Build your own Audacity for Windows with ASIO driver support
Due to licensing restrictions the Audacity team cannot provide a prebuilt version with Windows ASIO driver support. But with this guide and script you can easily build your own Audacity 3.3.2.
Drivers are the glue between an audio program like Audacity and external hardware like a mixer or sound interface. The drivers usually used on Windows have limitations which can be overcome if you have ASIO drivers for your hardware. Specifically, low latency (delay) and multi channel support are available with ASIO drivers.
The Audacity program is the "go to" solution for many audio recording and editing tasks. However, unlike many more advanced DAWs, it doesn't support Windows ASIO drivers "out of the box". Fortunately, Audiacity's standard MME support is fine for most uses. That said, common reasons for needing ASIO include using digital audio or music equipment that only comes with ASIO drivers, such as Behringer mixers (which actually use the less efficient ASIO4ALL ASIO <> WDM bridging driver). Another common reason is to take advantage of the low latency or multiple channels supported by ASIO. Note that Audacity really is not a good multichannel solution, so if that is required a DAW might be a better bet.
While it is possible to build your own Audacity with ASIO support by following the instructions this usually requires considerable technical skills.
But have no fear, the instructions and script provided here make it easy to build your own version of Audacity with ASIO support. You just need a suitable Windows PC. The script checks all required tools are installed and builds a 64 bit release version of Audacity for you using the official build instructions.
NB. If you do use this to build Audacity with ASIO support you must not redistribute it due to the ASIO SDK licensing terms - see below.
Here's a brief blog post explaining why I needed ASIO and it includes a screen shot. But note, since writing that, I discovered my McMillen K-Mix digital interface mixer facilities alow routing of inputs 3 & 4 to the main outputs on 1 and 2 so can use the default MME Audacity build after all. For playback from PC, I found the HiFi Driver and ASIO Bridge from VB Audio lets me re-route PC audio out to channels 3 & 4 on the K-Mix, Leaving Channels 1 & 2 free for instruments and Mics.
The reason for Audacity's lack of ASIO support is licensing, not technical. Steinberg do not alow the ASIO SDK to be redistributed (as required by open source projects). In addition, Audacity is GPL licensed and so is incompatible with the ASIO SDK licence redistribution rules.
If you'd rather not impact your PC by installing everything described here you can install VirtualBox and use a Microsoft supplied Virtual Machine image as explained here.
Note for developers: These instructions assume a clean PC with no dev tools. If you have existing tools you may hit errors due to differing versions. Perhaps use a VM (difficult with Windows licencing) or a Windows container.
This video by @Renamesk walks you through the process, but the tool installation method has changed.
- ensure you have a PC with modern Windows installed. 11 and 10 are known to work but 7 and 8 should too.
- install "Git For Windows" - click the "download" button.
- make a new folder
- click on the 'raw' button at the top of the script (below) in this Gist.
- use the browser Save As feature to save the script as
\projects\build-audacity.cmd(be careful there's no ".txt")
- open a new Windows cmd terminal (Windows + R keys and then type
cd \projectsand enter key
- install required tools by typing
build-audacity.cmd --installand enter.
- NB for Visual Studio, make sure you check the "desktop development with C++" workload
- if you have a non English Windows or Visual Studio then you must also install the VS English language pack.
- when the install completes open a new cmd terminal and start the build by typing
- come back later - it will take at least 10 minutes
- Audactiy will be launched to test it was built correctly
- to it run again see the program location printed out at the end of the build
- or copy the specified folder to where you want to run Audacity from, optionally renaming it
If you have any ASIO drivers installed for active connected hardware you should find ASIO is now available in the the Audacity driver selection combo box.
When things go wrong
As with any complex software build there are many moving parts (including Windows itself) and things can sometimes go wrong. Here are some tips if you hit build errors.
- make sure you have latest script
- run the script with
--cleanalland try again
- uninstall all the tools (Python, cmake, Visual Studio and its installer) and then reboot before trying again
- note having other versions of any of the tools installed may well cause problems - remove them
- read the error output - clues are often buried in reams of impenetrable text
- disable any Anti Virus - the built-in Microsoft one is usually not a problem
- @diogodh for finding and fixing the bug with conan installations
- The Audacity team for an fantastic audio tool.
Thanks @Giermann and +1
@mapper14 a build can in theory complete without errors but not be correct. It appears to me that VS only allows the libs etc to be in c:\Program Files... so if you edited the script to say they are in D:\ I'd say your build config is indeterminate.
Also ASIO4ALL is the "bodge" driver I had in mind in my previous comment. AfAIK it makes windows drivers look like ASIO but without any of the multichannel or speed advantages. I suggest if you see it being used you have a run time config issue which you can best take to the Audacity team for support Best of luck.