Skip to content

Instantly share code, notes, and snippets.

@darconeous
Last active September 8, 2024 20:26
Show Gist options
  • Save darconeous/8c7899c4d2f849b881d6c43be55066ee to your computer and use it in GitHub Desktop.
Save darconeous/8c7899c4d2f849b881d6c43be55066ee to your computer and use it in GitHub Desktop.
Hacking the Rectangular Starlink Dishy Cable
@WIMMPYIII
Copy link

WimpyIII, I have a McCown POE and hooked my power supply to it. But before plugging DIshy into the POE Side can you confirm the cable termination configs with the McCown jumpered like this. I set the pins as suggested (see pic) . From the explanation on this pin setup I think it means I can use a normal ethernet cable from the Data ONLY side to the router. Versus the Tycon required a swapped end from the POE to a T568B to the router. If I use the McCown POE with this pin setting, do I still need to terminate from the DISH a swapped end termination ? That swapped end would go into the POWER DATA side of the McCown. I believe you have a working setup with the McCown POE.

IMG-6217

No swap with the McCown. Use 568B. The only reason for this swapping with the tycon is because you cannot change the power layout on it.
And the picture you have is the correct power layout for the dishy with jumpers on all 4 corners. You should be good to go.

@torrmundi
Copy link

Yes, burnt by crossed wires, from a McCown with wrong jumpers.

@jbowler
Copy link

jbowler commented Feb 19, 2023

For those who want to get rid of the motors this may help:

https://star-mountsystems.com/products/low-profile-flat-mount-for-rectangle-starlink-dishy

Read the instructions for installing the mount they sell; the pictures reveal a lot about the internals of the ethernet/PoE connection. I would be surprised if the 10-pin ethernet connector on the MB isn't just one of the standard ones. Personally I wouldn't remove the ferrite, it's unclear to me why they do that. It seems a simple connection to a waterproof RJ45 modular jack would solve all the problems of the oxidized/corroded SPX connector.

@petersticks
Copy link

Quick question… what is the best and proper way to connect the AC adapter to the McCown board? Just cut the cable and connect it?
Uploading image.jpg…

@WIMMPYIII
Copy link

Yes, sorry your picture isnt showing. If you are using a power pack style AC-DC with a lead plug already on it easiest way is to cut it off and crimp directly to whatever wire you are running to the injector or directly to the injector if you dont have any distance. I usually crimp to cat6 orange and brown + and green and blue - but mine are almost always 100ft or more to the injector and another 100-200ft up a tree.

@petersticks
Copy link

petersticks commented Feb 21, 2023

Yes, sorry your picture isnt showing. If you are using a power pack style AC-DC with a lead plug already on it easiest way is to cut it off and crimp directly to whatever wire you are running to the injector or directly to the injector if you dont have any distance. I usually crimp to cat6 orange and brown + and green and blue - but mine are almost always 100ft or more to the injector and another 100-200ft up a tree.

Thank you! Do I need to cut the wire before (exclude) or after (include) the ferrite bead? I cut it after and there is a center wire (positive) and shielded wire (negative) around that center one. Thanks again.

@WIMMPYIII
Copy link

On the reolink 52v the center is the positive and the outer wire is the ground. The ferrite I have done with and without and have not noticed any differences.

@bghira
Copy link

bghira commented Feb 22, 2023

new router/cable showed up yesterday so i attempted to use the new router with the RJ45 splicing technique to reuse the existing cable end from the roof, it turns out, however, that the connector at the dishy end of the cable is just absolutely garbage. I don't understand, because I used dielectric grease when installing. It worked great for a while. Then suddenly stopped working.

Replacing the entire cable temporarily with the brand new one (proprietary, in-tact) it works properly.

this is a shame, but the next step for me is to just cut the proprietary connector out of the dishy and use RJ45 the whole way through.

@WIMMPYIII
Copy link

new router/cable showed up yesterday so i attempted to use the new router with the RJ45 splicing technique to reuse the existing cable end from the roof, it turns out, however, that the connector at the dishy end of the cable is just absolutely garbage. I don't understand, because I used dielectric grease when installing. It worked great for a while. Then suddenly stopped working.

Replacing the entire cable temporarily with the brand new one (proprietary, in-tact) it works properly.

this is a shame, but the next step for me is to just cut the proprietary connector out of the dishy and use RJ45 the whole way through.

That is what I would do.

@jbowler
Copy link

jbowler commented Feb 22, 2023

[T]he connector at the dishy end of the cable is just absolutely garbage.

Not just the plug, the jack/socket in the dish mast too. I couldn't work out what the problem was for several days until I eventually cut the dish-end plug off the cable and checked it carefully; the orange and orange/white conductors were both shorted to ground. I think I detailed the cleaning I did above (DeoxIt, WD40 contact cleaner, water hydrogen peroxide) and this was not sufficient to "unshort" the solid orange.

However the dish jack also shows extra resistance (about 2ohms) on the solid orange connector even after I cleaned it several times. My system is working with that. I cut the dish-end plug off a new cable and used Deoxit F5 on both the plug and the jack. Nevertheless I don't like having that extra 2 ohms. Sure it's only one conductor but it's a specific failure point and it should take 1/4 of the current, about 0.4A continuous as measured. It will take less because of the higher resistance, 6 ohms vs 4 ohms in the other conductors, but it's going to dissipate significant power at the oxidized contacts.

When it fails (I'm sure it will) I'll pry the jack out of the mast and do the same thing. The link I posted above shows how to pry the jack out of the end of the mast and it looks like there is going to be enough flex in the lead to cut the inline jack off and do a solder/heat shrink join on all eight conductors. Heat shrink tubing with glue is appropriate here because it will provide a waterproof connection. I'll probably use the heat shrink butt connectors with internal heat melt solder, they work pretty well, though I do twist the conductors together and put a drop of flux on them too.

@bghira
Copy link

bghira commented Feb 22, 2023

yeah i already use the star-mount systems flat kit. but it doesn't encourage you to replace the proprietary jack (yet).

i opened up the very first router, the one that stopped outputting voltage of any kind, and found that it burned two or more of its pads out. the connector was no longer actually connected to the board. the tiny pads and wires that they're mounted through look rather inadequate.

same thing with the Tycon that i have that doesn't work. it has some pads blown out. in both cases for the SL router and the Tycon, the pads are gone. not just detached.

i would just get ahead of the issue and replace the crappy connector before it does greater damage.

@jbowler
Copy link

jbowler commented Feb 24, 2023

yeah i already use the star-mount systems flat kit. but it doesn't encourage you to replace the proprietary jack (yet).

If you've gone that far you've had access to the motherboard to disconnect the motor connector. The ethernet connector is in there too, just a 10-pin standard (I'm pretty sure) connector. Most likely 8 ethernet conductors plus two shield but the pictures I have aren't clear enough to be sure. Crimping a new connector with the StarLink cable and a new ferrite should allow the perfect solution. The StarLink cable seems pretty good, I believe it's the SPX connectors that are the problem.

I want to maximize my chances of getting a replacement from the StarLink customer support, when he comes back from his vacation. At this point that means preserving the connector even though I know it's damaged. At some point I will have to decide whether to just try to pull out the connector and solder it out of the way or to dremel the whole back off the dish. My inclination is to do the latter - I can flat mount it on my roof which, by design, points north-south and has about the optimal angle. I'll pull the MB connector and use some of the ~140ft of StarLink cable I have to wire it back to the PoE.

[I]n both cases for the SL router and the Tycon, the pads are gone. not just detached.

I haven't dremeled my defective router open yet. Just want to make sure the StarLink mgmt doesn't want it back. Even so mine failed gradually; disconnects over a period of several hours then permanent death. The problem might be caused by a short in the rectangular bit; a failed SPX connector at the antenna can certainly cause a Tycon or a McCown to blow out in this way because they are passive. The StarLink router PoE should be able to manage better but maybe it doesn't.

the ****** connector

I agree 110%

@torrmundi
Copy link

Oleg Kutkov has modded the rectangular dishy with an outdoor ethernet connector
See [https://olegkutkov.me/2022/03/07/reverse-engineering-of-the-starlink-ethernet-adapter/]
image

If you've gone that far you've had access to the motherboard to disconnect the motor connector. The ethernet connector is in there too, just a 10-pin standard (I'm pretty sure) connector. Most likely 8 ethernet conductors plus two shield but the pictures I have aren't clear enough to be sure. Crimping a new connector with the StarLink cable and a new ferrite should allow the perfect solution. The StarLink cable seems pretty good, I believe it's the SPX connectors that are the problem.

I want to maximize my chances of getting a replacement from the StarLink customer support, when he comes back from his vacation. At this point that means preserving the connector even though I know it's damaged. At some point I will have to decide whether to just try to pull out the connector and solder it out of the way or to dremel the whole back off the dish. My inclination is to do the latter - I can flat mount it on my roof which, by design, points north-south and has about the optimal angle. I'll pull the MB connector and use some of the ~140ft of StarLink cable I have to wire it back to the PoE.

@jbowler
Copy link

jbowler commented Feb 24, 2023

Oleg Kutkov has modded the rectangular dishy with an outdoor ethernet connector

I've been working to a large extent off the analysis Oleg posted; the link you quoted. However it doesn't contain the picture you posted. I have weatherproof connectors of that form and they can be used pretty easily in this application yet it is still necessary to drill a hole in the dish reverse. That looks like the wrong place to me because there is a big compartment around the mast entry point containing the motors; it's not enough to get into that compartment, it's necessary to get into the main compartment with the MB to do what I said.

@bghira
Copy link

bghira commented Feb 25, 2023

If you've gone that far you've had access to the motherboard to disconnect the motor connector. The ethernet connector is in there too, just a 10-pin standard (I'm pretty sure) connector. Most likely 8 ethernet conductors plus two shield but the pictures I have aren't clear enough to be sure. Crimping a new connector with the StarLink cable and a new ferrite should allow the perfect solution. The StarLink cable seems pretty good, I believe it's the SPX connectors that are the problem.

yeah i mentioned that already.

also, the shielding isn't really needed. neither is the ferrite core. the ferrite might cause bigger issues tbh.

@torrmundi
Copy link

torrmundi commented Feb 25, 2023 via email

@dreadlordchase
Copy link

dreadlordchase commented Feb 27, 2023

I'm looking to ditch the Starlink (rectangular dish) router all together and go with PoE injection. I'm going to use a DishyPowa so I'll just need a power supply. I've seen some linked but haven't been able to get any of them. I did find this one here that will take in 110/120vac and output 48vdc up to 3.13a. Seems like it should work well, but was hoping someone with a little more knowledge could tell me.

@WIMMPYIII
Copy link

Reolink 52v 150w used to be on Amazon for $35 but they are out of stock now. Here is one but you will have to get a us plug adapter.
https://www.aliexpress.com/item/1005004574962720.html

@jbowler
Copy link

jbowler commented Feb 27, 2023

I'm going to use a DishyPowa so I'll just need a power supply. I've seen some linked but haven't been able to get any of them.

The one I linked to is (still) available on Amazon:

https://www.amazon.com/gp/product/B08889XW1F

There's a 2A version on the same page which should be just fine. The Reolink is grounded; the ground (earth) pin of the mains supply is connected to the V- on the output. This varies with PSUs, I don't know about the one that I'm using (above) but I have a separate ground for the dish - I have a surge protector between the dish and the Tycon PoE I'm using.

@WIMMPYIII
Copy link

I'm going to use a DishyPowa so I'll just need a power supply. I've seen some linked but haven't been able to get any of them.

The one I linked to is (still) available on Amazon:

https://www.amazon.com/gp/product/B08889XW1F

There's a 2A version on the same page which should be just fine. The Reolink is grounded; the ground (earth) pin of the mains supply is connected to the V- on the output. This varies with PSUs, I don't know about the one that I'm using (above) but I have a separate ground for the dish - I have a surge protector between the dish and the Tycon PoE I'm using.

If you are going to go that route I would at least get the 3a.

@jbowler
Copy link

jbowler commented Feb 27, 2023

If you are going to go that route I would at least get the 3a.

What is your reasoning?

@WIMMPYIII
Copy link

WIMMPYIII commented Feb 27, 2023

These cheap supplies cant keep up nearly what they are rated for. Most people doing DC to DC conversations are actually picking 6-8 amp units because they can better handle the constant lower amp draw.

@crdiaz324
Copy link

Has anyone been able to figure out how to power the High-Performance dish off of DC power? I am thinking of getting one, but I don't want to have to go out and buy an inverter just to power it up.

@jbowler
Copy link

jbowler commented Mar 2, 2023

the High-Performance dish

Which one is that? This thread is about the rectangular dish (the V3, IRC); I don't think anyone has given any information about the newer StarLink offerings.

@WIMMPYIII
Copy link

the High-Performance dish

Which one is that? This thread is about the rectangular dish (the V3, IRC); I don't think anyone has given any information about the newer StarLink offerings.

He it talking about the $2500 HP. From what I have seen from it's performance it's not worth it. But there are some people on the Facebook SL hack group that have built DC conversations. I think they powered directly to the PCB pinouts inside the dish.

@torrmundi
Copy link

Remember I had the issue with Peplink BR1 Mini WAN port showing "No Cable Connected" when I used a POE and direct connection to Dishy (no SL router + Eth adapter)? Another telling symptom (thanks JBowler) is the exclusive reporting of ethSpeedMbps=100. I have now been able to connect Dishy <> PoE <> Peplink WAN and it works, as long as I set the WAN port speed below 1000Mbps. So 100Mbps half or full duplex and 10Mbps half or full duplex work fine. The setting is reached from dashboard, Wan Connection Status, Details, Physical Interface Settings, Port Speed. So I believe JBowler is correct in deducing that at least one of the four conductors in pair 3 and pair 4 paths has died within my Dishy. SpaceEx can see that there is a problem with ethernet connection speed and has sent me a new cable, new Eth adapter and (not yet received), a new router. None of which will solve this!

@WIMMPYIII
Copy link

@bghira
Copy link

bghira commented Mar 14, 2023

we're talking about hacking the wire and specs of the dishy on this gist. i know it's not my page, but can you not spam others with irrelevant youtube links? that just feels like advertising that service, which, honestly, who cares about it.

@WIMMPYIII
Copy link

we're talking about hacking the wire and specs of the dishy on this gist. i know it's not my page, but can you not spam others with irrelevant youtube links? that just feels like advertising that service, which, honestly, who cares about it.

Sorry to hurt your butt. I was just showing my application of the mod. Didn't realize it would be taken so offensively.

Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment