Created
June 14, 2016 07:21
-
-
Save yamori813/5256549f309dd8e89d70e26fe552e580 to your computer and use it in GitHub Desktop.
AR2315 + 88E6060
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
+Ethernet eth0: MAC address 00:18:84:a5:84:e8 | |
IP: 10.10.10.99/255.255.255.0, Gateway: 0.0.0.0 | |
Default server: 10.10.10.3 | |
RedBoot(tm) bootstrap and debug environment [ROMRAM] | |
OpenWrt certified release, version 1.1 - built 22:32:28, May 7 2007 | |
Copyright (C) 2000, 2001, 2002, 2003, 2004 Red Hat, Inc. | |
Board: FON 2201 | |
RAM: 0x80000000-0x81000000, [0x80040290-0x80fe1000] available | |
FLASH: 0xa8000000 - 0xa87f0000, 128 blocks of 0x00010000 bytes each. | |
== Executing boot script in 2.000 seconds - enter ^C to abort | |
RedBoot> fis load -d kernel | |
Image loaded from 0x80050000-0x804beb74 | |
RedBoot> exec | |
Now booting linux kernel: | |
Base address 0x80030000 Entry 0x80050100 | |
Cmdline : | |
CPU platform: Atheros AR2315 rev 0 | |
CPU Frequency=184 MHz | |
CPU DDR Frequency=0 MHz | |
CPU AHB Frequency=92 MHz | |
platform frequency: 184000000 | |
arguments: | |
a0 = 00000002 | |
a1 = 80030020 | |
a2 = 80030000 | |
a3 = 0000001b | |
Cmd line: | |
Environment: | |
envp skiped | |
Cache info: | |
picache_stride = 4096 | |
picache_loopcount = 4 | |
pdcache_stride = 4096 | |
pdcache_loopcount = 4 | |
cpu0: MIPS Technologies processor v100.144 | |
MMU: Standard TLB, 16 entries (4K 16K 64K 256K 1M 16M 64M 256M pg sizes) | |
L1 i-cache: 4 ways of 256 sets, 16 bytes per line | |
L1 d-cache: 4 ways of 256 sets, 16 bytes per line | |
L2 cache: disabled | |
Config1=0x9e9b4d82<EJTAG> | |
Config2=0x80000000 | |
Config3=0x20 | |
AHB Master Arbitration Control 00000021 | |
Byteswap Control 0000842e | |
KDB: debugger backends: ddb | |
KDB: current backend: ddb | |
Copyright (c) 1992-2016 The FreeBSD Project. | |
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 | |
The Regents of the University of California. All rights reserved. | |
FreeBSD is a registered trademark of The FreeBSD Foundation. | |
FreeBSD 11.0-ALPHA3 #37 30062c6(zrouter)-dirty: Tue Jun 14 15:55:59 JST 2016 | |
hiroki@microserver:/storage/home/hiroki/obj/storage/home/hiroki/zrouter/tmp/ | |
mips.mips/storage/home/hiroki/freebsd/sys/Fon_FON2201 mips | |
gcc version 4.2.1 20070831 patched [FreeBSD] | |
real memory = 16777216 (16384K bytes) | |
avail memory = 11186176 (10MB) | |
random: entropy device external interface | |
nexus0: <MIPS32 root nexus> | |
clock0: <Generic MIPS32 ticker> on nexus0 | |
Timecounter "MIPS32" frequency 92000000 Hz quality 800 | |
Event timer "MIPS32" frequency 92000000 Hz quality 800 | |
apb0 at irq 0 on nexus0 | |
uart0: <16550 or compatible> on apb0 | |
uart0: console (9600,n,8,1) | |
gpio0: <Atheros AR5315 GPIO driver> on apb0 | |
gpio0: [GIANT-LOCKED] | |
gpio0: gpio pinmask=0x7fffff | |
gpiobus0: <GPIO bus> on gpio0 | |
gpioled0: <GPIO led> at pin 1 on gpiobus0 | |
gpioled2: <GPIO led> at pin 2 on gpiobus0 | |
gpioled3: <GPIO led> at pin 3 on gpiobus0 | |
gpioled4: <GPIO led> at pin 4 on gpiobus0 | |
gpioled5: <GPIO led> at pin 7 on gpiobus0 | |
gpioc0: <GPIO controller> on gpio0 | |
ar5315_wdog0: <Atheros AR5315 watchdog timer> on apb0 | |
spi0: <AR5315 SPI> at mem 0x11300000-0x1130000b on nexus0 | |
spibus0: <spibus bus> on spi0 | |
mx25l0: <M25Pxx Flash Family> at cs 0 mode 0 on spibus0 | |
mx25l0: mx25ll64, sector 65536 bytes, 128 sectors | |
are0: <AR231x Ethernet interface> at mem 0x10500000-0x109fffff irq 2 on nexus0 | |
are0: Overriding MAC address from environment: '00:18:84:A5:84:E8' | |
miiproxy0: <MII/MDIO proxy, MII side> on are0 | |
are0: can't attach proxy | |
are0: Ethernet address: 00:18:84:a5:84:e8 | |
aremdio0: <Atheros AR231x built-in ethernet interface, MDIO controller> at mem 0 | |
x10500000-0x109fffff on nexus0 | |
mdio0: <MDIO> on aremdio0 | |
mdioproxy0: <MII/MDIO proxy, MDIO side> on mdio0 | |
e6060sw0: Switch Identifier Register 602 | |
e6060sw0: Switch Identifier Register 602 | |
e6060sw0: <Marvell 88E6060 MDIO switch driver> on mdio0 | |
miibus0: <MII bus> on e6060sw0 | |
ukphy0: <Generic IEEE 802.3u media interface> PHY 0 on miibus0 | |
ukphy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto | |
miibus1: <MII bus> on e6060sw0 | |
ukphy1: <Generic IEEE 802.3u media interface> PHY 1 on miibus1 | |
ukphy1: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto | |
miibus2: <MII bus> on e6060sw0 | |
ukphy2: <Generic IEEE 802.3u media interface> PHY 2 on miibus2 | |
ukphy2: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto | |
miibus3: <MII bus> on e6060sw0 | |
ukphy3: <Generic IEEE 802.3u media interface> PHY 3 on miibus3 | |
ukphy3: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto | |
miibus4: <MII bus> on e6060sw0 | |
ukphy4: <Generic IEEE 802.3u media interface> PHY 4 on miibus4 | |
ukphy4: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto | |
etherswitch0: <Switch controller> on e6060sw0 | |
mdio1: <MDIO> on e6060sw0 | |
mdioproxy1: <MII/MDIO proxy, MDIO side> on mdio1 | |
Timecounters tick every 1.000 msec | |
e6060sw0port0: link state changed to DOWN | |
e6060sw0port1: link state changed to DOWN | |
e6060sw0port2: link state changed to DOWN | |
e6060sw0port3: link state changed to DOWN | |
e6060sw0port4: link state changed to DOWN | |
Trying to mount root from cd9660:/dev/redboot/rootfs.uzip []... | |
g_dev_taste: make_dev_p() failed (gp->name=redboot/RedBoot config, error=22) | |
g_dev_taste: make_dev_p() failed (gp->name=redboot/FIS directory, error=22) | |
warning: no time-of-day clock registered, system time will not be set accurately | |
e6060sw0port3: link state changed to UP | |
kern.coredump: 1 -> 0 | |
net.inet.ip.forwarding: 0 -> 1 | |
memory disk size = 6m | |
random: unblocking device. | |
add net default: gateway 10.0.1.1 | |
Thu Jan 1 00:00:35 UTC 1970 | |
login: |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment