RT3050 FDT

gistfile1.txt

U-Boot 1.1.3 (Nov 29 2009 - 20:59:38)

Board: Fonera
DRAM:  32 MB
relocate_code Pointer at: 81fac000
spi_wait_nsec: 3e 
spi deice id: c2 20 17 c2 20 (2017c220)
find flash: mx25l6405d
raspi_read: from:41030000 len:1000 
Using default environment


 ##### The CPU freq = 320 MHZ #### 

SDRAM bus set to 16 bit 
 SDRAM size =32 Mbytes

Please choose the operation: 
   1: Boot system code via Flash (default).
   2: Load system code then write to Flash via TFTP. 
   3: Entr boot command line interface.

booting from flash
## Booting image at bf020000 ...
raspi_read: from:20000 len:40 
   Image Name:   FreeBSD Kernel Image
   Created:      2016-09-27   2:57:43 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1080579 Bytes =  1 MB
   Load Address: 80001100
   Entry Point:  80001100
raspi_read: from:20040 len:107d03 
   1Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80001100) ...
## Giving linux memsize in MB, 32

Starting kernel ...

FDT DTB  at: 0x803249d0
CPU   clock:  320MHz
Timer clock:  160MHz
UART  clock:  106MHz

U-Boot args (from 0 args):
        None
Environment:
entry: mips_init()
RAM size: 32MB (assumed)
Cache info:
  picache_stride    = 4096
  picache_loopcount = 8
  pdcache_stride    = 4096
  pdcache_loopcount = 4
cpu0: MIPS Technologies processor v76.150
  MMU: Standard TLB, 32 entries (4K 16K 64K 256K 1M 16M 64M 256M pg sizes)
  L1 i-cache: 4 ways of 256 sets, 32 bytes per line
  L1 d-cache: 4 ways of 128 sets, 32 bytes per line
  L2 cache: disabled
  Config1=0xbea3319e<PerfCount,WatchRegs,MIPS16,EJTAG>
  Config2=0x80000000
  Config3=0x420
Physical memory chunk(s):
0x390000 - 0x1ffffff, 29818880 bytes (7280 pages)
Maxmem is 0x2000000
Copyright (c) 1992-2016 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 12.0-CURRENT #0 b1249a2(zrouter)-dirty: Tue Sep 27 11:54:52 JST 2016
    hiroki@microserver:/storage/home/hiroki/obj/storage/home/hiroki/zrouter/tmp/
mips.mipsel/storage/home/hiroki/freebsd/sys/Fon_FON2305E_FDT mips
gcc version 4.2.1 20070831 patched [FreeBSD]
Preloaded elf kernel "kernel" at 0x80383410.
real memory  = 33554432 (32768K bytes)
Physical memory chunk(s):
0x0041c000 - 0x01f40fff, 28463104 bytes (6949 pages)
avail memory = 28028928 (26MB)
ULE: setup cpu 0
firmware: 'rt2661fw' version 0: 8192 bytes loaded at 0x8032cb90
random: entropy device external interface
firmware: 'rt2860fw' version 0: 8192 bytes loaded at 0x8032ec10
firmware: 'rt2561fw' version 0: 8192 bytes loaded at 0x80328a90
firmware: 'rt2561sfw' version 0: 8192 bytes loaded at 0x8032ab10
wlan: <802.11 Link Layer>
mem: <memory>
null: <full device, null device, zero device>
openfirm: <Open Firmware control device>
nexus0: <MIPS32 root nexus>
random: harvesting attach, 8 bytes (4 bits) from nexus0
ofwbus0: <Open Firmware Device Tree> on nexus0
palmbus0: <MTK Palmbus> mem 0x10000000-0x101fffff on ofwbus0
random: harvesting attach, 8 bytes (4 bits) from palmbus0
random: harvesting attach, 8 bytes (4 bits) from ofwbus0
cpupic0: <MIPS32 Interrupt Controller> on ofwbus0
random: harvesting attach, 8 bytes (4 bits) from cpupic0
sysc0: <MTK System Controller> mem 0-0xff on palmbus0
random: harvesting attach, 8 bytes (4 bits) from sysc0
pinctrl0: <MTK Pin Controller> on ofwbus0
pinctrl0: GPIO mode start: 0x0000029d
Processing 1 pin-config node(s) in pinctrl-0 for spi@b00
Processing 1 pin-config node(s) in pinctrl-0 for uartlite@c00
Processing 1 pin-config node(s) in pinctrl-0 for pinctrl
pinctrl0: GPIO mode end  : 0x0000005d
random: harvesting attach, 8 bytes (4 bits) from pinctrl0
rstctrl0: <MTK Reset Controller> on ofwbus0
random: harvesting attach, 8 bytes (4 bits) from rstctrl0
clkctrl0: <MTK Clock Controller> on ofwbus0
random: harvesting attach, 8 bytes (4 bits) from clkctrl0
intc0: <MTK Interrupt Controller (v2)> mem 0x200-0x2ff irq 6 on palmbus0
random: harvesting attach, 8 bytes (4 bits) from intc0
gpio0: <MTK GPIO Controller (v1)> mem 0x600-0x633 irq 9 on palmbus0
gpiobus0: <OFW GPIO bus> on gpio0
random: harvesting attach, 8 bytes (4 bits) from gpiobus0
random: harvesting attach, 8 bytes (4 bits) from gpio0
cpulist0: <Open Firmware CPU Group> on ofwbus0
random: harvesting attach, 8 bytes (4 bits) from cpulist0
palmbus0: <timer@100> mem 0x100-0x11f irq 4 compat ralink,rt3050-timer (no drive
r attached)
palmbus0: <watchdog@120> mem 0x120-0x12f irq 5 compat ralink,rt3050-wdt (no driv
er attached)
palmbus0: <memc@300> mem 0x300-0x3ff irq 7 compat ralink,rt3050-memc (no driver 
attached)
palmbus0: <uart@500> mem 0x500-0x5ff irq 8 disabled compat ralink,rt3050-uart (n
o driver attached)
gpioled0: <GPIO led> at pin 14 on gpiobus0
random: harvesting attach, 8 bytes (4 bits) from gpioled0
gpioled1: <GPIO led> at pin 11 on gpiobus0
random: harvesting attach, 8 bytes (4 bits) from gpioled1
gpioled2: <GPIO led> at pin 9 on gpiobus0
random: harvesting attach, 8 bytes (4 bits) from gpioled2
gpioled3: <GPIO led> at pin 12 on gpiobus0
random: harvesting attach, 8 bytes (4 bits) from gpioled3
gpioc0: <GPIO controller> on gpio0
random: harvesting attach, 8 bytes (4 bits) from gpioc0
palmbus0: <gpio@638> mem 0x638-0x65b disabled compat ralink,rt3050-gpio (no driv
er attached)
palmbus0: <gpio@660> mem 0x660-0x683 disabled compat ralink,rt3050-gpio (no driv
er attached)
spi0: <MTK SPI Controller (v1)> mem 0xb00-0xbff on palmbus0
spibus0: <OFW SPI bus> on spi0
mx25l0: <M25Pxx Flash Family> at cs 0 mode 0 on spibus0
mx25l0: mx25ll64, sector 65536 bytes, 128 sectors
random: harvesting attach, 8 bytes (4 bits) from mx25l0
random: harvesting attach, 8 bytes (4 bits) from spibus0
random: harvesting attach, 8 bytes (4 bits) from spi0
uart0: <MTK UART Controller> mem 0xc00-0xcff irq 10 on palmbus0
uart0: console (57971,n,8,1)
uart0: fast interrupt
uart0: PPS capture mode: DCD
random: harvesting attach, 8 bytes (4 bits) from uart0
usbphy0: <MTK USB PHY> on ofwbus0
random: harvesting attach, 8 bytes (4 bits) from usbphy0
rt0: <Ralink RT3050 onChip Ethernet driver> mem 0x10100000-0x1010ffff irq 0 on o
fwbus0
rt0: RT305XF Ethernet MAC (rev 0x00000000)
rt0: use hardcoded 00:18:e7:d5:83:90 macaddr
rt0: bpf attached
rt0: Ethernet address: 00:18:e7:d5:83:90
random: harvesting attach, 8 bytes (4 bits) from rt0
mtkswitch0: <MTK Switch Driver> mem 0x10110000-0x10117fff irq 1 on ofwbus0
miibus0: <MII bus> on mtkswitch0
ukphy0: <Generic IEEE 802.3u media interface> PHY 0 on miibus0
ukphy0: OUI 0x000c43, model 0x0001, rev. 7
ukphy0:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
random: harvesting attach, 8 bytes (4 bits) from ukphy0
random: harvesting attach, 8 bytes (4 bits) from miibus0
miibus1: <MII bus> on mtkswitch0
ukphy1: <Generic IEEE 802.3u media interface> PHY 1 on miibus1
ukphy1: OUI 0x000c43, model 0x0001, rev. 7
ukphy1:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
random: harvesting attach, 8 bytes (4 bits) from ukphy1
random: harvesting attach, 8 bytes (4 bits) from miibus1
miibus2: <MII bus> on mtkswitch0
ukphy2: <Generic IEEE 802.3u media interface> PHY 2 on miibus2
ukphy2: OUI 0x000c43, model 0x0001, rev. 7
ukphy2:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
random: harvesting attach, 8 bytes (4 bits) from ukphy2
random: harvesting attach, 8 bytes (4 bits) from miibus2
miibus3: <MII bus> on mtkswitch0
ukphy3: <Generic IEEE 802.3u media interface> PHY 3 on miibus3
ukphy3: OUI 0x000c43, model 0x0001, rev. 7
ukphy3:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
random: harvesting attach, 8 bytes (4 bits) from ukphy3
random: harvesting attach, 8 bytes (4 bits) from miibus3
miibus4: <MII bus> on mtkswitch0
ukphy4: <Generic IEEE 802.3u media interface> PHY 4 on miibus4
ukphy4: OUI 0x000c43, model 0x0001, rev. 7
ukphy4:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
random: harvesting attach, 8 bytes (4 bits) from ukphy4
random: harvesting attach, 8 bytes (4 bits) from miibus4
etherswitch0: <Switch controller> on mtkswitch0
random: harvesting attach, 8 bytes (4 bits) from etherswitch0
mdio0: <MDIO> on mtkswitch0
random: harvesting attach, 8 bytes (4 bits) from mdio0
random: harvesting attach, 8 bytes (4 bits) from mtkswitch0
ofwbus0: <wmac@10180000> mem 0x10180000-0x101bffff irq 2 compat ralink,rt3050-wm
ac (no driver attached)
dwcotg0: <MTK DWC-OTG USB Controller> mem 0x101c0000-0x101fffff irq 3 on ofwbus0
usbus0 on dwcotg0
dwcotg0: usbpf: Attached
random: harvesting attach, 8 bytes (4 bits) from usbus0
random: harvesting attach, 8 bytes (4 bits) from dwcotg0
ofwbus0: <gpio-leds> compat gpio-leds (no driver attached)
ofwbus0: <gpio-keys-polled> compat gpio-keys-polled (no driver attached)
gpiopps0: <GPIO PPS> on ofwbus0
gpiopps0: PPS input on gpio0 pin 10
gpiopps0: Pin cannot be configured for the requested signal edge
device_attach: gpiopps0 attach returned 45
clock0: <Generic MIPS32 ticker> on nexus0
Timecounter "MIPS32" frequency 160000000 Hz quality 800
Event timer "MIPS32" frequency 160000000 Hz quality 800
random: harvesting attach, 8 bytes (4 bits) from clock0
Device configuration finished.
Timecounters tick every 10.000 msec
vlan: imtkswitch0port0: link state changed to DOWN
mtkswitch0port1: link state changed to DOWN
mtkswitch0port2: link state changed to DOWN
mtkswitch0port3: link state changed to DOWN
mtkswitch0port4: link state changed to DOWN
GEOM: new disk flash/spi0
usbus0: 480Mbps High Speed USB v2.0
nitialized, using hash tables with chaining
lo0: bpf attached
tcp_init: net.inet.tcp.tcbhashsize auto tuned to 512
ugen0.1: <DWCOTG> at usbus0
uhub0: <DWCOTG OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
Trying to mount root from cd9660:/dev/flash/spi0s.rootfs.uzip []...
MAP: No valid partition found at flash/spi0
flash/spi0: slice 00000000-0000ffff: u-boot (63KB)
flash/spi0: slice 00010000-0001ffff: u-boot-env (63KB)
flash/spi0: slice 00020000-0012ffff: kernel (1087KB)
flash/spi0: slice 00130000-0081ffff: rootfs (7103KB)
flash/spi0: slice 00020000-007fffff: upgrade (8063KB)
MAP: No valid partition found at flash/spi0s.u-boot
MAP: No valid partition found at flash/spi0s.u-boot-env
MAP: No valid partition found at flash/spi0s.kernel
MAP: No valid partition found at flash/spi0s.rootfs
MAP: No valid partition found at flash/spi0s.upgrade
MAP: No valid partition found at flash/spi0s.rootfs.uzip
cd9660: RockRidge Extension
warning: no time-of-day clock registered, system time will not be set accurately
start_init: trying /sbin/init
uhub0: 1 port with 1 removable, self powered
random: harvesting attach, 8 bytes (4 bits) from uhub0
ugen0.2: <Bit Trade One LTD.> at usbus0
mtkswitch0port0: link state changed to UP
Invalid flag: INT
kenv: unable to get HostName

kern.coredump: 1 -> 0
net.inet.ip.forwarding: 0 -> 1
memory disk size = 10m
MAP: No valid partition found at md0
random: unblocking device.
MAP: No valid partition found at md0

Thu Jan  1 09:00:32 JST 1970
login: