Skip to content

Instantly share code, notes, and snippets.

@wacko
Last active July 13, 2024 00:48
Show Gist options
  • Save wacko/5577187 to your computer and use it in GitHub Desktop.
Save wacko/5577187 to your computer and use it in GitHub Desktop.
SSH between Mac OS X host and Virtual Box guest

On Mac OS (host):

Shutdown your VM and do:

VirtualBox > Settings > Network > Add (you will get vboxnet0)

On a terminal ifconfig will show you new interface vboxnet0

VM's Settings > System > check "Enable I/O APIC." VM's Settings > Network > Adapter 2 > host-only vboxnet0

On Ubuntu (guest):

Install OpenSSH Server

Edit /etc/network/interfaces file to append the following lines:

auto eth1
iface eth1 inet static
address 192.168.56.10
netmask 255.255.255.0

Run sudo ifup eth1 from the Ubuntu command line. SSH server should be up and running. Switch to your host terminal and enter ssh 192.168.56.10

sources:

@cakesummer
Copy link

I would like to post some new procedure in the new version of VirtualBox(5.2.12 r122591 (Qt5.6.3)) as follows:
File > Host Network Manager > Create (you will get vboxnet0)
...The rest is the same as above

@genidma
Copy link

genidma commented Jun 21, 2018

Instructions shared by @AnalyzePlatypus work.

Copy link

ghost commented Nov 14, 2018

Hey i have SSH working from local host MAC to VB ubuntu VM. however from gues os ubuntu i don't have internet connectivity. what do i need to do? do i need to create 3rd adapter or can i use the same adapter for internet as well.?

@zevaverbach
Copy link

Resolved some difficulty with this by reading a comment on this thread: It was as simple as appending a 0 to the end of the inet value shown for eth1 after invoking ifconfig. Once I replaced 192.168.33.1 (ifconfig's inet output) with 192.168.33.10, I was able to connect.

@ranjkkum
Copy link

I had considerable difficulty setting up.

This is what worked for me:
I followed the gist with @chao1995's suggestions.

In the VM:

$ ifconfig
lo        Link encap:Local Loopback 
enp0s8    Link encap:Ethernet ...

My etc/network/interfaces looks like this:

$ sudo nano etc/network/interfaces
GNU nano 2.5.3 
# Added this:
# Local Interface (for SSH)
auto enp0s8
iface enp0s8 inet static
address 192.168.56.10
netmask 255.255.255.0

To bring up the service, I ran:

$ sudo ifup enp0s8

In my host terminal:

$ ssh <username>@192.168.56.10
Welcome to Ubuntu 16.04.2 LTS ...

Wahoo!

Troubleshooting Checklist

In VirtualBox Manager

  • Is Settings > Network > Adaptor 2 set to Host-Only Adaptor (vboxnet0)?
  • Is Settings > System > Enable I/O APIC checked?

In the VM

  • Is OpenSSH installed? ($ sudo apt-get install openssh-server )
  • Have you made the changes to /etc/network/interfaces, replacing eth1 with your interface name from ifconfig ?
  • Have you brought up the adaptor with $ sudo ifup <interface name>?

On your host

  • Have you determined the correct IP address to ssh into? (Runifconfig. Use the value of vboxnet0's inet field. If vboxnet0 is not available, review the section above In VirtualBox Manager)
  • Run ssh <username>@<ip address> and log in.

I hope that helps.
Good luck out there!

thanks for sharing this .. this actually summarizes the issues once can face while enabling it ..

@bigjoe2000
Copy link

bigjoe2000 commented Nov 9, 2019

I had some trouble with this on my Ubuntu 18.04, which uses netplan instead of /etc/network/interfaces

Instead, I modified /etc/netplan/50-cloud-init.yaml to the following (The 192.168.99.2 is the static IP address I chose.)

network:
    ethernets:
        enp0s3:
            dhcp4: true
        enp0s8:
            dhcp4: no
            addresses: [192.168.99.2/24]
    version: 2

After editing the file, run

sudo netplan try

That will allow you to verify it's working before changing the virtual machine's network settings.

@jhamukesh998
Copy link

@bigjoe2000 is correct. Just a add on to this: use tab in yaml file.

@thomyi
Copy link

thomyi commented Mar 3, 2020

Are you doing on the VM's Settings or the VirtualBox preference? When I do an "+" I'm only seeing a new NAT connection created. Thanks!

@letchke
Copy link

letchke commented May 25, 2020

When I'm trying to ssh in on my host, I'm asked for a password. Neither the host nor the guest pw will work, any idea?

@danielverissimo
Copy link

Nice

@shiouming
Copy link

shiouming commented Nov 3, 2020

VirtualBox UI had been redesigned, the UI for step #1 had been moved to File > Host Network Manager.

I'm not sure which version this change was introduced into, perhaps long time ago? I'm on v6.1.16 for MacOS.

@jmiremba
Copy link

End-to-end, enabling connection from MacOS to hosted RHEL8 in VirtualBox 6.1

In VirtualBox (6.1.x):
- File > Host Network Manager ...
- Create (vboxnet0)

For the particular instance of VM (powered off):
- Settings > Network > Adapter 2
- Enable Network Adapter (checked)
- Attached to: Host-only Adapter
- Name: vboxnet0

Start the VM and login as root:
# nmcli dev status
	// Will show that enp0s8 is down
# nmcli con up enp0s8
# nmcli dev set enp0s8 autoconnect yes managed no
# nmcli dev connect enp0s8
# nmcli dev status
	// Will show that enp0s8 is connected
# ifconfig
	// Shows an inet IP address (192.168.56.101)

From the host (Terminal on MacOS):
$ sudo vim /etc/hosts
		*****
		192.168.56.101  vbox.rhel8
		*****
	:wq
$ ping -c 3 vbox.rhel8
$ ssh-copy-id jubilee@vbox.rhel8
$ ssh jubilee@vbox.rhel8 (using SSH keys, passwordless)

@Denis-Alexeev
Copy link

When I'm trying to ssh in on my host, I'm asked for a password. Neither the host nor the guest pw will work, any idea?

I am getting permission denied when i try to log in. What password should i be trying? Thanks!

I had the same problem. The reason was: I used "root" user. So, I had added 2 lines into sshd_config (in VM):

PermitRootLogin yes
PasswordAuthentication yes

and then (in VM terminal)
systemctl restart sshd

Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment