt three times, ending with the safety belt | |
unbuckled. | |
Turn the headlamps ON then OFF. | |
Buckle then unbuckle the safety belt three times ending with the safety belt | |
unbuckled. | |
After this step the safety belt warning indicator will be illuminated for three | |
seconds. | |
Within seven seconds of the safety belt warning indicator turning off, buckle then | |
unbuckle | |
the safety belt. This will enable the belt minder if disabled or disable belt minder | |
if enabled. | |
The following sequence will confirm the belt minder is enabled: | |
The safety belt warning indicator flashes four times per second for three seconds. | |
Three seconds with the safety belt warning indicator off. The safety belt warning | |
indicator flashes four times per second for three seconds again. | |
The safety belt warning indicator flashing four times per second for three seconds | |
provides confirmation of belt minder disabled. | |
After confirmation,the deactivation/activation procedure is complete | |
1 If the vehicle doesn't have a seatbelt warning light, use the SRS (airbag) warning | |
indicator instead. | |
2 If the seatbelt light doesn't normally come on until you move, proceed as above, | |
without initially | |
waiting for the belt warning indicator to go off (in this case, after the second three | |
buckles, the | |
indicator will flash a couple of times, instead of being illuminated for 3 seconds) | |
Two Stage Unlocking | |
Press both Lock and Unlock buttons on you key at the same time, wait until the | |
indicator lights flash once. | |
When complete two stage unlocking will be activated / deactivated accordingly. | |
Remote Central Locking Programming Instructions: | |
Insert the ignition key and turn from position II (Ignition) to position 0 (off) | |
and back four times within three seconds. Remove the ignition key. | |
The locking control system is now in "learn mode" for the next 20 seconds the | |
red warning system LED stays on continuously to indicate this. | |
During the 20 seconds press one of the transmitter buttons. The remotes signal and | |
code number is learned by the locking module and is indicated by flashing the | |
warning system LED. | |
Wait until learn mode times out (20 seconds) or switch the ignition back to ON. | |
Program a new key (Note you require at least 2 keys to program another) | |
Insert the first programmed key into the ignition and turn to position II | |
Turn back to 0 and remove the key | |
Insert the second programmed key into the ignition and turn to position II | |
Turn back to 0 and remove the key | |
Key programming mode is now activated and you have ten seconds to: | |
Insert the unprogrammed new key into the ignition and turn to position II | |
Turn back to 0 and remove the key | |
Allow 10 seconds to pass for the system to exit programming | |
Guide ID: 10000000005697837Guide created: 17/02/08 (updated 04/06/09) |
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
Take your car remote and press the door unlock and lock buttons simultaneously for at least 4 seconds with the ignition off. | |
The direction indicators will flash twice to indicate that the unlocking function has been sucessfully re-programmed. | |
Pressing and holding both buttons simultaneously for at least four seconds again will change the function back. | |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment