Tasmota Script Ver. a for QS-WiFi-D01-TRIAC 150W 1CH-Dimmer

WiFi-Dimmer-Script.txt

>D
sw=0
tmp=0
cnt=0
tmr=0
hold=0
pwrt=0
slid=0
dim=""
doff="FF550005DC0A"
splo=2  ;short press lo limit
spup=10 ;short press up limit
ddir=0  ;dim dir 0/1
dmul=2.2 ;dim multipl 1..2.55
dstp=2 ;dim step/speed 1..5
dlo=15 ;dim lolimit min.0
dup=95 ;dim uplimit max.100
dval=50 ;start dim level 0..100

>B
print > Wifi-1CH-Dimmer-Script v2.0a <
print >>  QS-WiFi-D01 150W Dimmer   <<
;hide cnt webui
->WebSensor1 0
;reset cnt@teleperiod
->SetOption79 1
->Baudrate 9600
;boot sequ
=#snddim(dval)
delay(1000)
->SerialSend5 %doff%
=>Power1 0

>F
cnt=pc[1]
if chg[cnt]>0
;sw press
then sw=1
else sw=0
;sw not pressed
endif

; 100ms timer
tmr+=1
; short press
if sw==0
and tmr>splo
and tmr<spup
then
pwrt^=1
;change on/off
if pwrt>0
then
=#snddim(dval)
=>Power1 1
else
->SerialSend5 %doff%
=>Power1 0
endif
endif

; long press
if sw>0
then
if tmr>spup
then
hold=1
;off then on
if pwrt==0
then
pwrt=1
endif
;dim if on&hold
if pwrt>0
then
if ddir>0
then
;incr dimlevel
dval+=dstp
if dval>dup
then
;upper limit
dval=dup
endif
else
;decr dimlevel
dval-=dstp
if dval<dlo
then
;lower limit
dval=dlo
endif
endif
endif
endif
else
tmr=0
if hold>0
then
hold=0
;change dim dir
ddir^=1
endif
endif

if chg[dval]>0
then
=#snddim(dval)
=>Dimmer %dval%
endif

>E
; slider
slid=Dimmer
if chg[slid]>0
then
; dim per slider
if slid>0
then
dval=slid
else
pwrt=0
endif
endif

>P
; on/off webui
if pwr[1]>0
then
pwrt=1
dim="FF55"+hn(dval*dmul)+"05DC0A"
->SerialSend5 %dim%
else
pwrt=0
->SerialSend5 %doff%
endif

; subroutine
#snddim(tmp)
dim="FF55"+hn(tmp*dmul)+"05DC0A"
->SerialSend5 %dim%
#

Thanks for the reply!
any idea where I can download Tasmota 8.x with scripting enabled?
On the internet I can only find the latest version.

Hej,

if 7.1.1.1 ist as well ok for you there is an stripped down one incl. scripting, mqtt, hue and timer here:
https://github.com/sqw534/QS-Wifi-D01-Tasmota/blob/master/tasmota_7.1.1.1_scripter_mqtt_hue_timer.bin

Is running stable on all my devices since +1 year.
Otherwise you have to compile your own binary. Sources could be found here:
https://github.com/arendst/Tasmota/tree/pre-release-8.5.1
and an environment should be here: https://gitpod.io/#https://github.com/arendst/Tasmota/tree/pre-release-8.5.1

Might be that it doesn't work from scratch but could be a starting point.
A Howto is here: https://tasmota.github.io/docs/Gitpod/

Hope this helps. Enjoy

Hi,

Thank you so much!
For now I installed Tasmota 7.1.1.1 on the dimmer and works like a charm :-D

For info, I have been using 9.1.0 with the dimmer script fine
The latest, 9.3.1, seems to work - but as soon as the light is switched (which works) there is a watchdog restart

Upgrade to version 9.3.1. And I have watchdog restart too. :-(

in version 9.3.1 something a problem with SUBROUTINE calls.
I just remove #senddim(tmp)..
And replace all off CALLS:

#senddim(0)

to

=>SerialSend5 FF550005DC0A
=>Dimmer 0

and replace all on CALLS

=#senddim(dimval)

to

dim="FF55"+hn(dimval*dimmlp)+"05DC0A"
=>SerialSend5 %dim%
=>Dimmer %dimval%

It's a temporary variant, but now all works.

That didn't fix it for me - though luckily 9.1 works fine :-)
`>D
sw=0
tmp=0
cnt=0
tmr=0
hold=0
powert=0
slider=0
dim=""
shortprl=2 ;short press lo limit
shortpru=10;short press up limit
dimdir=0 ;dim direction 0/1
dimmlp=2.2 ;dim multiplier 1..2.55
dimstp=2 ;dim step/speed 1..5
dimll=15 ;dim lower limit min. 0
dimul=95 ;dim upper limit max. 100
dimval=70 ;start dim level 0..100

B
=>print > WiFi-Dimmer-Script-v1.0 <
=>Counter1 0
=>Baudrate 9600
; boot sequence
dim="FF55"+hn(dimval*dimmlp)+"05DC0A"
=>SerialSend5 %dim%
=>Dimmer %dimval%
delay(1000)
=>SerialSend5 FF550005DC0A
=>Dimmer 0

F
cnt=pc[1]
if chg[cnt]>0
; sw pressed
then sw=1
else sw=0
; sw not pressed
endif
; 100ms timer
tmr+=1
; short press
if sw==0
and tmr>shortprl
and tmr<shortpru
then
powert^=1
; change light on/off
if powert==1
then
dim="FF55"+hn(dimval*dimmlp)+"05DC0A"
=>SerialSend5 %dim%
=>Dimmer %dimval%
else
=>SerialSend5 FF550005DC0A
=>Dimmer 0
endif
endif

; long press
if sw>0
then
if hold==0
then
; change dim direction
dimdir^=1
endif
if tmr>shortpru
then
hold=1
if powert>0
; dim when on & hold
then
if dimdir>0
then
; increase dim level
dimval+=dimstp
if dimval>dimul
then
; upper limit
dimval=dimul
endif
dim="FF55"+hn(dimvaldimmlp)+"05DC0A"
=>SerialSend5 %dim%
=>Dimmer %dimval%
else
; decrease dim level
dimval-=dimstp
if dimval<dimll
then
; lower limit
dimval=dimll
endif
dim="FF55"+hn(dimvaldimmlp)+"05DC0A"
=>SerialSend5 %dim%
=>Dimmer %dimval%
endif
endif
endif
else
tmr=0
hold=0
endif

E
slider=Dimmer
; slider change
if chg[slider]>0
then
; dim according slider
if slider>0
then
dimval=slider
else
powert=0
endif
endif
if pwr[1]==1
; on/off webui
then
powert=1
dim="FF55"+hn(dimval*dimmlp)+"05DC0A"
=>SerialSend5 %dim%
=>Dimmer %dimval%
else
powert=0
=>SerialSend5 FF550005DC0A
=>Dimmer 0
endif
`

Somehow it worked on one of my dimmers but not the other one!
Same configuration, same everything!..

Hi, I have updated the Script to v2.0a with some changes and fixes to work with Tasmota v9.5.0 / 9.5.0.8 ...
(Ver.a: dimming stops when minimum or maximum brightness is reached)

and an alt. Script v2.0b
https://gist.github.com/thxthx0/12074f1f5249e14b2a0aada75f590c9b
(Ver.b: changes the dimming direction when min/max brightness is reached and doesn't stop dimming)

also working with the precompiled tasmota-scripting.bin / tasmota-scripting.bin.gz files:
https://github.com/tasmota/install/tree/main/firmware/unofficial

Template:
{"NAME":"QS-WiFi-D01 150W Dimmer","GPIO":[0,3200,0,3232,0,0,0,0,0,352,416,0,0,1],"FLAG":0,"BASE":18}

THANKS 👍 @ askold2, sqw534, gadget78, strike56 ...

I found today that the scripting builds I was using did not support MQTT autodiscovery - so I rebuilt one on gitpod, and got discovery working again.

The dimming on this version works as expected using the scripts above, as does the discovery over MQTT - however power toggles no longer work at all.

On attempting a toggle I now get:

23:54:29.999 SRC: WebGui from 192.168.1.154
23:54:30.002 var not found: Dimmer
23:54:30.012 MQT: tele/bedroom_light/STATE = {"Time":"2021-11-28T23:54:30","Uptime":"0T00:01:49","UptimeSec":109,"Heap":22,"SleepMode":"Dynamic","Sleep":10,"LoadAvg":19,"MqttCount":1,"POWER":"ON","Dimmer":40,"Fade":"OFF","Speed":1,"LedTable":"ON","Wifi":{"AP":1,"SSId":"barkernet","BSSId":"78:65:59:7C:9E:47","Channel":6,"Mode":"11n","RSSI":98,"Signal":-51,"LinkCount":1,"Downtime":"0T00:00:03"}}
23:54:30.018 MQT: stat/bedroom_light/RESULT = {"POWER":"ON"}
23:54:30.021 MQT: stat/bedroom_light/POWER = ON
23:54:30.555 CFG: Saved to flash at FB, Count 1356, Bytes 4096
23:54:42.435 WIF: Sending Gratuitous ARP
23:54:44.759 WIF: Checking connection...

Any thoughts?

Any thoughts?

Hi,

this must be set in my_user_config.h / user_config_override.h:

#define USE_SCRIPT                               // Add support for script (+17k code)
  #define SCRIPT_POWER_SECTION                   // enable >P section (execute on power changes)

or you may use:
https://github.com/tasmota/install/blob/main/firmware/unofficial/tasmota-scripting.bin
or
https://github.com/tasmota/install/blob/main/firmware/unofficial/tasmota-scripting.bin.gz

Ah - thanks very much, I missed that line. I will try it this evening.
When I initially tried the unofficial build, the dimmer worked, but then MQTT autodiscovery did not - I think it may be left commented out in the automatic builds - but I'll take a look

Thanks for the help

Thanks - getting there!
The precompiled binaries functioned, but did not have auto discovery MQTT enabled
My own build, with your extra #define line, got the power on/off section working fine along with auto discovery

At this point, the dimming works, but toggles on/off do not. I suspect there are some status messages that are not being sent/received as expected.

I think that is because I had not set:

#define TELE_ON_POWER true

from its default of false. Doing this has partially resolved the issue - there is now a STATE message on every power ON, but not one on POWER OFF. Still looking into why!

Domoticz requires a STATE message

maybe autodiscovery plugin issue (?) and maybe SetOption59 on helps,

I also use the dimmer with Domoticz and it works without autodiscovery,
(added the dimmer manually to Domoticz and inserted the Idx in Tasmota).

Thanks Yes, I have been looking at setOption59 as an alternative to setting it in code. Interestingly, in response to a request from Domoticz to turn the device off, it does indeed turn off, and responds over MQTT as follows: 18:00:29.403 MQT: tele/frontroom_light/STATE = {"Time":"2021-11-29T18:00:29","Uptime":"0T00:21:54","UptimeSec":1314,"Heap":24,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":52,"MqttCount":1,"POWER":"OFF","Dimmer":52,"Fade":"OFF","Speed":1,"LedTable":"ON","Wifi":{"AP":1,"SSId":"barkernet","BSSId":"78:65:59:8D:C2:81","Channel":6,"Mode":"11n","RSSI":66,"Signal":-67,"LinkCount":1,"Downtime":"0T00:00:03"}} 18:00:29.408 MQT: stat/frontroom_light/RESULT = {"POWER":"OFF"} 18:00:29.412 MQT: stat/frontroom_light/POWER = OFF However, Domoticz continues to assume it is ON - which is frustrating. But not, I suspect, any problem of yours! Thanks either way....perhaps an issue with Domoticz

Hi there,

using QS-WiFi-D01-TRIAC since about 2 years with old tasmota an 0.3 script. Since about a year WebUI does reacts anymore, last week dimmer stops working completly (also LED goes defective). So i have reflashed tasmota to reanimate the dimmer, using the actual version. Usind the new v2.0a script, but the light changes with some delay on changes in the WebUI slider and when I dim below 9% the LED begans to flicker and the dimmer resets. So i set limit minimal dimming rangen by setting dlo to 10 and with it works well with the wall switch, but using the slider in the webUi dimvalues below 10 can still be set causing a reset of the dimmer.

So i have read the scripting manual und changed some parts in the script 2.0a:

Changed GPIO14 from pwr1 to relay1 (to get rid of the "old" slider)

replaced

'>E
; slider
;slid=Dimmer
;if chg[slid]>0
;then
; dim per slider
;if slid>0
;then
;dval=slid
;else
;pwrt=0
;endif
;endif

by

'>W
sl(%dlo% %dup% dval "%dlo%" "%dval%" "%dup%")

for new slider.

When Dimmer is off and a differend dval than before is choosen with the new slider, die dimmer goes directly on. To also get correct state of relay1 (must toogle to Power1 1) by adding the following to the script in ^F section in dval-if-loop:

if sw==0
then
=>Power1 1
endif

before:

if chg[dval]>0
then
=#snddim(dval)
=>Dimmer %dval%
endif

after change:

if chg[dval]>0
then
=#snddim(dval)
=>Dimmer %dval%
if sw==0
then
=>Power1 1
endif
endif

pros:

• The new slider now shows the minimum an maximum values and the actual dimvalue an the LED and reacts much faster in changes in WebUi and can only moved in the ranges set in >D section.

cons:

• none konwn yet

Best regards

@MFe-tasmota
Cool!

A possible downside is that by changing GPIO14 to Relay, the integration with Home assistant will not be automatic, as it will be considered as a simple switch, losing the dimmer functionality.