MZK-W04G

ARMboot 1.1.0 (Sep 13 2007 - 14:41:53)

Star maintain version 0.15.100000000
ARMboot code: 00000000 -> 0001b684

STR9100 CPU Clock: 250 Mhz

1.8V Regulator Regulated vdd Output : b101

2.5V Regulator Regulated vdd Output : b100

DDR Bank #0: 00000000 64 MB
DDR Controller Data Bus Width: 32 bits
flash type: EON_EN29LV640HL

Flash Bank #1: 8 MB

*** Using my specific environment

Hit any key to stop autoboot:  0 
## Starting application at 0x10040000 ...
Uncompressing Linux.............................................................
..................................... done, booting the kernel.
Linux version 2.6.16-star (root@localhost.localdomain) (gcc version 3.4.6) #197 
Mon Aug 17 19:31:34 JST 2009
CPU: FA526id(wb) [66015261] revision 1 (ARMv4)
Machine: STAR STR9100
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 2, 16 byte lines, 512 sets
CPU0: D cache: 16384 bytes, associativity 2, 16 byte lines, 512 sets
CPU clock at 250MHz
AHB clock at 125MHz
APB clock at 62MHz
Enable I-ScratchPad Address Start : c0026000 
Built 1 zonelists
Kernel command line: root=/dev/ram0
PID hash table entries: 512 (order: 9, 8192 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 64MB = 64MB total
Memory: 55812KB available (2500K code, 588K data, 120K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 5787K
NET: Registered protocol family 16
PCI clock at 33M
PCI: bus0: Fast back to back transfers disabled
PCI Bridge found
PCI: enabling device 0000:00:00.0 (0140 -> 0142)
PCI map irq: 00:00.00 slot 0, pin 1, irq: 0
PCI map irq: 00:01.00 slot 1, pin 1, irq: 5
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
NTFS driver 2.1.26 [Flags: R/O].
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
io scheduler noop registered
io scheduler deadline registered (default)
GPIO interrupt handler install ok. 
STR9100 Real Time Clock Driver v2.0.0
Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x78000000 (irq = 10) is a 16550A
RAMDISK driver initialized: 4 RAM disks of 18432K size 1024 blocksize
Star GSW Driver(for Linux Kernel 2.6) - Star Semiconductor
mac addr: 00:90:cc:00:00:00
mac len: 17
flash mac : 0:90:cc:00:00:00
VLAN0_VLAN_TAG: 1

configure VSC7385
Check MAC/PHY 0 Link Status : DOWN!
INIT VSC8601
VSC8601: AN Completed.
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
STR9100 NOR Flash: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
STR9100 NOR Flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 3 MTD partitions on "STR9100 NOR Flash":
0x00000000-0x00040000 : "ARMBOOT"
0x00040000-0x007e0000 : "Linux Kernel"
0x007e0000-0x00800000 : "Config"
str9100-ehci str9100-ehci: str9100-ehci
str9100-ehci str9100-ehci: new USB bus registered, assigned bus number 1
str9100-ehci str9100-ehci: irq 24, io mem 0xcc000000
str9100-ehci str9100-ehci: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (STR9100)
str9100-ohci str9100-ohci: str9100-ohci
str9100-ohci str9100-ohci: new USB bus registered, assigned bus number 2
str9100-ohci str9100-ohci: irq 23, io mem 0xc4000000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Netfilter messages via NETLINK v0.30.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
ip_conntrack version 2.4 (512 buckets, 4096 max) - 240 bytes per conntrack
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
ieee80211: 802.11 data/management/control stack, git-1.1.7
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem) readonly.
Freeing init memory: 120K
Mounting root fs rw ...
open mac port 0
port 0 already open
Init router config ...
str9100_shnat: module license 'Proprietary' taints kernel.
[RLDBG] init_func_ptr: HOOK POINT INIT OK 
STAR9100 Software HNAT Driver Initialized
star_ioctl: Unsupport command
device eth0 entered promiscuous mode
star_ioctl: Unsupport command
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
PCI: enabling device 0000:00:01.0 (0140 -> 0142)


=== pAd = c50b1000, size = 499588 ===

<-- RTMPAllocAdapterBlock, Status=0
pAd->CSRBaseAddress =0xc50a0000, csr_addr=0xc50a0000!
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
# RX DESC ffc30000  size = 2048
<-- RTMPAllocTxRxRingMemory, Status=0
Key1Str is Invalid key length(0) or Type(0)
1. Phy Mode = 0
2. Phy Mode = 0
RTMPSetPhyMode: channel is out of range, use first channel=0 
3. Phy Mode = 0
RTMPSetPhyMode: channel is out of range, use first channel=0 
MCS Set = 00 00 00 00 00
SYNC - BBP R4 to 20MHz.l
Main bssid = 00:90:cc:00:00:00
<==== rt28xx_init, Status=0
0x1300 = 00064220
device ra0 entered promiscuous mode
br0: port 2(ra0) entering learning state
br0: topology change detected, propagating
br0: port 2(ra0) entering forwarding state